G43 橡胶密封件 标准查询与下载

HG/T 2579-1994 Ｏ形圈橡胶材料 第1部分：用于普通液压系统

本标准规定了普通液压系统石油基液压油和润滑油(脂)用O形圈橡胶材料的分类、技术要求、试验方法，检验规则及标志、包装、运输、贮存的要求。 本标准适用于普通液压系统石油基液压油和润滑油(脂)，工作温度范围分别为-40～+100℃和-25～+125℃的O形圈橡胶材料。

O-ring rubber materials - Part 1: For general hydraulic systems

ASTM D1414-94(2008) O形橡胶密封圈的标准试验方法

These test methods provide acceptable procedures for quality control purposes and for the determination of engineering characteristics. 1.1 These test methods describe the procedures for determining the physical properties of O-rings and changes in these properties due to aging. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Rubber O-Rings

ASTM D1414-94(2003) O型橡胶圈的标准试验方法

These test methods provide acceptable procedures for quality control purposes and for the determination of engineering characteristics. 1.1 These test methods describe the procedures for determining the physical properties of O-rings and changes in these properties due to aging. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Rubber O-Rings

ASTM D1414-94(2013) O形橡胶密封圈的标准试验方法

4.1 These test methods provide acceptable procedures for quality control purposes and for the determination of engineering characteristics. 1.1 These test methods describe the procedures for determining the physical properties of O-rings and changes in these properties due to aging. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Rubber O-Rings

SAE AMS7257C-1993 耐高温流体70-80的全氟碳化(FFKM)橡胶密封环

This specification covers a perfluorocarbon (FFKM) rubber in the form of molded o-rings. These sealing rings have been used typically in applications in contact with air or a variety of fuels, lubricants and hydraulic fluids from -15 to +290 degrees C (+5 to 554 degrees F), but usage is not limited to such applications. Each application, however, has to be considered individually. Instances are known when these rings have been used below -15 degrees C (+5 degrees F) and above 290 degrees C (554 degrees F). The cross section of such rings is usually not over 0.275 inch (6.98 mm) in diameter or thickness.

Rings, Sealing, Perfluorocarbon (FFKM) Rubber High Temperature Fluid Resistant 70 - 80

ISO 10221:1993 球墨铸铁管线.饮用水管线用橡胶密封圈

This International Standard lays down the material specifications of solid vulcanized rubber sealing rings used in ductile iron pipelines carrying potable water. It also specifies requirements for their effect on the organoleptic properties (colour, taste and odour) and the total organic carbon content of water. In the case of composite seals (which comprise, for example, both rubbers which are rigid and rubbers which are flexible), this International Standard is ap- plicable only to the requirement for their effect on the total organic carbon content of water. Cellular and closed-cell rubber seals are not covered by this International Standard. NOTE 1 This International Standard is applicable only in the absence of more stringent national standards and regu- lations.

Ductile iron pipelines; rubber sealing rings for pipelines carrying potable water

HB 6691-1993 耐磷酸酯液压油Ｏ形橡胶密封圈挡圈

本标准规定了耐磷酸酯液压油O形橡胶密封圈用的挡圈尺寸、公差及材料。 　　本标准适用于HB6692《耐磷酸酯液压油O形橡胶密封圈沟槽》中的轴、孔沟槽。

Phosphate Ester Resistant Hydraulic Oil O-Ring Rubber Seal Ring

HB 6692-1993 耐磷酸酯液压油Ｏ形橡胶密封圈沟槽

本标准规定了耐磷酸酯液压油O形橡胶密封圈（简称O形圈）密封结构形式及沟槽尺寸系列与公差。 　　本标准适用于HB6488　耐磷酸酯液压油O形橡胶密封圈。

Phosphate ester hydraulic oil resistant O-ring rubber seal groove

ASTM F434-93(2009) 预制衬垫的漏气的标准试验方法

This test method is designed to compare all types of preformed gaskets under controlled conditions with respect to blow-out resistance. This test method may be used as a routine test when agreed upon between the purchaser and the seller.1.1 This test method covers the determination of the resistance against blow-out of preformed gaskets. The test is conducted under ambient conditions and should be used for comparison purposes only to select suitable designs and constructions for specific applications. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Blow-Out Testing of Preformed Gaskets

NAVY MIL-L-82653 A-1993 聚丁二烯基内衬材料

This specification covers three types of polybutadiene base liner materials.

LINER MATERIAL, POLYBUTADIENE BASE

HG/T 2331-1992 液压隔离式蓄能器用胶囊

Capsules for Hydraulic Isolation Accumulators

HG/T 2293-1992 离合器用橡胶气胎

Rubber pneumatic tire for clutch

HG/T 2292-1992 环形防喷器胶芯

Annular blowout preventer rubber core

HG/T 2330-1992 旋转轴唇形密封圈贮存、维护和安装

Rotary shaft lip seal storage, maintenance and installation

BS EN 291:1992 压力为200毫巴及其以下的家用可燃气体静态密封用橡胶密封件的材料规范

Requirements and test methods for homogeneous rubbers used to manufacture static seals for use in domestic gas appliances.

Rubber seals - Static seals in domestic appliances for combustible gas up to 200 mbar - Specification for material

NF D36-201:1992 橡胶密封件.压力为200毫巴及其以下的家用燃气器具的静态密封件.材料规范

Rubber seals. Static seals in domestic appliances for combustibles gas up to 200 mbar. Specification for material.

EN 291:1992 压力为200毫巴及其以下的家用可燃气体静态密封用橡胶密封件的材料规范

Rubber Seals - Static Seals in Domestic Appliances for Combustible Gas up to 200 mbar - Specifications for Material

HG 2178-1991 家用煤气表橡胶膜片

本标准规定了家用煤气表橡胶膜片的分类、技术要求、试验方法、检验规则以及标志、包装、运输、贮存要求。 本标准适用于以合成纤维织物增强的家用煤气表橡胶膜片。

Household gas meter rubber diaphragm

ISO 9631:1991 橡胶密封件 温度为110℃的热水供给管道的密封件 材料规范

Rubber seals; joint rings for hot water supply pipelines up to 110 °C; specification for the material

prEN 549-1991 使用除工业过程所用以外燃气器具和有关控制钮的密封和膜片用橡胶材料

Rubber materials for seals and diaphragms for appliances and associated controls using combustible gases except those designed for use in industrial processes