91.100.50 粘合料、密封材料 标准查询与下载
共找到 1897 条与 粘合料、密封材料 相关的标准，共 127 页
Standard Test Methods for Preformed Expansion Joint Fillers for Concrete Construction (Nonextruding and Resilient Types)
- ICS
- 91.100.50
- CCS
- 发布
- 2023-12-01
- 实施
本文件规定了EPDM窗体密封件的术语和定义、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本文件适用于EPDM窗体密封件的生产及检验。
EPDM window seals
- ICS
- 91.100.50
- CCS
- C303
- 发布
- 2023-11-21
- 实施
- 2023-12-06
1适用范围的确定 传统型背网胶（又叫云石胶）现有的国家标准是JC/T 989—2006《非结构承载用石材胶粘剂》。石材用环保型背网胶与传统的云石胶、溶剂型背网胶相比，无论是化学组成、工作原理、性能指标、检测方法、施工方法、功能作用上都差异较大，无法套用现行的标准来评价产品的质量。因此，我们对本标准的使用范围进行了限制，仅适用于饰面石材与增强背网之间的环保型背网胶产品，溶剂型背网胶、云石胶等不适用于本标准。 2检测项目的确定 本标准参照了陶瓷粘胶剂、石材防护剂、防水背胶等产品标准的检测方法，又结合环保型石材背网胶的特点：是集增强、防护、防水等功能于一体的水性背网胶，于是在检验项目方面，我们选择了外观、拉伸粘结强度、浸水后的拉伸粘结强度、热老化后的拉伸粘结强度、冻融循环后的拉伸粘结强度、晾晒时间≥20min，拉伸胶粘强度、剪切粘结强度、抗渗性、水泥粘结强度下降率、挥发性有机化合物等具有代表性的几个项目，这些项目既能满足水性石材背网胶产品性能要求，又能促进水性石材背网胶由新兴产品向成熟产品过渡。
Environmentally friendly backing glue for natural stone
- ICS
- 91.100.50
- CCS
- E501
- 发布
- 2023-11-20
- 实施
- 2023-11-20
本文件规定了粘结材料的术语和定义、要求、检验规则、标志、运输和贮
bonding material
- ICS
- 91.100.50
- CCS
- E501
- 发布
- 2023-11-18
- 实施
- 2024-01-01
弹性恢复率（%）≥90； 拉伸模量（MPa）23℃≤0.4，-20℃≤0.6； 定伸粘结性无破坏；
Technical regulations for application of two-component modified silicone (MS) sealant
- ICS
- 91.100.50
- CCS
- E4710
- 发布
- 2023-11-06
- 实施
- 2023-11-08
Standard Test Method for Determining the Integrity of Nonreinforced Geomembrane Seams Produced Using Thermo-Fusion Methods
- ICS
- 91.100.50
- CCS
- 发布
- 2023-11-01
- 实施
Standard Test Method for Maximum Specific Gravity and Density of Asphalt Mixtures Using Automatic Vacuum Sealing Method
- ICS
- 91.100.50
- CCS
- 发布
- 2023-11-01
- 实施
Standard Practices for Electrical Methods for Mapping Leaks in Installed Geomembranes
- ICS
- 91.100.50
- CCS
- 发布
- 2023-11-01
- 实施
Standard Practice for Calculating Volume-Temperature Correction For Coal-Tar Pitches
- ICS
- 91.100.50
- CCS
- 发布
- 2023-10-01
- 实施
Standard Test Method for Microscopical Analysis by Reflected Light and Determination of Mesophase in a Pitch
- ICS
- 91.100.50
- CCS
- 发布
- 2023-10-01
- 实施
Standard Test Methods and Practices for Emulsified Asphalts
- ICS
- 91.100.50
- CCS
- 发布
- 2023-10-01
- 实施
Scope is not provided for this standard
Standard Test Method for Float Test for Bituminous Materials
- ICS
- 91.100.50
- CCS
- 发布
- 2023-09-10
- 实施
BS EN 1848-1. Flexible sheets for waterproofing. Determination of length, width and straightness - Part 1. Bitumen sheets for roof waterproofing
- ICS
- 91.100.50
- CCS
- 发布
- 2023-09-06
- 实施
- 2023-09-06
BS EN 12310-1. Flexible sheets for waterproofing - Part 1. Bitumen sheets for roof waterproofing. Determination of resistance to tearing (nail shank)
- ICS
- 91.100.50
- CCS
- 发布
- 2023-09-06
- 实施
- 2023-09-06
Standard Guide for Application of Aluminum-Pigmented Asphalt Roof Coatings
- ICS
- 91.100.50
- CCS
- 发布
- 2023-09-01
- 实施
Standard Test Method for Hydrostatic Pressure Resistance of a Liquid-Applied Waterproofing Membrane
- ICS
- 91.100.50
- CCS
- 发布
- 2023-09-01
- 实施
Standard Test Method for Crack Bridging Ability of Liquid-Applied Waterproofing Membrane
- ICS
- 91.100.50
- CCS
- 发布
- 2023-09-01
- 实施
Standard Practice for Sampling and Analysis of Existing Built-Up Roof Systems
- ICS
- 91.100.50
- CCS
- 发布
- 2023-09-01
- 实施
1.1 This guide covers the general effects of temperature from the aerosol foam sealant (either polyurethane or latex types) under the use temperatures. 1.2 The guide is intended to estimate the observed product dispensing characteristics and foam quality of aerosol foam dispensed or cured, or both, at specific temperatures and standard conditions. 1.3 Such foam sealants are primarily intended to reduce air movement in and out of building enclosures. 1.4 Currently two main foam sealant types are applicable to this standard: single component polyurethane and latex. 1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 There are no other known test methods specific for measuring the product temperature range for aerosol foam sealant. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Guide for Evaluating Temperature Effects to Aerosol Foam Sealant During and After Dispensing
- ICS
- 91.100.50
- CCS
- 发布
- 2023-08-02
- 实施
