共找到 1828 条与 合成橡胶基础标准与通用方法 相关的标准,共 122 页
Butadiene rubber (BR) -- Solution-polymerized types -- Evaluation procedures
This document specifies two methods for determining, by measurement of the transmission rate, the permeability of rubber to volatile liquids diffusing into open air.
Rubber, vulcanized or thermoplastic - Rubber sheets and rubber-coated fabrics - Determination of transmission rate of volatile liquids (gravimetric technique) (ISO 6179:2017); German version EN ISO 6179:2017
Rubber, vulcanized or thermoplastic. Determination of compression stress-strain properties
This document specifies a method for the determination of the tensile stress-strain properties of vulcanized and thermoplastic rubbers. The properties which can be determined are tensile strength, elongation at break, stress at a given elongation, elongation at a given stress, stress at yield and elongation at yield. The measurement of stress and strain at yield applies only to some thermoplastic rubbers and certain other compounds.
Rubber, vulcanized or thermoplastic - Determination of tensile stress-strain properties
This document specifies three methods for the determination of the soap and organic-acid content of raw styrene-butadiene rubber (SBR). — Method A is the titration method using indicator reagent. — Method B is the titration method using an automatic potentiometric titrator. — Method C is the back titration method using an automatic potentiometric titrator. Since the soaps and organic acids present in the rubber are not single chemical compounds, the method gives only an approximate value for the soap and organic-acid content.
Styrene-butadiene rubber, raw - Determination of soap and organic-acid content
Rubber, vulcanized or thermoplastic -- Determination of low-temperature properties -- Part 2: Low-temperature brittleness
Rubber, vulcanized or thermoplastic -- Determination of low-temperature properties -- Part 4: Low-temperature retraction (TR test)
Rubber, vulcanized or thermoplastic -- Determination of heat ageing properties
Rubber, vulcanized or thermoplastic -- Determination of low-temperature properties -- Part 3: Low temperature stiffening (Gehman test)
Rubber, vulcanized or thermoplastic -- Determination of low-temperature properties -- Part 1: General introduction and guide
This document specifies methods for the determination of the compression stress-strain properties of vulcanized or thermoplastic rubber using a standard test piece, a product or a part of a product. Four procedures are given: — using standard test piece A with the metal plates lubricated (method A); — using standard test piece A with the metal plates bonded to the test piece (method B); — using standard test piece B (method C); — using a product or a part of a product with the metal plates lubricated (method D). The methods are not suitable for materials that exhibit high set.
Rubber, vulcanized or thermoplastic - Determination of compression stress-strain properties
Rubber, vulcanized or thermoplastic. Determination of abrasion resistance using a rotating cylindrical drum device
Rubber, vulcanized or thermoplastic. Determination of low-temperature brittleness
Rubber, vulcanized. Determination of tension fatigue
Rubber, unvulcanized - Determinations using a shearing-disc viscometer - Part 4: Determination of the Mooney stress-relaxation rate
This document specifies two methods for the determination of the resistance of rubber to abrasion by means of a rotating cylindrical drum device. The methods involve determination of the volume loss due to the abrasive action of rubbing a test piece over a specified grade of abrasive sheet. Method A is for a non-rotating test piece and method B is for a rotating test piece. For each method, the result can be reported as a relative volume loss or an abrasion resistance index. These test methods are suitable for comparative testing, quality control, specification compliance testing, referee purposes and research and development work. No close relation between the results of this abrasion test and service performance can be inferred. NOTE The abrasion loss is often more uniform using the rotating test piece because the whole surface of the test piece is in contact with the abrasive sheet over the duration of the test. However, there is considerable experience using the non-rotating test piece.
Rubber, vulcanized or thermoplastic - Determination of abrasion resistance using a rotating cylindrical drum device
Rubber, vulcanized or thermoplastic. Determination of flex cracking and crack growth (De Mattia)
Rubber, vulcanized. Determination of stress in tension upon heating
Rubber, vulcanized. Determination of adhesion to wire cord
Rubber, vulcanized or thermoplastic. Determination of adhesion to metal. Two-plate method
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号