H60 有色金属及其合金产品综合 标准查询与下载

ASTM B899-05 有色金属和合金的相关标准术语

1.1 To promote precise understanding and interpretation of standards, reports, and other technical writings promulgated by Committee B02.1.2 To standardize the terminology used in these documents.1.3 To explain the meanings of technical terms used within these documents for those not conversant with them.

Standard Terminology Relating to Non-ferrous Metals and Alloys

ASTM B275-05 铸造和锻造某些有色金属和合金的标准实施规程汇编

1.1 This practice covers a system originally adopted for designating light metals and alloys, cast and wrought, and later extended to certain heavier, base-metal die-casting alloys. Those designations, which are currently being used in specifications under the jurisdiction of Committees B02 on Nonferrous Metals and Alloys and B07 on Light Metals and Alloys, are listed in Table X2.1.1.1.1 The alloy designations now being used in Committee B07 specifications for aluminum and aluminum-alloy wrought and cast products conform to ANSI H35.1. Alloys formerly codified by this practice and the corresponding ANSI designations are shown in Tables X3.1 and X3.2.1.2 This practice also provides a system for designating magnesium alloys that have been used commercially since 1952, and thus is intended to be the registration source for new magnesium alloys. A record of designations along with the established compositions is given in Table X4.1. 1.3 The equivalent Unified Numbering System (UNS) alloy designations shown in the appendixes are in accordance with Practice E 527.

Standard Practice for Codification of Certain Nonferrous Metals and Alloys, Cast and Wrought

ASTM B677-05 UNS N08925、UNS N08354和UNS N08926无缝管的标准规范

1.1 This specification covers UNS N08925, UNS N08354, and UNS N08926* seamless, cold-worked or hot-finished pipe and tube intended for general corrosive service.1.2 ASTM International has adopted definitions whereby some grades, such as UNS N08904 previously in this specification, were recognized as stainless steels, because those grades have iron as the largest element by mass percent. Such grades are under the oversight of ASTM Committee A01 and its subcommittees. The products of N08904 previously covered in this specification are now covered by Specifications A 269 and A 312.1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

Standard Specification for UNS N08925, UNS N08354, and UNS N08926 Seamless Pipe and Tube

KS B ISO 11562:2004 几何图形制品规范.表面特征:轮廓法.相位校正过滤器的计量特性

이 규격은 표면 단면 곡선의 측정에 대한 위상 보정 필터의 도량형 특성에 대하여 규정한다.

Geometrical Product Specifications(GPS)-Surface texture:Profile method-Metrological characteristics of phase correct filters

ASME BPVC Section 2 Part B-2004 ASME锅炉和压力容器规程.第2节:材料.第B部分:有色金属材料规范

ASME Boiler & Pressure Vessel Code - Section 2: Materials; Part B: Nonferrous Material Specifications

ASTM B275-04 铸造和锻造某些有色金属和合金的标准实施规程

1.1 This practice covers a system originally adopted for designating light metals and alloys, cast and wrought, and later extended to certain heavier, base-metal die-casting alloys. Those designations, which are currently being used in specifications under the jurisdiction of Committees B02 on Nonferrous Metals and Alloys and B07 on Light Metals and Alloys, are listed in Tables X2.1.1.1.1 The alloy designations now being used in Committee B07 specifications for aluminum and aluminum-alloy wrought and cast products conform to ANSI H35.1. Alloys formerly codified by this practice and the corresponding ANSI designations are shown in Tables X3.1 and X3.2.1.2 This practice also provides a system for designating magnesium alloys that have been used commercially since 1952, and thus is intended to be the registration source for new magnesium alloys. A record of designations along with the established compositions is given in Table X4.1. 1.3 The equivalent Unified Numbering System (UNS) alloy designations shown in the appendixes are in accordance with Practice E 527.

Standard Practice for Codification of Certain Nonferrous Metals and Alloys, Cast and Wrought

ASTM B899-04 有色金属和合金的相关标准术语

1.1 To promote precise understanding and interpretation of standards, reports, and other technical writings promulgated by Committee B02.1.2 To standardize the terminology used in these documents.1.3 To explain the meanings of technical terms used within these documents for those not conversant with them.

Standard Terminology Relating to Non-ferrous Metals and Alloys

JIS H 7502:2003 金属超塑材料压缩性能的评价方法

この規格は，微細粒超塑性を示す金属系超塑性材料を，超塑性発現条件の下で圧縮試験を行うことによって，応力一ひずみ線図を求め，その材料の圧縮変形応力を評価する方法について規定する。

Method for evaluation of compressive properties of metallic superplastic materials

JIS H 7504:2003 通过对金属超塑性材料的膨胀试验评价吹制成型法

この規格は，厚さ3mm以下の板状の金属系超塑性材料を，超塑性状態で超塑性パルジ成形法によるブロー成形性試験・評価方法について規定する。

Method for evaluation of blow formability by bulging test on metallic superplastic materials

JIS H 7503:2003 超塑变形金属材料孔穴体积比值的测量方法

この規格は，微細粒超塑性を示す金属系超塑性材料を超塑性発現条件の下で成形した後の空洞率を，質量法による密度変化の測定から求める方法について規定する。

Method for measurement of cavity volume fraction of superplastically deformed metallic materials

ASME SEC II B INTRO-2003 介绍

BPVC SECTION II B Introduction This part is a service book to the other Code Sections providing material specifications for nonferrous materials adequate for safety in the field of pressure equipment. These specifications contain requirements for heat treatment, manufacture, chemical composition, heat and product analyses, mechanical test requirements and mechanical properties, test specimens, and methods of testing. They are designated by SB numbers and are derived from ASTM "B" specifications.

Introduction

ASME SEC II B NMA APP A-2003 附录A.非强制性验收.ASTM版

BPVC Appendix A - Nonmandatory Acceptable ASTM Editions

Appendix A - Nonmandatory Acceptable ASTM Editions

ASME SEC II B A2003-2003 更改摘要

BPVC SECTION II B Summary of Changes

Summary of Changes

ASTM B899-03a 有色金属和合金的相关标准术语

1.1 To promote precise understanding and interpretation of standards, reports, and other technical writings promulgated by Committee B02.1.2 To standardize the terminology used in these documents.1.3 To explain the meanings of technical terms used within these documents for those not conversant with them.

Standard Terminology Relating to Non-ferrous Metals and Alloys

ASTM B483/B483M-03 一般用途铝和铝合金拉制管材标准规范

1.1 This specification covers aluminum and aluminum-alloy drawn tubes in straight lengths and coils for general purpose applications in the alloys (Note 0), and tempers shown in . Coiled tubes are generally available only as round tubes with a wall thickness not exceeding 0.083 in. [2.00 mm] and only in non-heat-treatable alloys.Note 18212;For drawn seamless tubes, see Specifications B 210 and B 210M, for tubes to be used in condensers and heat exchangers, Specifications B 234 and B 234M, and for seamless pipe, Specification B 241/B 241M.Note 28212;Throughout this specification use of the term alloyin the general sense includes aluminum as well as aluminum alloy.1.2 Alloy and temper designations are in accordance with ANSI H35.1 and H35.1M. The equivalent Unified Number System alloy designations are those of preceded by A9, for example A91060 for aluminum 1060 in accordance with Practice E 527.1.3 For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see Annex A2.1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.

Standard Specification for Aluminum and Aluminum-Alloy Drawn Tube and Pipe for General Purpose Applications

ASTM B899-03 有色金属和合金的相关标准术语

1.1 To promote precise understanding and interpretation of standards, reports, and other technical writings promulgated by Committee B02.1.2 To standardize the terminology used in these documents.1.3 To explain the meanings of technical terms used within these documents for those not conversant with them.

Standard Terminology Relating to Non-ferrous Metals and Alloys

ASTM B676-03 UNS N08367焊接管标准规范

1.1 This specification covers UNS N08367* welded tube for general corrosion applications.1.2 This specification covers outside diameter and nominal wall tube.1.2.1 The tube sizes covered by this specification are 1/8 to 5 in. (3.2 to 127 mm) in outside diameter and 0.015 to 0.320 in. (0.38 to 8.13 mm), inclusive, in wall thickness.1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

Standard Specification for UNS N08367 Welded Tube

KS D ISO 197-5:2002 铜和铜合金.术语和定义.第5部分:加工和处理方法

이 규격은 구리 및 구리합금 분야의 가공 및 처리 방법과 관련된 용어 및 정의에 대하여 규

Copper and copper alloys-Terms and definitions-Part 5 : Methods of processing and treatment

KS D ISO 3134-5:2002 轻金属及其合金.术语和定义.第5部分:加工和处理方法

이 규격은 경금속과 경금속합금의 공정 및 처리 방법과 관련된 용어 및 정의에 대하여 규

Light metals and their alloys-Terms and definitions-Part 5 : Methods of processing and treatment

KS D ISO 3134-2:2002 轻金属及其合金.术语和定义.第2部分:未加工品

이 규격은 비전신 경금속과 경금속합금 제품의 용어와 정의에 대해 기술한다.

Light metals and their alloys-Terms and definitions-Part 2 : Unwrought products