E34 润滑油 标准查询与下载
共找到 1582 条与 润滑油 相关的标准，共 106 页
This document specifies minimum requirements for type C lubricating oils which are primarily used for circulation and dip lubricating systems.
Lubricants - Lubricating oils - Part 1: Lubricating oils C, Minimum requirements
- ICS
- 75.100
- CCS
- E34
- 发布
- 2018-09-00
- 实施
This document specifies procedures for the measurement of the extreme pressure (EP) and anti-wear properties of liquid lubricants (categories C, D, F, G, H, M, P of ISO 6743-99), lubricating greases (ISO 6743-9, category X) and other consistent lubricants. The test conditions are not intended to simulate particular service conditions, but to provide information over a range of standard conditions for the purpose of research, development, quality control and fluid ranking. The output is used in lubricant specifications.
Petroleum and related products - Determination of the extreme-pressure and anti-wear properties of lubricants - Four-ball method (European conditions) (ISO 20623:2017); German version EN ISO 20623:2018
- ICS
- 75.100
- CCS
- E34
- 发布
- 2018-04-01
- 实施
Petroleum and related products. Determination of the extreme-pressure and anti-wear properties of lubricants. Four-ball method (European conditions)
- ICS
- 75.100
- CCS
- E34
- 发布
- 2018-02-19
- 实施
- 2018-02-19
This document establishes the detailed classification of fluids of Family C (gear systems) which belongs to class L (lubricants, industrial oils and related products). It can be read in conjunction with The classification in this document concerns lubricants for industrial gears and excludes lubricants for automotive gears.
Lubricants, industrial oils and related products (class L) - Classification - Part 6: Family C (gear systems)
- ICS
- 75.100
- CCS
- E34
- 发布
- 2018-01-01
- 实施
This document establishes the specifications relative to family C (gears) for lubricants, industrial oils and related products of Class L (see ISO 6743-6). This document deals only with lubricants for enclosed gear systems. Lubricants for open gears and greases for gears (enclosed or open) are not covered. This document can be read in conjunction with ISO 6743-6. The following categories specified in
Lubricants, industrial oils and related products (class L) - Family C (gears) - Part 1: Specifications for lubricants for enclosed gear systems
- ICS
- 75.100
- CCS
- E34
- 发布
- 2018-01-01
- 实施
Evaluation method for engine oil's ability to emulsify water and simulated Ed85 fuel
- ICS
- ICS75.100
- CCS
- E34
- 发布
- 2017-12-27
- 实施
- 2018-06-01
Determination of anti-wear properties of lubricants FE8 rolling bearing wear tester method Part 1: Lubricating oils
- ICS
- ICS75.100
- CCS
- E34
- 发布
- 2017-12-27
- 实施
- 2018-06-01
Determination of hindered phenolic and aromatic amine antioxidants in zinc-free turbine oil by linear sweep voltammetry
- ICS
- ICS75.100
- CCS
- E34
- 发布
- 2017-12-27
- 实施
- 2018-06-01
This document specifies procedures for the measurement of the extreme pressure (EP) and antiwear properties of liquid lubricants (categories C, D, F, G, H, M, P of ISO 6743-99), lubricating greases simulate particular service conditions, but to provide information over a range of standard conditions for the purpose of research, development, quality control and fluid ranking. The output is used in lubricant specifications.
Petroleum and related products - Determination of the extreme-pressure and anti-wear properties of lubricants - Four-ball method (European conditions)
- ICS
- 75.100
- CCS
- E34
- 发布
- 2017-12-01
- 实施
Petroleum products. Determination of the filterability of lubricating oils. Procedure for dry oils
- ICS
- 75.100
- CCS
- E34
- 发布
- 2017-07-06
- 实施
- 2017-07-06
Petroleum products. Determination of the filterability of lubricating oils. Procedure for oils in the presence of water
- ICS
- 75.100
- CCS
- E34
- 发布
- 2017-06-29
- 实施
- 2017-06-29
Testing of lubricants - Tribological test in the translatory oscillation apparatus - Part 2: Determination of friction and wear data for lubricating oils
- ICS
- 75.100
- CCS
- E34
- 发布
- 2017-05
- 实施
This document specifies a procedure for the evaluation of the filterability of lubricating oils, particularly those designed for hydraulic applications, in the presence of water. The procedure only applies to mineral-based oils, since fluids manufactured from other materials (e.g. fire-resistant fluids) may not be compatible with the specified test membranes. The range of application has been evaluated with oils of viscosity up to ISO viscosity grade (VG) 100, as defined in ISO 3448. Within the range described, the filterability as defined is not dependent on the viscosity of the oil. The procedure is not suitable for some hydraulic oils on which specific properties have been conferred by the use of insoluble/partially soluble additives, or by particularly large molecular species. NOTE Filterability is a prime requirement for lubricating oils used in hydraulic systems because of the fine filters used in this application. This document defines a method for assessing the filterability of oils in the presence of contaminating water. It is noted that some oils will exhibit poorer filterability characteristics in these conditions. the presence of water in the oil is unlikely. An oil which has good filterability in the presence of contaminating water will not necessarily have equally good filterability in dry conditions. An oil having good filterability only when wet is unlikely to be generally acceptable.
Petroleum products - Determination of the filterability of lubricating oils - Part 1: Procedure for oils in the presence of water
- ICS
- 75.100
- CCS
- E34
- 发布
- 2017-05
- 实施
This document specifies a procedure for the evaluation of the filterability of dry lubricating oils, particularly those designed for hydraulic applications. The procedure only applies to mineral-based oils, since fluids manufactured from other materials (e.g. fire-resistant fluids) might not be compatible with the specified test membranes. The range of application has been evaluated with oils of viscosity up to ISO viscosity grade (VG) 100, as defined in ISO 3448. Within the range described, the filterability as defined is not dependent on the viscosity of the oil. The procedure is not suitable for some hydraulic oils on which specific properties have been conferred by the use of insoluble/partially soluble additives, or by particularly large molecular species. NOTE Filterability is a prime requirement for lubricating oils used in hydraulic systems because of the fine filters used in this application. This document defines a method for assessing the filterability of dry oils. It is necessary to note that some oils exhibit poorer filterability characteristics in the presence of contaminating water. an oil is used in applications where the presence of water in the oil is likely.
Petroleum products - Determination of the filterability of lubricating oils - Part 2: Procedure for dry oils
- ICS
- 75.100
- CCS
- E34
- 发布
- 2017-05
- 实施
Lubricating oils -- Determination of foaming characteristics
- ICS
- 75.100
- CCS
- E34
- 发布
- 2017-04-20
- 实施
Petroleum products - Gum content of fuels - Jet evaporation method
- ICS
- 75.160.20
- CCS
- E34
- 发布
- 2017-04
- 实施
Testing of lubricants - Sampling of lubricating oils from internal combustion engines
- ICS
- 75.100
- CCS
- E34
- 发布
- 2017-04
- 实施
Testing of lubricants - Testing rheological properties of lubricating greases - Part 1: Determination of shear viscosity by rotational viscosimeter and the system of cone/plate
- ICS
- 75.100
- CCS
- E34
- 发布
- 2017-04
- 实施
Lubricating oils -- Testing methods for load carrying capacity
- ICS
- 75.100
- CCS
- E34
- 发布
- 2017-03-21
- 实施
