91.100.50 粘合料、密封材料 标准查询与下载
共找到 1897 条与 粘合料、密封材料 相关的标准，共 127 页
Standard Specification for Coal Tar Primer Used in Roofing, Dampproofing, and Waterproofing
- ICS
- 91.100.50
- CCS
- 发布
- 2024-05-01
- 实施
Standard Specification for Coal Tar Roof Cement, Asbestos Free
- ICS
- 91.100.50
- CCS
- 发布
- 2024-05-01
- 实施
Standard Test Methods for Solvent Bearing Bituminous Compounds
- ICS
- 91.100.50
- CCS
- 发布
- 2024-05-01
- 实施
Standard Test Method for Estimating Degree of Particle Coating of Asphalt Mixtures
- ICS
- 91.100.50
- CCS
- 发布
- 2024-05-01
- 实施
.1 This guide describes the use of single and multicomponent, cold-applied joint sealants, or precured sealant systems for joint sealing applications, or both, in buildings using Exterior Insulation and Finish Systems (EIFS) on one or both sides of the joint. Refer to 10.1 for joint seal geometries. 1.2 The elastomeric sealants described by this guide meet the requirements of Specifications C834, C920, or C1311. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.5 There are no ISO standards similar or equivalent to this ASTM standard. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Guide for Use of Joint Sealants with Exterior Insulation and Finish Systems (EIFS)
- ICS
- 91.100.50
- CCS
- 发布
- 2024-04-25
- 实施
This document specifies a method for the determination of the change of mass and the change of volume of self-levelling and non-sagging sealants used in joints in building construction. NOTE This test procedure is not intended to determine the absolute maximum value of loss of mass and volume of a tested sealant, but it is an indicative measurement of the loss of mass and volume under specified parameters.
Building and civil engineering sealants — Determination of change in mass and volume
- ICS
- 91.100.50
- CCS
- 发布
- 2024-04-25
- 实施
1.总则；2.术语；3.建筑密封胶；4.接缝密封设计；5.接缝密封施工。
Technical specification for application of silicone and modified silicone building sealant
- ICS
- 91.100.50
- CCS
- E489
- 发布
- 2024-04-23
- 实施
- 2024-04-23
1.1 This test method pertains to the determination of the relative contents of ketone-ethylene-ester (KEE) and polyvinyl chloride (PVC) after their extraction from reinforced roofing membranes or fabrics. Based on proton nuclear magnetic resonance spectroscopy (1H-NMR), the method allows for the quantification of PVC with respect to an internal standard. The KEE content is then obtained by difference. The test method is not applicable to membranes or blends that contain high molecular weight polymers other than PVC and KEE. 1.2 Units— The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Test Methods for 1H-NMR Determination of Ketone-Ethylene-Ester and Polyvinyl Chloride Contents in KEE-PVC Roofing Fabrics
- ICS
- 91.100.50
- CCS
- 发布
- 2024-01-25
- 实施
1.1 This test method covers a laboratory procedure for determining the yield strength of preformed tape sealants. 1.2 The values stated in acceptable metric units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Note 1: There are no ISO standards similar or equivalent to this ASTM standard. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Test Method for Yield Strength of Preformed Tape Sealants
- ICS
- 91.100.50
- CCS
- 发布
- 2024-01-24
- 实施
1.1 This test method covers a laboratory procedure for determining the lap shear strength of sealants. It also provides information on the adhesive bond of the sealants to the tested substrates. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 The subcommittee with jurisdiction of this standard is not aware of any similar or equivalent ISO standard. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Test Method for Lap Shear Strength of Sealants
- ICS
- 91.100.50
- CCS
- 发布
- 2024-01-24
- 实施
1.1 This test method describes a laboratory procedure for determining the flow characteristics of preformed tape sealants after a specified time, temperature, and load. 1.2 The values stated in SI units are to be regarded as the standard. The inch-pound units given in parentheses are provided for information purposes only. 1.3 The committee with jurisdiction of this specification is not aware of any similar specification within ISO or any other organization. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Test Method for Flow Characteristics of Preformed Tape Sealants
- ICS
- 91.100.50
- CCS
- 发布
- 2024-01-24
- 实施
本文件规定了全钒液流电池电解液行业绿色工厂评价的评价原则、评价要求、评价方法和评价程序、评价报告。 本文件适用于全钒液流电池电解液行业绿色工厂的评价，可用于企业自我评价，第二方（相关方）或第三方组织评价。
Specification for green factory evaluation of adhesive manufacturing industry
- ICS
- 91.100.50
- CCS
- C313
- 发布
- 2024-01-19
- 实施
- 2024-01-19
本文件规定了胶粘剂行业绿色工厂评价的总则、评价要求、评价方法和评价程序、评价报告。 本文件适用于胶粘剂行业绿色工厂的评价，可用于企业自我评价，第二方（相关方）或第三方组织评价。
Specification for green factory evaluation of adhesive manufacturing industry
- ICS
- 91.100.50
- CCS
- C261
- 发布
- 2024-01-19
- 实施
- 2024-01-19
1. 粘结材料生产企业应按GB/T 33000要求建立安全生产制度。 2. 粘结材料生产企业应建立完整的原材料采购和使用台账，台账应包含原材料供应商名称、型号规格、购入数量、使用数量等内容。粘结材料生产企业不应使用国家和有关部门淘汰或禁止的技术、工艺及装备。 3. 粘结材料生产企业应依法依规排放污水。产生粉尘区域应安装除尘装置。空气中含有化学物质的区域应安装废气处置装置。 4. 粘结材料生产企业应建立危险废弃物处理台账。产生的危险废弃物的收集、贮存、处置应符合国家和地方相关法律法规的规定。 5. 粘结材料生产企业应建立一般固体废弃物处理台账。产生的一般固体废弃物的收集、贮存、处置应符合GB 18599的相关规定。 6. 粘结材料生产企业应采取措施减少产品生产过程中的碳排放，并应核算相应的碳足迹。
Technical requirements for green and low-carbon building materials Building bonding materials
- ICS
- 91.100.50
- CCS
- E501
- 发布
- 2024-01-01
- 实施
- 2024-01-08
Standard Guide for Use of Drainage System Media with Waterproofing Systems
- ICS
- 91.100.50
- CCS
- 发布
- 2024-01-01
- 实施
Standard Guide for Application of Heat Weldable Modified Bituminous Waterproofing Membranes Systems for New Concrete Decks
- ICS
- 91.100.50
- CCS
- 发布
- 2024-01-01
- 实施
Standard Test Method for Measurement of Asphalt Shingle Mechanical Uplift Resistance
- ICS
- 91.100.50
- CCS
- 发布
- 2024-01-01
- 实施
Standard Test Methods for Preformed Expansion Joint Fillers for Concrete Construction (Nonextruding and Resilient Types)
- ICS
- 91.100.50
- CCS
- 发布
- 2023-12-01
- 实施
Standard Practice for Sampling Asphalt Materials
- ICS
- 91.100.50
- CCS
- 发布
- 2023-12-01
- 实施
