G34 合成橡胶基础标准与通用方法 标准查询与下载
共找到 1828 条与 合成橡胶基础标准与通用方法 相关的标准，共 122 页
This Standard specifies a method for determining the hardness of vulcanized or thermoplastic rubber by means of a pocket hardness meter calibrated in IRHD.
Rubber, vulcanized or thermoplastic.Determination of hardness.Part 4: IRHD pocket meter method
- ICS
- 83.060
- CCS
- G34
- 发布
- 2012-03-21
- 实施
This Standard specifies a method for determining the hardness of vulcanized or thermoplastic rubber using durometers.
Rubber, vulcanized or thermoplastic -- Determination of hardness -- Part 3: Durometer method
- ICS
- 83.060
- CCS
- G34
- 发布
- 2012-03-21
- 实施
This Standard specifies the methods for determination of international rubber hardness degrees (IRHD) of vulcanized or thermoplastic rubbers.
Rubber, vulcanized or thermoplastic -- Determination of hardness -- Part 2: IRHD method (hardness between 10 IRHD and 100 IRHD)
- ICS
- 83.060
- CCS
- G34
- 发布
- 2012-03-21
- 实施
이 표준은 고무의 카본 블랙 함량 측정을 위한 열분해법(A)과 두 가지 화학적 분해법(B와
Rubber－Determination of carbon black content－Pyrolytic and chemical degradation methods
- ICS
- 83.060
- CCS
- G34
- 发布
- 2012-03-19
- 实施
- 2012-03-19
Rubber - Determination of solvent extract.
- ICS
- 83.060
- CCS
- G34
- 发布
- 2012-03-01
- 实施
- 2012-03-08
Rubber, vulcanized or thermoplastic - Determination of tensile stress-strain properties.
- ICS
- 83.060
- CCS
- G34
- 发布
- 2012-03-01
- 实施
- 2012-03-01
Rubber compounding ingredients. Organic vulcanizing agents. Determination of organic peroxide content
- ICS
- CCS
- G34
- 发布
- 2012-02-29
- 实施
- 2012-02-29
Rubber, vulcanized or thermoplastic - Determination of adhesion to metal - Two-plate method.
- ICS
- 83.060
- CCS
- G34
- 发布
- 2012-02-01
- 实施
- 2012-02-04
Rubber - Compatibility between hydraulic fluids and standard elastomeric materials.
- ICS
- 23.100.01;83.140.01
- CCS
- G34
- 发布
- 2012-02-01
- 实施
- 2012-02-11
Rubber, vulcanized or thermoplastic - Determination of compression stress-strain properties.
- ICS
- 83.060
- CCS
- G34
- 发布
- 2012-02-01
- 实施
- 2012-02-18
Rubber, vulcanized or thermoplastic - Determination of indentation hardness - Part 2: IRHD pocket meter method (ISO 7619-2:2010)
- ICS
- 83.060
- CCS
- G34
- 发布
- 2012-02
- 实施
Rubber, vulcanized or thermoplastic - Determination of indentation hardness - Part 1: Durometer method (Shore hardness) (ISO 7619-1:2010)
- ICS
- 83.060
- CCS
- G34
- 发布
- 2012-02
- 实施
Rubber, vulcanized or thermoplastic. Determination of tensile stress-strain properties
- ICS
- 83.060
- CCS
- G34
- 发布
- 2012-01-31
- 实施
- 2012-01-31
Rubber. Compatibility between hydraulic fluids and standard elastomeric materials
- ICS
- 23.100.01;83.140.01
- CCS
- G34
- 发布
- 2012-01-31
- 实施
- 2012-01-31
Rubber compounding ingredients. Sulfur. Methods of test
- ICS
- 83.040.20
- CCS
- G34
- 发布
- 2012-01-31
- 实施
- 2012-01-31
Rubber, vulcanized or thermoplastic - Determination of flex cracking and crack growth (De Mattia).
- ICS
- 83.060
- CCS
- G34
- 发布
- 2012-01-01
- 实施
- 2012-01-28
Rubber, vulcanized or thermoplastic - Determination of stress relaxation in compression - Part 1 : testing at constant temperature.
- ICS
- 83.060
- CCS
- G34
- 发布
- 2012-01-01
- 实施
- 2012-01-21
Rubber, vulcanized or thermoplastic - Determination of shear modulus and adhesion to rigid plates - Quadruple-shear methods.
- ICS
- 83.060
- CCS
- G34
- 发布
- 2012-01-01
- 实施
- 2012-01-14
3.1 This practice describes procedures to use in determining the effects of an open-flame carbon-arc light source, an enclosed carbon-arc light source, a xenon-arc light source, or a fluorescent UV source along with heat and moisture on rubber specimens held in a jig or holder with or without a specified strain. The purpose is to attempt to accelerate the effects produced by light, heat, and moisture in the natural environment. Exposures are not intended to simulate the deterioration caused by localized weather phenomena, such as atmospheric pollution, biological attack, and saltwater exposure. The Significance and Use section in Practice G151 and the standard for the appropriate apparatus, that is, Practices G152, G153, G154, or G155 should be consulted for additional information on significance and use of the exposure tests. 3.2 The primary criterion used in estimating resistance to weathering is the percentage decrease in tensile strength and in elongation at break. A supplementary criterion for estimating resistance to weathering is the observed extent of surface crazing and cracking. 3.3 Results obtained by use of these test procedures should not be represented as equivalent to those of any natural exposure test until the degree of quantitative correlation has been established for the material in question. 3.4 Because of differences in the spectral power distributions of the exposure sources as well as the other conditions in the different types of laboratory weathering tests, the different procedures may not result in the same performance rankings or types of failure modes of the materials. Comparisons shall not be made of relative stabilities of materials exposed in different types of apparatus. 3.5 When conducting exposures in devices that use laboratory light sources, it is important to consider how well the artificial weathering conditions will reproduce property changes and failure modes caused by end-use environments on the materials being tested. 3.6 Practices G151, G152, G153, G154, and G155 recommend that a similar material of known performance (a control) be exposed simultaneously with the test specimen to provide a standard for comparative purposes. Preferably, a control material known to have poor durability as well as one that has good durability should be used. The reason for using a control is that reproducibility in ranking stabilities is usually better than reproducibility of absolute changes. Therefore, the use of controls is particularly important when test materials are not being compared with one another. 1.1 This practice covers specific variations in the test conditions and procedures that shall be applicable when Practice G151 plus either Practice G152, G153, G154, or
Standard Practice for Rubber Deterioration Using Artificial Weathering Apparatus
- ICS
- 83.060
- CCS
- G34
- 发布
- 2012
- 实施
3.1 This practice describes procedures to use in determining the effects of an open-flame carbon-arc light source, an enclosed carbon-arc light source, a xenon-arc light source, or a fluorescent UV source along with heat and moisture on rubber specimens held in a jig or holder with or without a specified strain. The purpose is to attempt to accelerate the effects produced by light, heat, and moisture in the natural environment. Exposures are not intended to simulate the deterioration caused by localized weather phenomena, such as atmospheric pollution, biological attack, and saltwater exposure. The Significance and Use section in Practice G151 and the standard for the appropriate apparatus, that is, Practices G152, G153, G154, or G155 should be consulted for additional information on significance and use of the exposure tests. 3.2 The primary criterion used in estimating resistance to weathering is the percentage decrease in tensile strength and in elongation at break. A supplementary criterion for estimating resistance to weathering is the observed extent of surface crazing and cracking. 3.3 Results obtained by use of these test procedures should not be represented as equivalent to those of any natural exposure test until the degree of quantitative correlation has been established for the material in question. 3.4 Because of differences in the spectral power distributions of the exposure sources as well as the other conditions in the different types of laboratory weathering tests, the different procedures may not result in the same performance rankings or types of failure modes of the materials. Comparisons shall not be made of relative stabilities of materials exposed in different types of apparatus. 3.5 When conducting exposures in devices that use laboratory light sources, it is important to consider how well the artificial weathering conditions will reproduce property changes and failure modes caused by end-use environments on the materials being tested. 3.6 Practices G151, G152, G153, G154, and G155 recommend that a similar material of known performance (a control) be exposed simultaneously with the test specimen to provide a standard for comparative purposes. Preferably, a control material known to have poor durability as well as one that has good durability should be used. The reason for using a control is that reproducibility in ranking stabilities is usually bett............
Standard Practice for Rubber Deterioration Using Artificial Weathering Apparatus
- ICS
- 83.060 (Rubber)
- CCS
- G34
- 发布
- 2012
- 实施
