83.140.50 密封件 标准查询与下载

T/QGCML 642-2023 汽车玻璃用橡胶包边条

本标准规定了汽车玻璃用橡胶包边条的术语和定义、技术要求、检验方法、检验规则、标志、包装、运输和贮存。      本标准适用于汽车玻璃用橡胶包边条的生产及检验。

Rubber edging strip for automobile glass

KS M ISO 16010-2022 弹性密封件输送气体燃料和碳氢化合物流体的管道和配件中使用的密封件的材料要求

Elastomeric seals Material requirements for seals used in pipes and fittings carrying gaseous fuels and hydrocarbon fluids

T/TAOWBOL 0002-2022 酒用硅胶密封件

在白酒生产、运输、存储过程中，管道、酒罐、酒瓶等设备中的密封件均会与白酒长期接触，众所周知，白酒具有一定的酸性（酱香型白酒具有高酸、高酯的特点）且酒精是一种有机溶剂，这对长期接触甚至是浸泡在酒中的密封件的化学稳定性如浸出物、迁移量等指标提出了很高的要求，目前市场上无专门针对酒类行业设计生产的硅胶密封件，为促进酒用硅胶密封件技术进步，提高酒类设备密封质量，保障食品安全，泸州市耐尔密封件制造有限公司根据《泸州市酒类行业协会团体标准管理办法》章程及有关政策要求提出并制定本文件。

Silicone seals for wine

T/SHDSGY 091-2022 全氟醚橡胶密封件

本标准规定了全氟醚橡胶（FFKM）密封件的术语和定义、产品规格、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于全氟醚橡胶（FFKM）0型密封圈。

Perfluoroelastomer rubber seal

T/CFA 03035-2022 质量分级及“领跑者”评价要求 球墨铸铁管柔性接口用橡胶密封圈

本文件规定了球墨铸铁管柔性接口用橡胶密封圈质量及企业标准水平评价的术语和定义、评价指标体系和评价方法。

Assessment requirements for quality grading and forerunner-standards—Rubber sealing rings for ductile iron pipe flexible joint

HG/T 6049-2022 钻井泵用橡胶密封活塞

Rubber seal piston for drilling pump

HG/T 6048-2022 牙轮钻头用O形橡胶密封圈

O-ring rubber seal for roller cone drill bits

HG/T 6050-2022 管线阀门用抗气体快速减压橡胶密封圈

Anti-gas rapid decompression rubber seal for pipeline valves

HG/T 2701-2022 压缩式封隔器胶筒

Compression packer rubber barrel

T/CSTM 00540-2022 核电闸门用充气橡胶密封件

本文件规定了核电用充气橡胶密封件（以下简称“密封件”）的材料和结构、型别、要求、检验规则以及标志、包装、运输和贮存，界定了性能和试验涉及的术语和定义，描述了有关试验方法。 本文件适用于核岛内人员闸门和设备闸门上的充气橡胶密封件。

Inflatable rubber seals for nuclear power sluice gates

ASTM C1115-17(2022) 致密弹性硅橡胶垫圈和附件的标准规范

1.1 This specification describes products composed of dense elastomeric silicone rubber that are fabricated into gaskets and accessories (such as setting blocks, spacers, and shims) for use in sealing and glazing applications in building construction. These products are used to seal or serve as components of compression sealing systems between mechanically restrained surfaces in building construction and also as components in structural silicone sealant glazing systems. 1.2 The following precautionary statement pertains only to the test method portion, Section 10, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.3 Test Method C1166, as referenced in this specification, should be used to measure and describe the properties of materials, products, or assemblies in response to heat and flame under controlled laboratory conditions and should not be used to describe or appraise the fire hazard or fire risk of materials, products, or assemblies under actual fire conditions. However, results of this test may be used as elements of a fire risk assessment that takes into account all of the factors which are pertinent to an assessment of the fire hazard of a particular end use. 1.4 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.5 The committee with jurisdiction over this standard is not aware of any comparable standards published by other organizations. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Dense Elastomeric Silicone Rubber Gaskets and Accessories

ASTM D5898/D5898M-96(2021) 粘附防水板标准细节的标准指南

1.1 This guide covers details for typical conditions encountered in adhered sheet waterproofing on below-grade structures and plazas. 1.2 This guide does not cover liquid-applied waterproofing. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Standard Details for Adhered Sheet Waterproofing

ISO 3934:2021 建筑用预成型硫化热塑橡胶垫. 分类、规范和试验方法

This document specifies a system of classification of materials used in preformed gaskets for buildings. It applies to the following products: a) gaskets for use round the inside of door or window casings, i.e. weatherstripping (dynamic gaskets); b) gaskets for glazing (static gaskets); c) gaskets for use round infilling; d) gaskets for use between facade parts; e) gaskets for use between masonry walls. In addition to specifying the characteristics required for the constituent materials, some functional tests on the gaskets themselves are specified. The corresponding test procedures are given in Annexes A to E. This document applies to preformed gaskets made from vulcanized or thermoplastic rubber. It also applies to preformed gaskets made of cellular rubber designed for use at temperatures between −20 °C and +55 °C (thermal conditions category P1) and between −40 °C and +70 °C (thermal conditions category P3) (see Clause 4).

Rubber, vulcanized and thermoplastic - Preformed gaskets used in buildings - Classification, specifications and test methods

T/CEC 523-2021 六氟化硫高压电器设备用三元乙丙橡胶密封圈

本文件规定了六氟化硫高压电器设备用三元乙丙橡胶密封圈（以下简称“密封圈”）的技术要求，试验要求及试验方法，试验分类及项目，包装、标志、运输和储存方法。 本文件适用于采用六氟化硫气体作为绝缘介质的高压电器设备及其配套组件用三元乙丙橡胶密封圈，其他绝缘气体的设备或配套组件可参考使用。

EPDM sealing rings for sulfur hexafluoride high voltage electrical equipment

ASTM C1815-17(2021) 标准实践定期测量和监测压缩或张力一段时间后的密封胶尺寸稳定性

1.1 This practice covers a procedure for measuring and monitoring the physical dimensions of an elastomeric joint sealant in a test specimen configuration described in Test Method C719 following a period of compression or tension. These sealant materials are typically highly filled elastic materials. The dimensional change of these sealant materials is determined by measuring the dimensions at specific intervals over a period of time. 1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Periodically Measuring and Monitoring Sealant Dimensions to Stability Following a Period of Compression or Tension

HG/T 5839-2021 气弹簧用密封圈

Gas spring sealing ring

HG/T 5837-2021 发动机电子节温器用橡胶密封阀门

Rubber sealed valve for engine electronic thermostat

HG/T 5838-2021 金属骨架发泡橡胶复合密封板

Metal skeleton foam rubber composite sealing plate

T/ZJHJ 005-2020 机械膨胀式线缆管道封堵器

本文件规定了机械膨胀式线缆管道封堵器（以下简称为“封堵器”）的术语和定义、产品规格分类、标记和结构、技术要求、试验方法、检验规则、判定规则以及包装、标志、运输和贮存。 本文件适用于密封线缆管道的机械膨胀式线缆管道封堵器。

mechanical expansion type cable and pipe sealer

UNI ISO 3601-3:2020 流体动力系统“O 型圈”第3部分：质量验收标准

Fluid power systems — O-rings — Part 3: Quality acceptance criteria