93.030 外部污水排放系统 标准查询与下载
共找到 509 条与 外部污水排放系统 相关的标准，共 34 页
本标准规定了聚乙烯（PE）生活污水处理池产品的型号与结构、原料要求、技术要求、试验方法、检验规则、标志、使用说明书、包装、运输和贮存。 本标准适用于以聚乙烯（PE）树脂为主要原料，主体结构经滚塑一次性成型的聚乙烯(PE)生活污水处理池。
Polyethylene (PE) Domestic Sewage Treatment Pool
- ICS
- 93.030
- CCS
- P41
- 发布
- 2014-03-04
- 实施
- 2014-06-05
Plastics piping systems for drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) - Manholes and inspection chambers; German version EN 15383:2012+A1:2013
- ICS
- 93.030
- CCS
- P41
- 发布
- 2014-02
- 实施
1.1 This specification covers requirements and test methods for annular, corrugated profile wall polyethylene pipe and fittings with an interior liner. The nominal inside diameters covered are 12 to 60 in. [300 to 1500 mm]. 1.2 The requirements of this specification are intended to provide pipe and fittings suitable for underground use for gravity-flow storm sewer and subsurface drainage systems. Note 1: Pipe and fittings produced in accordance with this specification shall be installed in compliance with Practice D2321. 1.3 This specification covers pipe and fittings with an interior liner using a corrugated exterior profile (Fig. 1). 1.4 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.5 The following precautionary caveat pertains only to the test method portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Specification for 12 to 60 in. [300 to 1500 mm] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Gravity-Flow Storm Sewer and Subsurface Drainage Applications
- ICS
- 93.030
- CCS
- 发布
- 2014
- 实施
1.1 This specification covers requirements and test methods for annular, corrugated profile wall polyethylene pipe and fittings with an interior liner. The nominal inside diameters covered are 12 to 60 in. [300 to 1500 mm]. 1.2 The requirements of this specification are intended to provide pipe and fittings suitable for underground use for gravity-flow storm sewer and subsurface drainage systems. Note 1: Pipe and fittings produced in accordance with this specification shall be installed in compliance with Practice D2321. 1.3 This specification covers pipe and fittings with an interior liner using a corrugated exterior profile (Fig. 1). 1.4 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.5 The following precautionary caveat pertains only to the test method portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Specification for 12 to 60 in. [300 to 1500 mm] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Gravity-Flow Storm Sewer and Subsurface Drainage Applications
- ICS
- 93.030
- CCS
- 发布
- 2014
- 实施
This European Standard applies to a) manholes, when made from glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP); b) inspection chambers, when made from glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) which are intended to be used with inverts which are at a depth not exceeding 2 m. These products are intended to be used within a drain or sewer system operating without pressure or occasionally at a head of pressure up to 1 bar. It applies to products, and their joints, intended for use in buried installations and to be installed by open-trench techniques. The units have a circular shape with nominal sizes not exceeding the maximum nominal size specified in EN 14364. The intended use of these products is to provide access to, buried drain or sewer systems for the conveyance of waste water at temperatures up to 50 °C, without pressure or occasionally at a head of pressure up to 1 bar, outside buildings and installed in areas subjected to vehicle and/or pedestrian traffic. It specifies definitions including symbols, requirements and characteristics of manholes, inspection chambers, joints, materials, test methods and marking. NOTE It is the responsibility of the purchaser or specifier to make the appropriate selections, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
Plastics piping systems for drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) - Manholes and inspection chambers
- ICS
- 93.030
- CCS
- 发布
- 2013-10
- 实施
Vitrified clay pipe systems for drains and sewers - Part 2: Evaluation of conformity and sampling
- ICS
- 93.030
- CCS
- 发布
- 2013-07-31
- 实施
- 2013-07-31
Vitrified clay pipe systems for drains and sewers - Part 4: Requirements for adaptors, connectors and flexible couplings
- ICS
- 93.030
- CCS
- 发布
- 2013-07-31
- 实施
- 2013-07-31
Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 4: Guidance for the assessment of conformity; German
- ICS
- 93.030
- CCS
- Q81
- 发布
- 2013-07
- 实施
Vitrified clay pipe systems for drains and sewers - Part 2: evaluation of conformity and sampling
- ICS
- 93.030
- CCS
- P41
- 发布
- 2013-05-17
- 实施
- 2013-05-17
Plastics piping systems for drainage and sewerage with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Specifications for pipes, fittings and joints; German version EN 14364:2013
- ICS
- 93.030
- CCS
- P94
- 发布
- 2013-05
- 实施
Vitrified clay pipe systems for drains and sewers - Part 2: Evaluation of conformity and sampling; German version EN 295-2:2013
- ICS
- 93.030
- CCS
- Q81
- 发布
- 2013-05
- 实施
Vitrified clay pipe systems for drains and sewers - Part 7: Requirements for pipes and joints for pipe jacking; German version EN 295-7:2013
- ICS
- 93.030
- CCS
- Q81
- 发布
- 2013-05
- 实施
Vitrified clay pipe systems for drains and sewers - Part 5: Requirements for perforated pipes and fittings; German version EN 295-5:2013
- ICS
- 93.030
- CCS
- Q81
- 发布
- 2013-05
- 实施
Vitrified clay pipe systems for drains and sewers - Part 1: Requirements for pipes, fittings and joints; German version EN 295-1:2013
- ICS
- 93.030
- CCS
- P41
- 发布
- 2013-05
- 实施
Vitrified clay pipe systems for drains and sewers - Part 6: Requirements for components of manholes and inspection chambers; German version EN 295-6:2013
- ICS
- 93.030
- CCS
- P41
- 发布
- 2013-05
- 实施
Prefabricated concrete manholes, unreinforced, steel fibre and reinforced - Part 2: Manholes for well construction and drain construction
- ICS
- 93.030
- CCS
- Q13
- 发布
- 2013-05
- 实施
Vitrified clay pipe systems for drains and sewers - Part 4: Requirements for adaptors, connectors and flexible couplings; German version EN 295-4:2013
- ICS
- 93.030
- CCS
- Q81
- 发布
- 2013-05
- 实施
Plastics piping systems for drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) - Manholes and inspection chambers
- ICS
- 93.030
- CCS
- 发布
- 2013-04-16
- 实施
- 2013-04-16
Plastics piping systems for drainage and sewerage with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Specifications for pipes, fittings and joints
- ICS
- 93.030
- CCS
- P41
- 发布
- 2013-04-06
- 实施
- 2013-04-06
