J99 其他动力设备 标准查询与下载

ASTM E1602-01 燃烧固体燃料的砖石加热器制作的标准导则

1.1 This guide covers the design and construction of solid fuel burning masonry heaters. It provides dimensions for site constructed masonry heater components and clearances that have been derived by experience and found to be consistent with the safe installation of those masonry heaters.1.2 Values given in SI units are to be regarded as standard. Inch/pound units may be rounded (see IEEE/ASTM SI-10). All dimensions are nominal unless specifically stated otherwise. All clearances listed in this guide are actual dimensions.1.3 This guide applies to the design and construction of masonry heaters built on-site with the components and materials specified herein. It does not apply to the construction/installation requirements for component systems that have been safety tested and listed. The requirements for listed masonry heater systems are specified in the manufacturer''s installation instructions.1.4 The design and construction of solid fuel burning masonry heaters shall comply with applicable building codes.

Standard Guide for Construction of Solid Fuel Burning Masonry Heaters

SY/T 0097-2000 稠油油田采出水用于蒸汽发生器给水处理设计规范

本规范适用于陆上稠油油田采出水用于蒸汽发生器(出口蒸汽干度小于或等于80%)给水处理的新建、扩建和改建工程设计。

Design specification for heavy oil field produced water treatment as steam generator feedwater

KS B 6877-2000 蜗轮减速器性能试验及测试方法

이 규격은 동력 전달용으로 사용되는 감속 장치의 일종으로, 1단 웜 감속인 경우 감속비가

Test code for performance of worm reducers

BS EN 12514-2:2000 油燃烧器供油系统的安装.安全性要求和试验.部件、阀门、管道、过滤器、油空气分离器、油量计

This standard applies to parts, valves, pipes, filters, oil de-aerators and meters of oil supply installations for automatic supply of one or more oil burners or oil consuming units with light fuel oil (maximum viscosity of 10 mm/s at a temperature of 20 ℃) from one or more central storage tanks under static or dynamic pressure. This standard covers all the above mentioned components between the connection to one or more tanks and the connection to oil burners or oil consuming units, including the direct series-connected shut-off devices. EN 12514-1 covers technical safety requirements and tests for parts, oil feed pumps, control and safety devices and oil supply tanks. This standard specifies the safety requirements and corresponding tests for all parts, valves, pipes, filters, oil de-aerators and meters within an oil supply installation.

Installations for oil supply systems for oil burners - Safety requirements and tests - Parts, valves, pipes, filters, oil de-aerators, meters

BS EN 12514-1:2000 油燃烧器供油系统的安装.安全性要求和试验.零部件、供油泵、控制和安全装置、供油罐

Installations for oil supply systems for oil burners - Safety requirements and tests - Parts, oil feed pumps, control and safety devices, supply tanks

DIN EN 12514-2:2000 油燃烧器供油系统的安装.第1部分:安全要求和试验.部件,阀门管道,过滤器,油气分离器,油量计

This document applies to parts, valves, pipes, filtres Oil de-aerators and meters of oil supply installations for automatic supply of one or more oil burners or oil consuming units with light fuel oil from one or more central oil storage tanks under static or dynamic pressure. It specifies the safety requirements and corresponding tests for all parts, valves, pipes, filtres, oil de-aerators and meters within an oil supply installation.#,,#

Installations for oil supply systems for oil burners - Part 2: Safety requirements and tests; parts, valves pipes, filters, oil de-aerators, meters; German version EN 12514-2:2000

DIN EN 12514-1:2000 油燃烧器供油系统的安装.第1部分:部件、供油泵、控制和安全装置及供油罐的安全要求和试验

Installations for oil supply systems for oil burners - Part 1: Safety requirements and tests; parts, oil feed pumps, control and safety devices, supply tanks; German version EN 12514-1:2000

KS B 6855-1999 割草机软性轴组件

이 규격은 잔디 깎기용, 풀베기용 및 산림용으로 사용되고 있는, 휴대용 예초기의 동력 전달

Flexible shaft assembly of brush cutter

BS EN 267:1999 强制通风油燃烧器.定义、要求、试验和标记

This European Standard specifies the test requirements and methods for laboratory testing of forced draught oil burners supplied with a fuel having a viscosity at the burner inlet of 1,6 mm/s (cSt) up to 6 mm/s (cSt) at 20 ℃. This standard also applies to the oil function of dual fuel burners designed to operate on liquid and gaseous fuels in which case the requirements of EN 676 will also apply in respect of the gaseous fuel function. This standard does not apply to burners intended for use in industrial processes although some aspects of the standard may be relevant.

Forced draught oil burners - Definitions, requirements, testing, marking

BS 1113:1999 水管式蒸汽发生装置(包括过热器、再热器和钢管式节热器)的设计与生产规范

1 This British Standard specifies requirements for the design and the manufacture, including materials and design stresses, workmanship, inspection, testing, documentation and marking, valves, gauges and fittings of: a) water-tube steam generating plant subject to internal pressure; and b) parts of steam and water heating plant used in association with steam generating plant. 2 In addition to the definitive requirements, this standard also requires the items detailed in 1.5 to be documented. For compliance with this standard, both the definitive requirements and the documented items have to be satisfied. 3 This British Standard applies to the following types of plant. a) Water-tube boilers including their integral steel tube economizers and superheaters and all other parts connected to the boiler without the interposition of a shut-off valve with the exception of valves and fittings specified in section 7. Water-tube boilers are divided, for the purposes of this British Standard, into the following three classes. 1) Natural circulation boilers, in which the circulation of the water through the tubes is a result of the thermo-syphonic head produced by heating. 2) Forced, assisted or controlled circulation boilers, in which a pump is used either entirely or partly to promote circulation of the water through the tubes. 3) Once-through boilers, in which the feed pump is used to force the flow of water and steam through the tubes. b) Steam reheaters (either integral with the boiler unit or independently fired) receiving steam which has passed through part of a turbine or other prime mover. c) Independently fired steam superheaters. d) Integral superheaters separated by a shut-off valve from the evaporative circuits. e) Steel tube economizers (either integral with the boiler or independently fired) separated by a shut-off valve from the boiler. NOTE. For convenience, the term 'boiler' used throughout this standard includes the types of plant described in a) to e). 4 This standard applies to the pressure parts of boilers and superheaters (as described in 1.1.3a) and d)) containing water and steam up to and including the valves separating these water and steam spaces from the steam pipes to other equipment, water supply pipes, drain pipes and the surrounding atmosphere (safety valves and vents). In the case of reheaters (see 1.1.3b), this standard applies to pressure parts from the piping connection(s) at the inlet header to the piping connection(s) at the outlet header except that where a device is provided in reheat piping to blank off the reheater for hydraulic testing, this standard applies up to and including this device. In the case of independently fired superheaters (see 1.1.3c), and economizers (see 1.1.3e), the standard applies to the pressure parts containing steam and water respectively between the inlet and exit valves, including the respective valves and connections to drain pipes and to the atmosphere. 5 Section 4 of this standard (manufacture and workmanship) includes requirements applicable to the normal function of the boilermaker. Requirements for the quality of workmanship of plates, tubes, forgings and castings in the condition in which they are normally supplied to the boilermaker are included in the standards in the series specifying such materials. 6 This standard does not apply to brickwork or other settings or supports, or to insulation, or to air preheaters, mechanical stokers, fuel burning or ash disposal equipment, forced or induced draught equipment or their accessories. These items are matters for mutual agreement between the purchaser and the manufacturer. NOTE. Where such items are required or contemplated, it is recommended that all particulars which could affect the boiler(s) should be disclosed by the purchaser to the manufacturer at the time of the enquiry. 7 This standard applies only to boilers manufactured under the survey of a competent engineering Inspecting Authority or organiza

Specification for design and manufacture of water-tube steam generating plant (including superheaters, reheaters and steel tube economizers)

JB/T 8963-1999 蒸汽发生器安全要求

本标准规定了蒸汽发生器的安全要求和试验方法。 本标准适用于工业洗涤等行业使用的电加热式发生器。

Safety requirements of steam generators

JB/T 8959-1999 蒸汽发生器

本标准规定了蒸汽发生器（以下简称发生器）的产品分类、基本参数、技术要求、试验方法、检验规则、运输与贮存。 本标准适用于工业洗涤等行业使用的电加热式发生器。

Steam generators

KS B 6840-1998 建筑机械人类工效学.操控室空间的优化设计

이 규격은 건설 기계의 운전실 내에서 운전자의 안전, 조작의 편의성 및 안락성을 위한 인간

Human physical dimensions of operators and design of the optimum cabin space for construction machinery

BS EN 1:1998 带有蒸气燃烧器的燃油炉

This standard applies to flued oil stoves with one or more vaporizing burners (hereafter referred to as "stoves") as used for individual heating in the domestic field and having either a draught regulator or a combustion air limiter as defined in 3.13 and a nominal heating capacity of not more than 15 kW. It is not applicable for built-in equipment. According to the type of fuels used in the country of destination, the stoves are supplied for use with either. —fuel oil with a maximum kinematic viscosity of 6,0mm/s at 20℃; —or kerosene with a flash point of not less than 40 ℃. These liquid fuels are hereafter called oil.

Flued oil stoves with vaporizing burners

ASME PTC 4-1998 燃烧式蒸汽发生器

This Code provides rules and instructions for conducting performance tests of fuel fired steam generators. These include coal, oil, and gas fired steam generators as well as steam generators fired by other hydrocarbon fuels. The scope also includes steam generators with integral fuel-sulfur capture utilizing chemical sorbents. Steam generators which are not fired by coal, oil, or gas may be tested using the concepts of this Code, but it should be noted that the uncertainty caused by variability of the fuel may be difficult to determine and is likely to be greater than the uncertainties in sampling and analysis of coal, oil, or gas. For example, gas turbine heat recovery and other heat recovery steam generators designed to operate with supplemental firing should be tested in accordance with PTC 4.4. Testing of auxiliary equipment is not addressed in this Code, but are covered PTC 4.2, PTC 4.3 and PTC 11. This Code does not prescribe procedures for testing to determine chemical and physical properties of fuels. This Code specifically addresses equipment used for the generation of steam; however, the basic principles presented are also applicable to other working fluids. Certain types and sizes of equipment used for the recovery of heat released by combustion are not addressed in any specific Performance Test Code. This Code can be used as a general guide in developing performance tests for such equipment; however, such specifically developed performance tests shall not be considered ASME Code tests. This Code provides general procedures for conducting combustible fuel fired steam generator performance tests; however, it cannot possibly provide detailed procedures applicable to every steam generator design variation. Design variations considered in developing this Code include subcritical and supercritical once-through steam generators and oil, gas, stoker, cyclone, pulverized, and fluidized bed firing. For each performance test, a competent engineer must study the actual steam generator and its relation to the remainder of the steam cycle, and develop test procedures which are consistent with this Code. A test report shall be prepared. Many references, which are listed in this Code provide useful supplemental information in planning for a performance test in accordance with this Code.

Fired steam generators

UL 331-1997 可燃液体和无水液氨用滤净器

Strainers for flammable fluids and anhydrous ammonia

BS EN 676:1997 气体燃料用自动强制送风燃烧器

Automatic forced draught burners for gaseous fuels

NF E32-020-2:1996 工业加热设备.固定人工操作或无人操作的蒸汽或过热蒸汽发生器的安全性.第2部分:电力设备的特定要求

Industrial heating equipements. Safety of steam or superheated steam generators, permanently manned or not. Part 2 : specific requirements for electric installations.

DIN V 4753-8:1996 饮用水和服务用水加热器和加热设备.第8部分:额定容量不超过1000 l水加热器的隔热性.要求和试验

The document specifies minimum requirements for heat the insulation of water heaters with a nominal capacity up to 1000 l, which are manufactures in series as well as the limit values for the heat loss of heat insulated vessels.#,,#

Water heaters and water heating installations for drinking water and for service water - Part 8: Thermal insulation for water heaters with nominal capacity up to 1000 l - requirements and testing

JIS S 3025:1996 燃烧装置的燃料供给管和排气管

この規格は，石油又はがスを燃料とする強制給排気形又は強制給排気式の燃焼機器に用いる給排気筒について規定する。

Supply and exhaust pipes for burning appliances