E20 石油、天然气综合 标准查询与下载

ISO 20815:2008 石油、石化和天然气工业.生产保证和可靠性管理

Petroleum, petrochemical and natural gas industries - Production assurance and reliability management

ASTM D4007-08 离心法(实验室方法)测定原油中水和沉积物的标准试验方法

The water and sediment content of crude oil is significant because it can cause corrosion of equipment and problems in processing. A determination of water and sediment content is required to measure accurately net volumes of actual oil in sales, taxation, exchanges, and custody transfers. It is not anticipated that this test method, which is written with a dedicated laboratory facility in mind, is likely to be used in field test rooms or sample rooms due to safety concerns for proper ventilation nbsp;nbsp;nbsp;and handling.1.1 This test method describes the laboratory determination of water and sediment in crude oils by means of the centrifuge procedure. This centrifuge method for determining water and sediment in crude oils is not entirely satisfactory. The amount of water detected is almost always lower than the actual water content. When a highly accurate value is required, the revised procedures for water by distillation, Test Method D 4006 (API MPMS Chapter 10.2) (Note 1), and sediment by extraction, Test Method D 473 (API MPMS Chapter 10.1), shall be used. Note 18212;Test Method D 4006 (API MPMS Chapter 10.2) has been determined to be the preferred and most accurate method for the determination of water. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific warning statements appear in 6.1, 8.3, and A1.5.4.

Standard Test Method for Water and Sediment in Crude Oil by the Centrifuge Method (Laboratory Procedure)

KS B ISO 13534:2007 石油和天然气工业.钻井和生产设备.提升设备的检查、维护、修理和再制造

이 규격은 천공 및 생산 작업과 장비의 정비성을 유지하기 위해 인양 장비의 점검, 유지보수

Petroleum and natural gas industries-Drilling and production equipment-Inspection, maintenance, repair and remanufacture of hoisting equipment

KS B ISO 13535:2007 石油和天然气工业.钻井和生产设备.提升设备

이 규격은 천공 및 생산 작동에 사용하는 적합한 설계, 제작 및 인양장치의 시험에 대한 요

Petroleum and natural gas industries－Drilling and production equipment－Hoisting equipment

CSA ISO 19904-1-07-CAN/CSA:2007 石油和天然气产业 浮动式海上结构.第1部分:单体船、半潜式平台与平台.第1版

L'Assochtion canadienne de normallsatlon (CSA), sous les auspices de laquelle cette Nonne nationale a été pAparée, a repi ses lettres patentes en 191 9 et son accréditation au sein du Système de normes nationales par le Conseil canadien des namies en 197

Petroleum and natural gas industries ?Floating offshore structures ?Part 1: Monohulls, semi-submersibles and spars First Edition

CSA ISO 19901-7-07-CAN/CSA:2007 石油和天然气产业 海上结构的特殊要求.第7部分:浮动式海上建筑物和浮动式海上设备的定位系统.第1版

A general instruction of sheet will accompany replacement pages each time they are issued and list the laste of each page of the standar.

Petroleum and natural gas industries ?Specific requirements for offshore structures ?Part 7: Stationkeeping systems for floating offshore structures and mobile offshore units First Edition

KS B ISO 15590-1:2006 石油和天然气工业.管道输送系统用诱导弯头、管件和法兰.第1部分:诱导弯头

이 규격은 ISO 13623에 정의된 석유 및 천연가스 산업에서 배관수송시스템용 유도 굽힘

Petroleum and natural gas industries－Induction bends,fittings and flanges for pipeline transportation systems－Part 1：Induction bends

KS B ISO 15590-3:2006 石油和天然气工业.管道输送系统用进气弯头、管件和法兰.第3部分:法兰

이 규격은 앵커 스위블링(swivel-ring) 플랜지와 오리피스(orifice) 플랜지뿐

Petroleum and natural gas industries-Induction bends, fittings and flanges for pipeline transportation systems-Part 3:Flanges

KS B ISO 15590-2:2006 石油和天然气工业.管道输送系统用进气弯管、管件和法兰.第2部分:管件

이 규격은 ISO 13623에 정의된 석유 및 천연가스 산업에서 배관수송계통에서 비합금 또

Petroleum and natural gas industries－Induction bends, fittings and flanges for pipeline transportation systems－Part 2：Fittings

KS I ISO 6326-5:2006 天然气.硫化物的测定.第5部分:林格聂尔燃烧法

이 규격은 천연가스 내 총 황의 측정을 위한 방법을 규정한다. 이 방법은 0.5~1 000

Natural gas－Determination of sulfur compounds－Part 5：Lingener combustion method

CSA ISO 19901-1-06-CAN/CSA:2006 石油和天然气产业 海上结构的特殊要求.第1部分:海上建筑物的特殊要求.第1版

This standard specifies general and safety requirements for electronic ballasts for use on a.c. supplies up to 1 O00 V at 50 Hz or 60 Hz with operating frequencies deviating from the supply frequency, associated with tubular fluorescent lamps as specifi

Petroleum and natural gas industries Specific requirements for offshore structures Part 1: Metocean design and operating considerations First Edition

EN ISO 16708:2006 石油和天然气工业.管道输送系统.基于可靠性的极限状态法（ISO16708:2006）

Petroleum and natural gas industries - Pipeline transportation systems - Reliability-based limit state methods

CSA ISO 19901-4-06-CAN/CSA:2006 石油和天然气产业 海上结构的特殊要求.第4部分:土工和地基设计考虑.第1版.

L'Assochtion canadienne de normallsatlon (CSA), sous les auspices de laquelle cette Nonne nationale a été pAparée, a repi ses lettres patentes en 191 9 et son accréditation au sein du Système de normes nationales par le Conseil canadien des namies en 197

Petroleum and natural gas industries Specific requirements for offshore structures Part 4: Geotechnical and foundation design considerations First Edition

EN 14870-3:2006 石油和天然气工业.诱导弯头,管道运输系统管件和法兰.第3部分:法兰盘（ISO15590-3:2004,修改）

Petroleum and natural gas industries - Induction bends@ fittings and flanges for pipeline transportation systems - Part 3: Flanges

CSA ISO 19900-06-CAN/CSA:2006 石油和天然气产业 海上结构的通用要

L’Association canadienne de normalisation (CSA) élabore des normes sous le nom Association canadienne de normalisation et offre des services de certification et de mise à l’essai sous le nom CSA International. CSA International offre des services de cer

Petroleum and natural gas industries General requirements for offshore structures First Edition; ISO 19900:2002

ASTM D3712-05(2011) 液体色谱法分析油溶性石油磺酸盐的标准试验方法

This test method provides a means of determining sulfonate content and of classifying and characterizing natural and synthetic petroleum sulfonate products by sulfonate content and average molecular weight. Purity of sodium sulfonate products is measured by basicity and inorganic salt contents and the reserve alkalinity of alkaline earth sulfonates by the total base number.1.1 This test method covers the analysis of refined and crude natural and synthetic oil-soluble sulfonate products. Resins, if present, are recovered with the oil phase and carboxylates are recovered as sulfonates. 1.2 This test method covers the determination of mineral oil, sodium sulfonate, inorganic salts, water, basicity or acidity, average molecular weight, and relative density of sodium sulfonate products. 1.3 This test method covers the determination of mineral oil, sulfonate, water, base number, average molecular weight, and relative density of calcium, barium, magnesium, and ammonium sulfonate products. 1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method of Analysis of Oil-Soluble Petroleum Sulfonates by Liquid Chromatography

ASTM D3712-05 液相色谱法分析油溶性石油磺酸盐的标准试验方法

This test method provides a means of determining sulfonate content and of classifying and characterizing natural and synthetic petroleum sulfonate products by sulfonate content and average molecular weight. Purity of sodium sulfonate products is measured by basicity and inorganic salt contents and the reserve alkalinity of alkaline earth sulfonates by the total base number.1.1 This test method covers the analysis of refined and crude natural and synthetic oil-soluble sulfonate products. Resins, if present, are recovered with the oil phase and carboxylates are recovered as sulfonates.1.2 This test method covers the determination of mineral oil, sodium sulfonate, inorganic salts, water, basicity or acidity, average molecular weight, and relative density of sodium sulfonate products.1.3 This test method covers the determination of mineral oil, sulfonate, water, base number, average molecular weight, and relative density of calcium, barium, magnesium, and ammonium sulfonate products.1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method of Analysis of Oil-Soluble Petroleum Sulfonates by Liquid Chromatography

ASTM D3230-05 原油中含盐量的标准试验方法(电测法)

1.1 This test method covers the determination of the approximate chloride (salts) concentration in crude oil. The range of concentration covered is 0 to 500 mg/kg or 0 to 150 lb/1000 bbl as chloride concentration/volume of crude oil.1.2 This test method measures conductivity in the crude oil due to the presence of common chlorides, such as sodium, calcium, and magnesium. Other conductive materials may also be present in the crude oil.1.3 The values stated in SI units are to be regarded as standard. Acceptable concentration units are g/m3 or PTB (lb/1000 bbl).This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see , , and .

Standard Test Method for Salts in Crude Oil (Electrometric Method)

ASTM D3230-05a 原油中含盐量的标准试验方法(电测法)

1.1 This test method covers the determination of the approximate chloride (salts) concentration in crude oil. The range of concentration covered is 0 to 500 mg/kg or 0 to 150 lb/1000 bbl as chloride concentration/volume of crude oil.1.2 This test method measures conductivity in the crude oil due to the presence of common chlorides, such as sodium, calcium, and magnesium. Other conductive materials may also be present in the crude oil.1.3 The values stated in SI units are to be regarded as standard. Acceptable concentration units are g/m3 or PTB (lb/1000 bbl).This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see , , and .

Standard Test Method for Salts in Crude Oil (Electrometric Method)

ASTM D3712-05(2017) 采用液相色谱法分析油溶性石油磺酸盐的标准试验方法

5.1 This test method provides a means of determining sulfonate content and of classifying and characterizing natural and synthetic petroleum sulfonate products by sulfonate content and average molecular weight. Purity of sodium sulfonate products is measured by basicity and inorganic salt contents and the reserve alkalinity of alkaline earth sulfonates by the total base number. 1.1 This test method covers the analysis of refined and crude natural and synthetic oil-soluble sulfonate products. Resins, if present, are recovered with the oil phase and carboxylates are recovered as sulfonates. 1.2 This test method covers the determination of mineral oil, sodium sulfonate, inorganic salts, water, basicity or acidity, average molecular weight, and relative density of sodium sulfonate products. 1.3 This test method covers the determination of mineral oil, sulfonate, water, base number, average molecular weight, and relative density of calcium, barium, magnesium, and ammonium sulfonate products. 1.4 The values stated in SI units are to be regarded as the standard. 1.4.1 Exception—The values given in parentheses are for information only. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method of Analysis of Oil-Soluble Petroleum Sulfonates by Liquid Chromatography