E34 润滑油 标准查询与下载

GB 5904-1986 轻负荷喷油回转式空气压缩机油

本标准适用于以矿物油馏分经各种精制工艺，并加有抗氧、抗泡和防锈等添加剂调制而成的轻负荷喷油回转式空气压缩机油。

Lubricants for light duty rotary oil-flooded air compressor

GB/T 3142-1982 润滑剂承载能力测定法(四球法)

本方法适用于在四球极压试验机上评定润滑剂的承载能力，包括最大无卡咬负荷P，烧结负荷P，综合磨损值ZMZ三项指标。在实际应用中，可根据润滑剂的各种不同用途选用不同的评定指标。 注：①最大无卡咬负荷俗称P点（代表油膜强度）。 ②综合磨损值ZMZ又称综合磨损指标，平均赫芝负荷，负荷磨损指数。

Lubricants--Determination of load carrying capacity(four balls method)

GB 3142-1982 润滑剂承载能力测定法 (四球法)

Lubricants—determination of load-carrying capacity (four balls mehtod)

GB 440-1977 20号航空润滑油

本标准适用于经过溶剂精制过程制得的航空润滑油。本产品是按国家试车通过的试样所采用的原料和生产工艺进行生产的。其代号为HH-20。

Aviation lubricating oil No.20

GB/T 391-1977 发动机润滑油腐蚀度测定法

本方法适用于测定发动机润滑油的腐蚀度，它是沾附在金属片表面的热润滑油薄膜与周围空气中氧定期接触时，所引起的金属腐蚀现象。金属片在热至140℃的试样中，经50小时的试验后，依金属片的重量变化确定试样的腐蚀度，以克/米2表示。非经另行规定，金属片材料为铅。

Determination of corrosion of engine lubricating oils

HS/T 78-2023 烃类润滑油类型的验证方法

Verification methods for hydrocarbon lubricant types

HS/T 75-2023 石油润滑剂中矿物油含量测定

Determination of mineral oil content in petroleum lubricants

T/CAPE 12003-2021 油气润滑油

Oil and gas lubricating oil

T/CAPE 12002-2021 气柜密封油

Gas cabinet seal oil

NF T60-135-1*NF ISO 11007-1:2021 石油产品和润滑剂. 润滑脂防锈性能的测定. 第1部分: 动态潮湿条件

Petroleum products and lubricants - Determination of rust-prevention characteristics of lubricating greases - Part 1 : dynamic wet conditions

ISO 11009:2021 石油产品和润滑剂. 润滑脂抗水淋特性的测定

This document specifies a method for evaluating the resistance of a lubricating grease to washout by water from a bearing, when tested at 38 °C or 79 °C under specified laboratory test conditions. This test method estimates the resistance of greases to washout from ball bearings under specified conditions. No formal correlation with field service has been established so far. This document is used for development and specification purposes. NOTE For the purposes of this document, the term “% (m/m)” is used to represent the mass fraction.

Petroleum products and lubricants - Determination of water washout characteristics of lubricating greases

ISO/TS 11007-2:2021 石油产品和润滑剂. 润滑脂防锈性能的测定. 第2部分: 水洗法

Petroleum products and lubricants - Determination of rust-prevention characteristics of lubricating greases - Part 2: Method with water wash-out

ISO 11007-1:2021 石油产品和润滑剂. 润滑脂防锈性能的测定. 第1部分: 动态潮湿条件

This document specifies a method for the determination of the rust prevention characteristics of lubricating grease under dynamic wet conditions. This test method is used to assess the ability of a grease to prevent corrosion in rolling bearings operated in presence of water, synthetic sea water or any industrial aqueous pollutant. NOTE For the purposes of this document, the term “% (m/m)” is used to represent the mass fraction.

Petroleum products and lubricants - Determination of rust-prevention characteristics of lubricating greases - Part 1: Dynamic wet conditions

HG/T 5681～5682-2020 绿色设计产品评价技术规范 农药制剂和水性建筑涂料（2020）

Green Design Product Evaluation Technical Specifications for Pesticide Formulations and Waterborne Architectural Coatings (2020)

ASTM D4683-20 在150℃高剪切速率和高温下用锥形轴承模拟器粘度计测量新的和用过的发动机油粘度的标准试验方法

1.1 This test method covers the laboratory determination of the viscosity of engine oils at 150 °C and 1.0·106 s−1 using a viscometer having a slightly tapered rotor and stator called the Tapered Bearing Simulator (TBS) Viscometer.2 1.2 The Newtonian calibration oils used to establish this test method range from approximately 1.2 mPa·s to 7.7 mPa·s at 150 °C. The precision has only been determined for the viscosity range 1.47 mPa·s to 5.09 mPa·s at 150 °C for the materials listed in the precision section. 1.3 The non-Newtonian reference oil used to establish the shear rate of 1.0·106 s−1 for this test method has a viscosity closely held to 3.55 mPa·s at 150 °C by using the absolute viscometry of the TBS. 1.4 Manual, semi-automated, and fully automated TBS viscometers were used in developing the precision statement for this test method. 1.5 Application to petroleum products such as base oils and formulated engine oils was determined in preparing the viscometric information for this test method. 1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6.1 This test method uses the milliPascal·second (mPa·s) as the unit of viscosity. This unit is equivalent to the centipoise (cP). 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides a

Standard Test Method for Measuring Viscosity of New and Used Engine Oils at High Shear Rate and High Temperature by Tapered Bearing Simulator Viscometer at 150℃

NB/SH/T 0987-2019 高频线性振动（SRV）标准试验件磨损体积测定法

High-frequency linear vibration (SRV) standard test piece wear volume determination method

NB/SH/T 0976-2019 发动机油氧化安定性的测定 ROBO试验法

Determination of oxidation stability of engine oil ROBO test method

NB/SH/T 0983-2019 传动系统润滑油低温黏度的测定 恒剪切应力黏度计法

Determination of Low Temperature Viscosity of Transmission System Lubricant by Constant Shear Stress Viscometer Method

DIN 51517-3:2018 润滑剂.润滑油.第3部分:润滑油CLP的最低要求

This document specifies minimum requirements for lubricating oils CLP which are primarily used for circulation and dip lubricating systems.

Lubricants - Lubricating oils - Part 3: Lubricating oils CLP, Minimum requirements

DIN 51517-1:2018 润滑剂. 润滑油. 第1部分:润滑油C, 最低要求

This document specifies minimum requirements for type C lubricating oils which are primarily used for circulation and dip lubricating systems.

Lubricants - Lubricating oils - Part 1: Lubricating oils C, Minimum requirements