G43 橡胶密封件 标准查询与下载

ASTM D3903-03 太阳能系统的热空气传递用橡胶密封件的标准规范

1.1 This specification covers the general requirements for the rubber seals used in solar energy systems employing air-heat transport. Examples are duct and damper seals. Particular applications may necessitate other requirements that would take precedence over these requirements when specified.Note 18212;Rubber seals for the collector are covered in Specifications D 3667 and D 3771.1.2 Design requirement pertains only to permissible deflections of the rubber during thermal expansion or contraction of the seal in use and the tolerances in dimensions of molded and extruded seals.1.3 This specification does not include requirements pertaining to the fabrication or installation of the seals.1.4 The values stated in SI units are to be regarded as the standard.1.5 The following safety hazards caveat pertains only to the test methods portion, Section 10, of this specification: This standard does not purport to address the safety concerns associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Rubber Seals Used in Air-Heat Transport of Solar Energy Systems

ASTM D6924-03(2012) 桥梁用预成形热塑塑性硫化橡胶弹性体接缝的标准规范

1.1 This specification covers the material requirements for preformed thermoplastic vulcanizate (TPV) elastomeric joint seals for bridges. The seal consists of a multiple-web design composed of a TPV and functions only by compression of the seal between the faces of the joint with the seal folding inward at the top to facilitate compression. The seal is installed with a lubricant adhesive and is designed to seal the joint and reject incompressibles. Note 18212;This specification may not be applicable for seals whose height is less than 90 % of its nominal width. 1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are provided for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

Standard Specification for Preformed Thermoplastic Vulcanizate Elastomeric Joint Seals for Bridges

ASTM C564-03 铸铁污水管及其管件用橡胶垫圈标准规范

1.1 This specification covers preformed rubber gaskets used to seal joints in cast iron soil pipe and fittings.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 The following safety hazards caveat pertains only to the test methods section of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.4 The committee with jurisdiction over this standard is not aware of another comparable standard for materials covered in this standard.

Standard Specification for Rubber Gaskets for Cast Iron Soil Pipe and Fittings

ASTM C564-03a 铸铁污水管及其管件用橡胶垫圈标准规范

1.1 This specification covers preformed rubber gaskets used to seal joints in cast iron soil pipe and fittings.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 The following safety hazards caveat pertains only to the test methods section of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.4 The committee with jurisdiction over this standard is not aware of another comparable standard for materials covered in this standard.

Standard Specification for Rubber Gaskets for Cast Iron Soil Pipe and Fittings

SAE AIR1707A-2003 O型密封圈失效型式

The information presented herein describes the commonly observed patterns of O-ring failure by means of both text and illustration. Possible causes and corrective actions are indicated for alleviating the problem. This document is intended to provide a guide for analyzing O-rings which have failed in order to correct the circumstances which have caused the failure. A great deal can be learned toward solving a sealing problem involving O-rings by close observation of the failed O-ring.

Patterns of O-ring Failures

NAVY MIL-S-3105 C REINST NOTICE 3-2002 用于军火的惰性封口剂

MIL-S-3105C dated 4 December 1970 is hereby reinstated and may be used for acquisition

SEALING COMPOUND, INERT (FOR USE IN AMMUNITION)

NAVY QPL-AMS-S-4383-1 (1)-2002 BUNA-N-型油箱面漆密封胶

This list has been prepared for use by or for the Government in the acquisition of products covered by the subject non-Government standard and such listing of a product is not intended to and does not connote endorsement of the product by the Department of Defense. All products listed herein have been qualified under the requirements for the product as specified in the latest adopted issue of the applicable non-Government standard. This list is subject to change without notice; revision or amendment of this list will be issued as necessary. The listing of a product does not release the manufacturer from compliance with the non-Government standard requirements.

SEALING COMPOUND, TOPCOAT, FUEL TANK, BUNA-N-TYPE

NAVY QPL-AMS-S-4383-1-2002 BUNA-N-型油箱面漆密封胶

This list has been prepared for use by or for the Government in the acquisition of products covered by the subject non-Government standard and such listing of a product is not intended to and does not connote endorsement of the product by the Department of Defense. All products listed herein have been qualified under the requirements for the product as specified in the latest adopted issue of the applicable non-Government standard. This list is subject to change without notice; revision or amendment of this list will be issued as necessary. The listing of a product does not release the manufacturer from compliance with the non-Government standard requirements.

SEALING COMPOUND, TOPCOAT, FUEL TANK, BUNA-N-TYPE

HG/T 3089-2001 燃油用O形橡胶密封圈材料

本标准规定了石油基燃油系统用O形橡胶密封圈材料的要求、抽样、试验方法及标志、标签、包装、贮存。 本标准适用于在石油基燃油系统、-40～100℃下使用的O形橡胶密封圈材料。

Rubber mixture of O-ring seals for fuel

HG/T 3096-2001 水闸橡胶密封件

本标准规定了水闸橡胶密封件的分类、要求、抽样、试验方法及标志、包装、贮存和运输。 本标准适用于水利、水电工程闸门用的橡胶密封件。

Rubber gate seals

HG/T 3087-2001 静密封橡胶零件贮存期快速测定方法

本标准适用于测定静密封橡胶零件在未变形和变形(径向压缩12%～25%，轴向压缩15%～40%)状态下，在空气和各种油介质中，在仓库贮存条件下保持工作能力的贮存期限。 本方法不适用于易水解的橡胶，例如硅橡胶、聚氨酯、丙烯酸酯和氯醇橡胶等制造的零件在其贮存时与空气接触的情况。 按照本方法测定的橡胶零件贮存期，可作为制定产品贮存期的依据之-。

Method of accelerated determination for Shelf-life of rubber static sealing parts

NAVY MIL-PRF-23586 F (2)-2002 电气用硅胶密封胶(含促进剂)

This amendment forms a part of MIL-PRF-23586F, dated 30 December 1996, and is approved for use by all Departments and Agencies of the Department of Defense.

SEALING COMPOUND (WITH ACCELERATOR), SILICONE RUBBER, ELECTRICAL [Use In Lieu Of: NAVY MIL-S-0023586 B]

ASTM C443-02 使用橡胶垫圈的混凝土管和出入口接头的标准规范

1.1 This specification covers flexible watertight joints for concrete pipe and precast manhole sections, using rubber gaskets for sealing the joints, where infiltration or exfiltration is a factor in the design. The specification covers the design of joints and the requirements for rubber gaskets to be used therewith, for pipe conforming in all other respects to Specification C 14, Specification C 76, or Specificaton C 507 and precast manhole section conforming in all other respects to Specification C 478, provided that if there is conflict in permissible variations in dimensions the requirements of this specification for joints shall govern.1.2 A complete metric companion to Specification C 443 has been developed-C 443M; therefore, no metric equivalents are presented in this specification. Note 18212;This specification covers the design, material, and performance of the rubber gasket joint only. Joints covered by this specification are normally adequate for hydrostatic pressures up to 13 psi (30 ft) without leakage, when tested in accordance with Section . Infiltration or exfiltration quantities for an installed pipeline are dependent upon many factors other than the joints, and allowable quantities must be covered by other specifications and suitable testing of the installed pipeline and system.

Standard Specification for Joints for Concrete Pipe and Manholes, Using Rubber Gaskets

ASTM C443M-02 使用橡胶垫圈作污水管和排水口的连接件的标准规范

1.1 This specification covers flexible watertight joints for concrete pipe and precast manhole sections, using rubber gaskets for sealing the joints, where infiltration or exfiltration is a factor in the design. The specification covers the design of joints and the requirements for rubber gaskets to be used therewith, for pipe conforming in all other respects to Specification C 14M, Specification C 76M, or Specification C 507 and precast manhole section conforming in all other respects to Specification C 478M, provided that if there is conflict in permissible variations in dimensions the requirements of this specification for joints shall govern.1.2 This specification is the metric counterpart of Specification C 443. Note 18212;This specification covers the design, material, and performance of the rubber gasket joint only. Joints covered by this specification are normally adequate for hydrostatic pressures up to 90 kPa (9 m) without leakage, when tested per Section . Infiltration or exfiltration quantities for an installed pipeline are dependent upon many factors other than the joints, and allowable quantities must be covered by other specifications and suitable testing of the installed pipeline and system.

Standard Specification for Joints for Concrete Pipe and Manholes, Using Rubber Gaskets (Metric)

ASTM F913-02(2008) 连接塑料管用热塑弹性密封件(垫圈)标准规范

1.1 This specification covers thermoplastic elastomeric seals (gaskets) used to seal the joints of plastic pipe and fittings used for gravity and low-pressure applications. This specification refers to push-on joints that require no internal or external pressure to effect the initial seal. 1.2 Requirements are given for thermoplastic elastomers. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 The following precautionary caveat pertains only to the test methods portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Thermoplastic Elastomeric Seals (Gaskets) for Joining Plastic Pipe

JIS K 6236:2001 乳化聚合丁苯生橡胶.结合苯乙烯含量测定.折光指数法

この規格は，原料乳化重合スチレンーブタジエンゴム(SBR)の結合スチレン量を，その抽出処理を行った試料の屈折率から，屈折率とスチレンの質量%との相関表によって求める方法について規定する。この方法は，屈折率の測定可能なフィルムが作成できる場合においては，油展の乳化重合SBRこも適合できる。溶液重合SBRには適用できない。

Rubber, raw styrene-butadiene, emulsion-polymerized -- Determination of bound styrene content -- Refractive index method

ASTM C443-01 使用橡胶垫圈的圆形混凝土污水管和涵管接头的标准规范

1.1 This specification covers flexible watertight joints for circular concrete sewer and culvert pipe and precast manhole sections, using rubber gaskets for sealing the joints, where infiltration or exfiltration is a factor in the design. The specification covers the design of joints and the requirements for rubber gaskets to be used therewith, for pipe conforming in all other respects to Specification C 14 or Specification C 76, and precast manhole section conforming in all other respects to Specification C 478, provided that if there is conflict in permissible variations in dimensions the requirements of this specification for joints shall govern.1.2 A complete metric companion to Specification C 443 has been developed-C 443M; therefore, no metric equivalents are presented in this specification. Note 18212;This specification covers the design, material, and performance of the rubber gasket joint only. Joints covered by this specification are normally adequate for hydrostatic pressures up to 13 psi (30 ft) without leakage, when tested in accordance with Section 10. Infiltration or exfiltration quantities for an installed pipeline are dependent upon many factors other than the joints, and allowable quantities must be covered by other specifications and suitable testing of the installed pipeline and system.

Standard Specification for Joints for Circular Concrete Sewer and Culvert Pipe, Using Rubber Gaskets

ASTM C443M-01 使用橡胶垫圈的圆形混凝土污水管和涵管接头的标准规范(米制)

1.1 This specification covers flexible watertight joints for circular concrete sewer and culvert pipe and precast manhole sections, using rubber gaskets for sealing the joints, where infiltration or exfiltration is a factor in the design. The specification covers the design of joints and the requirements for rubber gaskets to be used therewith, for pipe conforming in all other respects to Specification C 14M or Specification C 76M, and precast manhole section conforming in all other respects to Specification C 478M, provided that if there is conflict in permissible variations in dimensions the requirements of this specification for joints shall govern.1.2 This specification is the metric counterpart of Specification C 443. Note 18212;This specification covers the design, material, and performance of the rubber gasket joint only. Joints covered by this specification are normally adequate for hydrostatic pressures up to 90 kPa (9 m) without leakage, when tested per Section 10. Infiltration or exfiltration quantities for an installed pipeline are dependent upon many factors other than the joints, and allowable quantities must be covered by other specifications and suitable testing of the installed pipeline and system.

Standard Specification for Joints for Circular Concrete Sewer and Culvert Pipe, Using Rubber Gaskets (Metric)

BS EN 681-2:2000 弹性密封件.输水和排水用管联接密封件材料要求.热塑性弹性体

This standard specifies requirements for materials used for moulded seals only of thermoplastic elastomers (TPE) used in joints of: 1) thermoplastic piping systems for non pressure waste water discharge (intermittent flow up to 95 ℃) inside buildings; 2) thermoplastic piping systems for non-pressure underground drainage and sewerage (continuous flow up to 45 ℃ and intermittent flow up to 95 ℃); 3) thermoplastic rainwater piping systems. General requirements for finished joint seals are also given; any additional requirements called for by the particular application are specified in the relevant product standards taking into account that the performance of pipe joints is a function of the seal material properties, seal geometry and pipe joint design.

Elastomeric seals - Material requirements for pipe joint seals used in water and drainage applications - Thermoplastic elastomers

HG/T 3091-2000 橡胶密封件.给、排水管及污水管道用接口密封圈.材料规范

Rubber seals.Joint rings for water supply,drainage and sewerage pipelines.Specification for materials