H60 有色金属及其合金产品综合 标准查询与下载

YS/T 844-2017 铝合金建筑用隔热型材复合技术规范

Technical Specification for Composite Insulation Profiles for Aluminum Alloy Buildings

YS/T 591-2017 变形铝及铝合金热处理

本标准规定了变形铝及铝合金热处理的要求和质量保证措施。 本标准适用于一般工业用变形铝及铝合金产品的热处理。 变形铝及铝合金材料零部件的热处理可参照执行本标准。

Heat treatment of wrought aluminium and aluminium alloys

YS/T 1189-2017 铝及铝合金无铬化学预处理膜

Chromium-free chemical pretreatment membrane for aluminum and aluminum alloys

DB34/T 2879-2017 铜渣尾矿化学分析方法 铜含量的测定 原子吸收光谱法

本标准规定了铜渣尾矿中铜含量的测定方法。 本标准适用于铜渣尾矿中铜含量的测定。测定范围：0.100％～0.800％。

Methods for chemical analysis of copper slag tailings - Determination of copper content - Atomic absorption spectrometry

DB34/T 2878-2017 铜渣尾矿化学分析方法 铁含量的测定 重铬酸钾滴定法

本标准规定了铜渣尾矿中铁含量的测定方法。 本标准适用于铜渣尾矿中铁含量的测定。测定范围：38.00％～60.00％。

Methods for chemical analysis of copper slag tailings Determination of iron content Potassium dichromate titration method

ASTM B1007-17 焊接沉淀硬化或冷加工镍合金管的标准规格

1.1 This specification covers nominal and minimum wall-thickness welded tubes and welded and cold worked tubes made from the nickel alloys listed in Table 1. Anticipated uses cover applications where strength and strength at elevated temperatures are desired attributes. Some examples are hydraulic control lines, boilers, heat exchangers, and solar absorbers. (A) Columbium or Niobium (Nb) are references to the same element.(B) Remainder: The element may be determined arithmetically by difference.(C) Minimum: The element may be determined arithmetically by difference. 1.2 Tube shall be supplied in one of the following conditions; cold worked, cold worked and precipitation hardened, solution annealed plus precipitation hardened, or solution annealed and descaled conditions. When atmosphere control is used, descaling is not necessary. 1.3 This specification covers tube 1/8 to 6 in. (3.2 to 152.4 mm) in outside diameter and 0.015 to 0.148 in. (0.41 to 3.7 mm) inclusive in wall thickness. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Welded Precipitation Hardenable or Cold Worked, Nickel Alloy Tube

ASTM B834-17 压力强化粉末冶金铁镍铬钼(UNS N08367), 镍铬钼钶(Nb)(UNS N06625), 镍铬铁合金(UNS N06600和N06690)以及镍铬铁库仑的标准规格

1.1 This specification covers pressure consolidated powder metallurgy iron-nickel-chromium-molybdenum (UNS N08367) and nickel-chromium-molybdenumcolumbium (Nb) (UNS N06625), nickel-chromium-iron alloys (UNS N06600 and N06690), and nickel-chromium-iron-columbium (Nb)-molybdenum (UNS N07718) alloy pipe flanges, fittings, valves, and parts intended for general corrosion or heat-resisting service. 1.1.1 UNS N06625 products are furnished in two grades of different heat-treated conditions: 1.1.1.1 Grade 1 (annealed)—Material is normally employed in service temperatures up to 1100°F (593°C). 1.1.1.2 Grade 2 (solution annealed)—Material is normally employed in service temperatures above 1100°F (593°C) when resistance to creep and rupture is required. 1.2 UNS N08367 products are furnished in the solution annealed condition. 1.3 UNS N06600 products are furnished in the annealed condition. 1.4 UNS N06690 products are furnished in the annealed condition. 1.5 UNS N07718 products are furnished in the solution annealed + precipitation hardened condition. 1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.7 The following safety hazards caveat pertains only to test methods portions, Sections 7.3 and 13, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and to determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Pressure Consolidated Powder Metallurgy Iron-Nickel-Chromium-Molybdenum (UNS N08367), Nickel-Chromium-Molybdenum-Columbium (Nb) (UNS N06625), Nickel-Chromium-Iron Alloys (UNS N06600 and N06690), and Nickel-Chromium-Iron-Colum

ASTM A1002-16 镍铝有序合金铸件的标准规格

1.1 This specification covers nickel-aluminum ordered alloy castings intended for elevated-temperature applications such as heat-resisting alloy furnace rollers, supports, hangers, and so forth, in environments up to 23008201;°F (12608201;°C). 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.2.1 The SI gage length for tension test specimens is in brackets and is considered standard.

Standard Specification for Castings, Nickel-Aluminum Ordered Alloy

KS D 9401-2015 防锈.防蚀术语

Glossary of terms used in rust and corrosion preventive technology

YS/T 441.2-2014 有色金属平衡管理规范 第2部分:铅选矿冶炼

YS/T 441的本部分规定了铅选矿冶炼部分金属平衡管理的术语、管理职责、金属平衡计算公式、金属平衡表的编制方法及格式等。本部分适用于铅及其附属产品选矿冶炼生产企业。

Management rules of nonferrous metals balance.Part 2:Lead enrichment and metallurgy

YS/T 441.3-2014 有色金属平衡管理规范 第3部分:锌选矿冶炼

YS/T 441的本部分规定了锌选矿冶炼部分金属平衡管理规范的术语、管理职责、金属平衡计算公式、金属平衡表的编制方法及格式等。本部分适用于锌及其附属产品选矿冶炼生产企业。

Management rules of nonferrous metals balance.Part 3:Zinc enrichment and metallurgy

YS/T 441.1-2014 有色金属平衡管理规范 第1部分:铜选矿冶炼

YS/T 441的本部分规定了铜选矿冶炼部分金属平衡管理的术语、管理职责、金属平衡计算公式、金属平衡表的编制方法及格式等。本部分适用于铜及其附属产品选矿冶炼生产企业。

Management rules of nonferrous metals balance.Part 1:Copper enrichment and metallurgy

YS/T 441.5-2014 有色金属平衡管理规范 第5部分:金、银冶炼

YS/T 441的本部分规定了有色金属金、银冶化部分金属平衡管理的术语、管理职责、金属平衡计算公式、金属平衡表的编制方法及格式等。本部分适用于以有色金属冶金尾料阳极泥为原料的金、银及其附属产品冶炼生产企业。

Management rules of nonferrous metals balance.Part 5:Gold and silver metallurgy

YS/T 441.4-2014 有色金属平衡管理规范 第4部分:锡选矿冶炼

YS/T 441的本部分规定了锡选矿冶炼金属平衡管理的术语、管理职责、金属平衡计算公式、金属平衡表的编制方法及格式等。本部分适用于锡及其附属产品选矿冶炼生产企业。

Management rules of nonferrous metals balance.Part 4:Tin enrichment and metallurgy

DB63/T 1299-2014 锂离子电池专用电解铜箔

本标准规定了锂离子电池用电解铜箔的术语和定义、产品分类、要求、试验方法、检验规则及包装、标志、贮存及运输。本标准适用于锂离子电池用电解铜箔。

Electrolytic copper foil for lithium ion battery

DB51/T 1782-2014 地质样品中铌、钽的测定 电感耦合等离子体质谱法

Determination of Niobium and Tantalum in Geological Samples by Inductively Coupled Plasma Mass Spectrometry

DB51/T 1781-2014 钒钛磁铁矿中全铁、钛、钒的测定 电感耦合等离子体光谱法

Determination of total iron, titanium and vanadium in vanadium-titanium magnetite by inductively coupled plasma spectrometry

BS ISO 7583:2013 铝及其合金的阳极氧化.术语和定义

Anodizing of aluminium and its alloys. Terms and definitions

YS/T 881-2013 火法冶炼镍基体料

本标准规定了采用红土镍矿为原料火法生产的冶炼镍基体料技术要求、试验方法、检验规则、包装、标志、运输、贮存和质量证明书等。 本标准适用于冶炼不锈钢、冶炼特钢、铸造特殊铸件用镍基体料及镍合金的替代品。

The dominated smelting nickel substrate material

YS/T 876-2013 铝合金挤压在线固溶热处理规范

本标准规定了铝合金挤压在线固溶热处理的术语和定义、设备、工艺、过程控制与质量保证要求、本标准适用于铝合金挤压产品的在线固溶热处理过程、

Standard practice for extrusion solution heat treatment for wrought aluminium alloys