87.060.30 溶剂 标准查询与下载

CNS 14691-2002 芳香烃溶剂

本标准适用于以芳香烃为主要成分之溶剂，供作油漆涂料、清漆之调制、杀虫剂、油墨、人造皮革、纺织品印染、防水剂、除草剂、木材防腐及人造树脂用之溶剂及稀释剂。

Aromatic solvent

CNS 14690-2002 脂肪烃溶剂

本标准适用于快干，挥发性强之脂肪烃，作为清除纺织油渍、清洗机件、皮革脱脂、油墨及油漆之溶剂、橡胶工业之溶剂、打火机之燃料等用途。

Aliphatic solvents

JIS K 5538:2002 清漆稀释料

この規格は，ニトロセルロースラッカーの希釈などに使用するラッカーシンナー及び塗装時の白化防止の目的でラッカーシンナーに混合して用いるリターダーについて規定する。

Lacquer thinner

ASTM D13-02 松脂油的标准规范

1.1 This specification covers the following kinds of spirits of turpentine as defined by the Code of Federal Regulations and Terminology D 804: gum spirits of turpentine, steam-distilled wood turpentine, sulfate wood turpentine, and destructively-distilled wood turpentine.1.2 The purchaser should specify the kind of spirits of turpentine desired.1.3 This specification is no longer widely used as it only specifies physical characteristics and not chemical composition. This specification was developed when the chief use for turpentine was as a solvent. Currently, especially in the United States, only a very limited quantity of turpentine is used as a solvent. Its main end use is as a raw material for the preparation of polyterpene type resins and synthetic organic chemicals. In spite of its limited application as a solvent, and hence the limited use of this specification, it is considered to be important to retain this specification. When information is required on chemical composition, gas chromatography is the recommended procedure (see Test Methods D 6387).

Standard Specification for Spirits of Turpentine

ASTM D2942-02(2008) 卤化有机溶剂的总酸容纳性的标准试验方法(非回流法)

p>Solvents that have been depleted in stabilizer content can become acidic. Acids can cause corrosion to process and storage equipment used for halogenated solvents. Halogenated organic solvents may contain amine type (alkaline, aqueous extractable) acid accepting additives, neutral type (typically epoxide) acid accepting additives or both. This test method can determine the combined acid acceptance from both types of stabilizers. In addition, if the amine acid acceptance is determined by a separate procedure (see Test Methods D 2106), the amount of neutral acid accepting stabilizers in a solvent can be calculated from the difference between combined and amine acid acceptance values. This test method may be used by producers and users to verify that a product is complying with acid acceptance product specifications or by users to monitor the acid accepting ability of a solvent in use.1.1 This test method covers the determination of the total acid acceptance including amine and neutral type (alpha epoxide) stabilizers in halogenated organic solvents. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 7.

Standard Test Method for Total Acid Acceptance of Halogenated Organic Solvents (Nonreflux Methods)

ASTM D801-02(2009) 双戊烯取样和测试的标准试验方法

The testing procedures described in these test methods have been in use for many years and emphasize the physical properties rather than the chemical composition of dipentene. These procedures were sufficient when dipentene was used primarily as a solvent. Currently, however, dipentene finds application as a chemical raw material and a knowledge of its chemical composition is therefore important. Test Methods D 6387 describe a capillary gas chromatography method which is suitable for determining both the major and minor components found in dipentene.1.1 These test methods cover procedures for sampling and testing dipentene and related terpene solvents, consisting chiefly of monocyclic terpene hydrocarbons distilling above the range for turpentine. 1.2 The procedures given in these test methods appear in the following order: Section Sampling 4 Detection and Removal of Separated Water 5 Appearance 6 Color 7 Odor 8 Specific Gravity 9 Refractive Index10 Composition11 Flash Point12 Moisture13 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Sampling and Testing Dipentene

ASTM D1296-01 挥发性溶剂和稀释剂气味的标准测试方法

1.1 This test method covers a comparative procedure for observing the characteristic and residual odors of volatile organic solvents and diluents to determine their odor acceptability in a solvent system. 1.2 It is not intended that this test method be employed to determine subtle odor differences between materials or to determine odor intensity. 1.3 It is recommended that this test method not be employed to determine the residual odor of a liquid if its time for evaporation to dryness at room temperature exceeds 30 min or as agreed upon. 1.4 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 4. 1.5 For specific hazard information, see the supplier's Material Safety Data Sheet (MSDS).

Standard Test Method for Odor of Volatile Solvents and Diluents

ASTM D365-84(1996)e1 可溶性硝化纤维素基溶液的标准试验方法

Standard Test Methods for Soluble Nitrocellulose Base Solutions

ASTM D3734-01 高闪光芳香石脑油标准规范

1.1 This specification covers two types of aromatic hydrocarbon solvents, normally petroleum distillates, having high flash points, moderately low volatility, and a distillation range of approximately 50oF (30oC). These solvents are used primarily by the coatings industry and are commonly referred to as high-flash aromatic naphthas. 1.2 For specific hazard information and guidance, see the supplier's Material Safety Data Sheet for materials listed in this specification.

Standard Specification for High-Flash Aromatic Naphthas

ASTM D2635-91(1996)e1 甲基异丁基甲醇的标准规格

Standard Specification for Methyl Isobutyl Carbinol

ASTM D365-01(2011) 可溶性硝酸纤维素基溶液的标准试验方法

Since the desired specifications and compositions of soluble nitrocellulose base solutions vary greatly, these methods are used to establish whether limits that shall be as agreed upon between the producer and the user have been met.1.1 This guide covers the testing of soluble nitrocellulose base solutions that are made by dispersing various kinds and concentrations of soluble nitrocellulose (cellulose nitrate) in various solvent mixtures. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements see Section 11.

Standard Guide for Soluble Nitrocellulose Base Solutions

DIN 55682:2000 色漆和清漆溶剂.在水里可以稀释的涂层材料中的溶剂测定.气相色谱法

The document described a method for the gas-chromatographic determination of the solvent content in water thinnable paints, varnishes, binder solutions, emulsions and dispersions.#,,#

Solvents for paints and varnishes - Determination of solvents in waterthinnable coating materials - Gas chromatographic method

JIS K 5421:2000 熟油及熟亚麻籽油

この規格は，ボイル油 及び煮あまに油の品質とその試験方法について規定する。

Boiled oil and boiled linseed oil

DIN 55997:2000 涂料和清漆用溶剂.去离子水.要求和试验方法

The document specifies requirements for deionized water used for electrodeposition paints, waterthinnable paints (industrial finishes), waterthinnable binders and emulsion paints and describes the corresponding test methods.

Solvents for paints and varnishes - Deionized water - Requirements and methods of test

CAN/CGSB-1.164-1999 乙烯基反应性底漆溶剂

1. OBJET 1.1 La présente norme s'applique au solvant à utiliser dans les peintures primaires réactives vinyliques conformes à CAN/CGSB-1.213. 1.2 Le solvant est destiné principalement au nettoyage de l'équipement ayant servi à l'application des peintures primaires réactives vinyliques. 1.3 La mise à l'essai et l'évaluation d'un produit en regard de la présente norme peuvent nécessiter l'emploi de matériaux ou d'équipement susceptibles d'être dangereux. Le présent document n'entend pas traiter de tous les aspects liés à la sécurité de son utilisation. Il appartient à l'usager de la norme de se renseigner auprès des autorités compétentes et d'adopter des pratiques d'hygiène et de sécurité conformes aux règlements en vigueur avant de l'utiliser.

Solvent for vinyl reactive primer paint

ASTM D6438-99 丙酮 乙酸甲酯和对氯三氟甲苯含量的固相微萃取 - 气相色谱法的标准测试方法

1.1 This test method is for the determination of acetone, methyl acetate, or parachlorobenzotrifluoride (PCBTF), or combination of any of the three, in paints and coatings, by solid phase microextraction (SPME) headspace sampling, and subsequent injection into a gas chromatograph. It has been evaluated for cellulose nitrate, acrylic, and urethane solvent-borne systems. The established working range of this test method is: acetone, 28 to 90%; methyl acetate, 12 to 22%; parachlorobenzotrifluoride, 10 to 17%. There is no reason to believe that it will not work ouside these ranges. A minor modification of this test method would make it suitable for the analysis of the same analytes in water-borne coatings (see Note 1). Note 1-Water-borne paints are internally standardized and diluted with water followed by addition of solid sodium chloride. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Acetone, Methyl Acetate, and Parachlorobenzotrifluoride Content of Paints, and Coatings by Solid Phase Microextraction-Gas Chromatography

CAN/CGSB-1.70-1999 高溶剂稀释剂

1. SCOPE 1.1 This standard applies to a high-solvency thinner for use with synthetic resin finishes. 1.2 The thinner is suitable for the general thinning of synthetic resin base finishes requiring a higher solvent power than provided by thinner conforming to CAN/CGSB-1.4, but not as high as thinner conforming to CAN/CGSB-1.94. 1.3 It is particularly suited for thinning materials by spray application because it evaporates faster than thinner conforming to CAN/CGSB-1.4 and the sprayed materials should show less tendency to sag. 1.4 The testing and evaluation of a product against this standard may require the use of materials and/or equipment that could be hazardous. This document does not purport to address all the safety aspects associated with its use. Anyone using this standard has the responsibility to consult the appropriate authorities and to establish appropriate health and safety practices in conjunction with any applicable regulatory requirements prior to its use.

High-Solvency Thinner

CAN/CGSB-1.124-1999 乙烯基树脂涂料稀释剂

1. OBJET 1.1 La présente norme s'applique à un mélange de liquides organiques destiné à être utilisé comme solvant ou diluant des revêtements à base de résines vinyliques. 1.2 Le diluant est destiné à être utilisé pour diluer la peinture anticorrosion pour couche primaire aux résines vinyliques et la peinture antisalissure aux résines vinyliques conformes à CAN/CGSB-1.122 et CAN/CGSB-1.123 respectivement. 1.3 La mise à l'essai et l'évaluation d'un produit en regard de la présente norme peuvent nécessiter l'emploi de matériaux ou d'équipement susceptibles d'être dangereux. Le présent document n'entend pas traiter de tous les aspects liés à la sécurité de son utilisation. Il appartient à l'usager de la norme de se renseigner auprès des autorités compétentes et d'adopter des pratiques d'hygiène et de sécurité conformes aux règlements en vigueur avant de l'utiliser.

Thinner for vinyl resin coatings

JIS K 5601-2-4:1999 涂料成份的试验方法.第2部分:溶剂溶解物质的成份分析.第4节:醇酸树脂

この規格は，塗料及びその類似品に使用されるアルキド樹脂の一般試験方法について規定する。また，塗料，ワニスのバインダー用の溶液及び同様な調製品にも適用可能である。 個々のアルキド樹脂に適用される試験方法は，関係者間の取決め事項による。

Testing methods for paint components -- Part 2: Component analysis in solvent soluble matter -- Section 4: Alkyd resin

JIS K 5601-2-1:1999 涂料成份的试验方法.第2部分:溶剂溶解物质的成份分析.第1节:酸值(滴定法)

この規格は，滴定法による塗料及びワニスの酸価測定方法を規定する。フェノール樹脂には適用できない。

Testing methods for paint components -- Part 2: Component analysis in solvent soluble matter -- Section 1: Acid value (titrimetric method)