91.100.50 粘合料、密封材料 标准查询与下载

T/YCST 005-2023 装配式建筑密封胶技术规程

本规程主要包括：1.总则；2.术语；3.材料；4.设计；5.施工；6.验收；7.检查与维修；附录A；附录B；附录C；附录D。

Technical specification for sealant of prefabricated building

T/CHBAS 31-2023 门、窗用包覆式PU发泡密封条

本文件规定了门、窗用包覆式PU发泡密封条（以下简称密封条）的分类、技术要求、试验方法、 检验规则、标志、包装、运输和贮存。 本文件适用于以PE材料包覆PU经发泡熟化后制成的一般门、窗用的密封条。

Covered PU foam sealing strips for doors and windows

ASTM D1669/D1669M-07(2023) 沥青涂层加速和户外风化试验板制备的标准实施规程

Standard Practice for Preparation of Test Panels for Accelerated and Outdoor Weathering of Bituminous Coatings

ASTM D1670/D1670M-11(2023) 沥青材料加速和室外风化失效终点的标准试验方法

Standard Test Method for Failure End Point in Accelerated and Outdoor Weathering of Bituminous Materials

T/SSM 12-2023 室内陶瓷砖美缝剂中壬基酚含量测定 气相色谱-质谱法

本文件建立一种美缝剂中壬基酚的快速、准确地测定方法，为本领域测试人员提供技术指导，为保护环境和人体健康提供技术支撑。规定了室内陶瓷砖美缝剂中壬基酚含量测定的原理、试剂和材料、仪器和设备、试样制备与保存、测定步骤、结果计算、精密度、其他和试验报告等要求。

Determination of nonylphenol content in indoor ceramic tile beautifying agent by gas chromatography-mass spectrometry

ASTM D8125-18(2023) 再精炼发动机油底部（REOB）/真空塔沥青增稠剂（VTAE）的标准规范

1.1 This specification covers re-refined engine oil bottoms, also known as vacuum tower asphalt extender, that may be used in formulating asphalt for pavement construction and roofing. This specification has been developed specifically for these two categories of product and is not intended for other uses. Table 1 is to be used for pavement construction and Table 2 for roofing. “Re-refined engine oil bottoms” (REOB) is the prevailing name used by many state highway agencies and FHWA, while “vacuum tower asphalt extender” (VTAE) is the preferred name used by the manufacturers of the product. Since each name provides an important descriptor of production elements (“re-refined” and “vacuum tower”) for the specific product this specification addresses, this specification uses the term “REOB/VTAE.” 1.2 Units—The values stated in either SI units or inchpound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Re-Refined Engine Oil Bottoms (REOB)/Vacuum Tower Asphalt Extender (VTAE)

ASTM C1401-23 结构密封胶玻璃的标准指南

1.1 Structural sealant glazing, hereinafter referred to as SSG, is an application where a sealant not only can function as a barrier against the passage of air and water through a building envelope, but also primarily provides structural support and attachment of glazing or other components to a window, curtain wall, or other framing system. 1.2 This guide provides information useful to design professionals, manufacturers, contractors, and others for the design and installation of a SSG system. This information is applicable only to this glazing method when used for a building wall that is not more than 15° from vertical; however, limited information is included concerning a sloped SSG application. 1.3 Only a silicone chemically curing sealant specifically formulated, tested, and marketed for structural sealant glazing is acceptable for a SSG system application. 1.4 The committee with jurisdiction for this standard is not aware of any comparable standard published by other organizations. 1.5 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. SI units in this guide are in conformance with IEEE/ASTM SI 10. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Structural Sealant Glazing

ASTM D3423/D3423M-15(2023) 乳化煤沥青（矿物胶体型）应用的标准实施规程

1.1 This practice covers the application of mineral-colloidstabilized, emulsified coal-tar pitch meeting the requirements of Specification D5727/D5727M, as a weather protection and aliphatic-solvent-resistant sealer for use on bituminous pavements of airports, parking lots, and driveways. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Application of Emulsified Coal-Tar Pitch (Mineral Colloid Type)

ASTM D8051/D8051M-16(2023) 屋面用蜡改性沥青标准规范

1.1 This specification covers wax-modified asphaltic products intended for use in built-up roof construction, construction of bituminous vapor retarder systems, adhering fleece-backed single-ply roof membranes, and adhering insulation boards used in various types of roof systems. The specification is intended for general classification purposes only, and does not imply restrictions on roofing system design, such as the slope at which this asphalt may be used. 1.2 These products have lower application temperatures compared to products specified by Specification D312/D312M. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Wax-Modified Asphalt Used in Roofing

ASTM D2202-00(2023) 密封剂坍落度的标准测试方法

Standard Test Method for Slump of Sealants

ASTM C1257-15(2023) 溶剂释放型密封剂加速老化的标准试验方法

Standard Test Method for Accelerated Weathering of Solvent-Release-Type Sealants

ISO 10563:2023 建筑和土木工程密封剂质量和体积变化的测定

Building and civil engineering sealants — Determination of change in mass and volume

ASTM D3462/D3462M-23 由玻璃毡制成并用矿物颗粒表面处理的沥青瓦的标准规范

1.1  This specification covers asphalt roofing in shingle form, composed of glass felt or felts impregnated and coated on both sides with asphalt, and surfaced on the weather side with mineral granules. This specification is designed for the evaluation of products as manufactured. The test methods, physical requirements, and minimum masses are to be measured immediately after packaging or at a reasonable time, as agreed upon between buyer and seller, after manufacture and before installation. Physical and performance requirements after application and during in-service use of the products described herein are beyond the scope of this material specification. 1.2  Shingles meeting this specification are intended to be applied with a headlap of not less than 51 mm [2 in.]. 1.3  The shingles shall be supplied with a factory-applied self-sealing adhesive or be designed to be locked together during installation of the shingles. 1.4  The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.5  The following safety hazards caveat pertains only to the test method described in this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Asphalt Shingles Made from Glass Felt and Surfaced with Mineral Granules

ASTM C1193-16(2023) 接缝密封剂使用标准指南

1.1  This guide describes the use of a cold liquid-applied sealant for joint sealing applications. Including joints on buildings and related adjacent areas, such as plazas, decks, and pavements for vehicular or pedestrian use, and types of construction other than highways and airfield pavements and bridges. Information in this guide is primarily applicable to a single and multi-component, cold liquid-applied joint sealant and secondarily to a precured sealant when used with a properly prepared joint opening and substrate surfaces. 1.2  An elastomeric or non-elastomeric sealant described by this guide should meet the requirements of Specification C834 , C920 , or C1311 . 1.3  This guide does not provide information or guidelines for the use of a sealant in a structural sealant glazing application. Guide C1401 should be consulted for this information. Additionally, it also does not provide information or guidelines for the use of a sealant in an insulating glass unit edge seal used in a structural sealant glazing application. Guide C1249 should be consulted for this information. 1.4  Practice C919 should be consulted for information and guidelines for the use of a sealant in an application where an acoustic joint seal is required. 1.5  This guide also does not provide information relative to the numerous types of sealant that are available nor specific generic sealant properties, such as hardness, tack-free time, or curing process, among others. 1.6  The values stated in SI units are to be regarded as the standard. The values given in parenthesis are provided for information only. 1.7  The Committee with jurisdiction for this standard is not aware of any comparable standards published by other organizations. 1.8  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.9  The committee with jurisdiction over this standard is not aware of any comparable standards published by other organizations. 1.10  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Use of Joint Sealants

ASTM C1021-08(2023) 从事建筑密封剂测试的实验室的标准实施规程

1.1  This practice describes the qualifications, including minimum requirements for personnel and equipment, duties, responsibilities, and services of independent commercial materials testing laboratories engaged in the testing of caulking and sealants used in building construction. 1.2  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.3  The subcommittee with jurisdiction of this standard is not aware of any similar or equivalent ISO standard. 1.4  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Laboratories Engaged in Testing of Building Sealants

ASTM C782-13(2023) 预成型胶带密封剂柔软度的标准试验方法

1.1  This test method describes a laboratory procedure for determining the softness of preformed tape sealants. Note 1:  Cone penetration methods applicable to greases and to petrolatum are described in Test Methods D217 and D937 . Test Method D2451 also uses a penetration technique for determining the degree of set in sash glazing compounds. 1.2  The values stated in SI units are to be regarded as standard. Temperature values are also provided (in parentheses) in degrees Fahrenheit. 1.3  The subcommittee with jurisdiction is not aware of any similar ISO standard. 1.4  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Softness of Preformed Tape Sealants

ASTM C834-17(2023) 乳胶密封剂标准规范

1.1  This specification covers one component latex sealants used for sealing joints in building construction. 1.2  A sealant meeting the requirements of this specification shall be classified by the manufacturer to be one of the types and grades defined in Section 4 . 1.3  The values stated in SI units are to be regarded as the standard. The inch-pound in parenthesis are provided for information purposes only. 1.4  The following precautionary caveat pertains only to the test method portion, Section 10 , of this Specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Note 1:  Currently, there is no ISO standard similar to this specification. 1.5  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Latex Sealants

ASTM D6496/D6496M-23a 测定针刺土工合成粘土衬里顶层和底层之间平均粘合剥离强度的标准试验方法

1.1  This test method covers the laboratory determination of the average bonding strength between the top and bottom layers of a sample of a geosynthetic clay liner (GCL). 1.2  The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.3  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determining Average Bonding Peel Strength Between Top and Bottom Layers of Needle-Punched Geosynthetic Clay Liners

KS M 2458-2023 石油产品和相关产品.用动态剪切流变仪测定沥青的多重应力蠕变和恢复（MSCR）

Petroleum products and related products — Determination of multiple stress creep and recovery (MSCR) of asphalt using a dynamic shear rheometer

GSO 549:2023 沥青材料的取样方法

This standard is concerned with the standard methods that apply to procedures for obtaining representative samples of asphalt materials whether in liquid, semi-liquid or solid form. Sampling may be carried out at manufacture, distribution or storage sites. Sampling shall be carried out by the methods mentioned later for the purpose of representing a medium quantity of a certain volume of the materials from which sampling is to be made. This is in order to determine, as far as possible, the maximum possible change that can occur on the material properties. Note (1): This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Methods of sampling bituminous materials