K33 控制继电器 标准查询与下载

BS EN 60255-26:2009 继电器.量度继电器和保护装置的电磁兼容性要求

This part of IEC 60255 is applicable to measuring relays and protection equipment for power system protection, including the control, monitoring and process interface equipment used with those systems. This standard specifies the essential requirements for electromagnetic compatibility for measuring relays and protection equipment intended to be used at industrial locations. Measuring relays and protection equipment used in substations and power plants may require higher immunity test levels. For equipment not incorporating electronic circuits, for example electromechanical relays, tests according to this standard are not required. The requirements specified in this standard are applicable to measuring relays and protection equipment in a new condition and all tests specified are type tests only. 1.1 Emission The object of this standard is to specify limits and test methods, for measuring relays and protection equipment in relation to electromagnetic emissions which may cause interference in other equipment. These emission limits represent electromagnetic compatibility essential requirements and have been selected to ensure that the disturbances generated by measuring relays and protection equipment, operated normally in substations and power plants, do not exceed a level which could prevent other equipment from operating as intended. Test requirements are specified for the enclosure and power supply ports. 1.2 Immunity The object of this standard is to specify the essential immunity test requirements for measuring relays and protection equipment in relation to continuous and transient, conducted and radiated disturbances, including electrostatic discharges. These test requirements represent the essential electromagnetic compatibility immunity requirements selected to ensure an adequate level of immunity for measuring relays and protection equipment. NOTE 1 Safety considerations are not covered in this standard. NOTE 2 In special cases, situations will arise where the levels of disturbance may exceed the levels specified in this standard, for example where a hand-held transmitter is used in close proximity to measuring relays and protection equipment. In these instances, special precautions may have to be employed.

Measuring relays and protection equipment - Electromagnetic compatibility requirements

NF C45-200-26:2009 测量继电器和保护设备.第26部分:电磁兼容性要求

Measuring relays and protection equipment - Part 26 : electromagnetic compatibility requirements.

DIN EN 61810-1:2009 机电式单元继电器.第1部分:一般要求

Electromechanical elementary relays - Part 1: General requirements (IEC 61810-1:2008); German version EN 61810-1:2008

DIN EN 60255-22-4:2009 继电器和保护设备的测量.第22-4部分:电干扰试验.电气快速瞬变/脉冲抗扰性试验

Measuring relays and protection equipment - Part 22-4: Electrical disturbance tests - Electrical fast transient/burst immunity test (IEC 60255-22-4:2008); German version EN 60255-22-4:2008

DIN EN 60255-22-2:2009 测量继电器和保护设备.第22-2部分:电气干扰试验.静电放电试验

Measuring relays and protection equipment - Part 22-2: Electrical disturbance tests - Electrostatic discharge tests (IEC 60255-22-2:2008); German version EN 60255-22-2:2008

ANSI/IEEE C37.234:2009 电网母线使用的继电保护器指南

Concepts of power bus protection are discussed in this guide. Consideration is given to availability and location of breakers, current transformers and disconnectors as well as bus switching scenarios, and their impact on the selection and application of bus protection.

Guide for Protective Relay Applications to Power System Buses

NF C45-200-22-3:2008 测量继电器和保护设备.第22-3部分:电气干扰试验.辐射电磁场抗扰度

Measuring relays and protection equipment - Part 22-3 : electrical disturbance tests - Radiated electromagnetic field immunity.

BS EN 60255-22-3:2008 量度继电器和保护装置.第22-3部分:电干扰试验.辐射电磁场抗扰性

This part of IEC 60255 is based on IEC 61000-4-3, referring to that publication where applicable, and specifies the general requirements for radiated electromagnetic field immunity tests for measuring relays and protection equipment for power system protection, including the control, monitoring and process interface equipment used with those systems. The objective of the tests is to confirm that the equipment under test (EUT) will operate correctly when energised and subjected to an electromagnetic field from a radiation source operating within the frequency range 80 MHz to 2,7 GHz. NOTE 1 The product standard IEC 60255-22-6 (based on IEC 61000-4-6) establishes the immunity of measuring relays and protection equipment over the frequency range of 0,15 MHz to 80 MHz. NOTE 2 The test methods defined in this standard are structured for the primary objective of establishing adequate repeatability of results at various test facilities for qualitative analysis of effects. The test methods using a portable transmitter1 are not taken into consideration here because the EMC directive now specifies a sweep test, calibrated field strengths must be used and the portable transmitter test is not generally reproducible. The requirements specified in this standard are applicable to measuring relays and protection equipment in a new condition, and all tests specified are type tests only.

Measuring relays and protection equipment - Part 22-3:Electrical disturbance tests - Radiated electromagnetic field immunity

IEC 60255-11:2008 测量继电器和保护设备 第11部分 自备供电设备端口上电压降、短时中断、变化和波动

This part of the IEC 60255 series specifies the general requirements for a.c. and d.c. power supplies, for measuring relays and protection equipment for power system protection, including the control, monitoring and process interface equipment used with those systems. This part is based on: ~ IEC 61000-4-11 for a.c. voltage dips, short interruptions and variations; ~ IEC 61000-4-17 for voltage ripple; ~ IEC 61000-4-29 for d.c. voltage dips, short interruptions and variations. The objective of the tests is to confirm that the equipment under test will operate correctly when energised and subjected to dips, interruptions and alternating components (ripple). The requirements specified in this standard are applicable to measuring relays and protection equipment in a new condition and all tests specified are type tests only. The object of this standard is to state: ~ definitions of terms used; ~ test severity levels; ~ test equipment; ~ test set-up; ~ test procedure; ~ criteria for acceptance; ~ test report.

Measuring relays and protection equipment - Part 11: Voltage dips, short interruptions, variations and ripple on auxiliary power supply port

BS EN 61810-1:2008 机电元件继电器.通用要求

This part of IEC 61810 applies to electromechanical elementary relays (non-specified time allor- nothing relays) for incorporation into equipment. It defines the basic functional requirements and safety-related aspects for applications in all areas of electrical engineering or electronics, such as: • general industrial equipment, • electrical facilities, • electrical machines, • electrical appliances for household and similar use, • information technology and business equipment, • building automation equipment, • automation equipment, • electrical installation equipment, • medical equipment, • control equipment, • telecommunications, • vehicles, • transportation (e.g. railways). Compliance with the requirements of this standard is verified by the type tests indicated. In case the application of a relay determines additional requirements exceeding those specified in this standard, the relay should be assessed in line with this application in accordance with the relevant IEC standard(s) (e.g. IEC 60730-1, IEC 60335-1, IEC 60950-1).

Electromechanical elementary relays. General requirements

BS EN 60255-22-2:2008 测量继电器和保护设备.电气干扰试验.静电放射试验

Measuring relays and protection equipment. Electrical disturbance tests. Electrostatic discharge tests

IEC PAS 61810-2-1:2008 机电的基本继电器.第2-1部分:可靠度.B₁₀数值的验证程序

This PAS specifies reliability test procedures for electromechanical elementary relays when enhanced requirements for the verification of reliability apply. Particular provisions are given for relays incorporated in safety-related control systems of machinery in accordance with IEC 62061 and ISO 13849-1. For such relays Ble values for dangerous failures (B values) are derived from the tests specified in this PAS. This specification is only intended to be used in conjunction with IEC 61810-2.

Electromechanical elementary relays - Part 2-1: Reliability - Procedure for the verification of B₁₀ values

BS EN 60255-22-1:2008 测量继电器和保护设备.第22-1部分:电气干扰试验.1MHz脉冲抗扰性试验

This part of IEC 60255 is based on IEC 61000-4-18, referring to that publication where applicable, and specifies the general requirements for 1 MHz oscillatory wave immunity tests for measuring relays and protection equipment for power system protection, including the control, monitoring and process interface equipment used with the relays and protection equipment. The objective of the tests is to confirm that the equipment under test will operate correctly when energised and subjected to repetitive damped oscillatory waves such as those originating from closing or opening circuit breakers or disconnectors in high voltage substations or power plants. The requirements specified in this standard are applicable to measuring relays and protection equipment in a new condition and all tests specified are type tests only.

Measuring relays and protection equipment - Part 22-1: Electrical disturbance tests - 1 MHz burst immunity tests

BS EN 62314:2007 固态继电器

Solid-state relays

IEC 60255-22-1:2007 测量继电器和保护设备.第22-1部分:电气干扰试验.1MHz猝发抗扰性试验

This part of IEC 60255 is based on IEC 61000-4-18, referring to that publication where applicable, and specifies the general requirements for 1 MHz oscillatory wave immunity tests for measuring relays and protection equipment for power system protection, including the control, monitoring and process interface equipment used with the relays and protection equipment. The objective of the tests is to confirm that the equipment under test will operate correctly when energised and subjected to repetitive damped oscillatory waves such as those originating from closing or opening circuit breakers or disconnectors in high voltage substations or power plants. The requirements specified in this standard are applicable to measuring relays and protection equipment in a new condition and all tests specified are type tests only.

Measuring relays and protection equipment - Part 22-1: Electrical disturbance tests - 1 MHz burst immunity test

ANSI/IEEE C37.116:2007 传输线串联电容器组用保护继电器的指南

Application of protective relays on transmission-line series capacitor banks is covered. Purpose is to provide the reader with ample discussion of the protection and control issues related to series capacitor bank installations.

Guide for Protective Relay Application to Transmission-Line Series Capacitor Banks

ANSI/IEEE C37.117:2007 不规则频率荷载降低和复位用保护继电器的应用指南

Compiles information on the application of underfrequency load shedding and restoration to ac power systems. Describes various system conditions that may require the use of underfrequency load shedding, and the application of protective relays to various methods of performing underfrequency load shedding

Guide for the Application of Protective Relays Used for Abnormal Frequency Load Shedding and Restoration

IEC 60255-22-3:2007 测量继电器和保护设备.第22-3部分:电气骚扰试验.辐射电磁场抗扰性

This part of IEC 60255 is based on IEC 61000-4-3, referring to that publication where applicable, and specifies the general requirements for radiated electromagnetic field immunity tests for measuring relays and protection equipment for power system protection, including the control, monitoring and process interface equipment used with those systems.

Measuring relays and protection equipment - Part 22-3: Electrical disturbance tests - Radiated electromagnetic field immunity

DIN EN 62314:2007 固态继电器

Solid-state relays (IEC 62314:2006); German version EN 62314:2006

JB/T 10711-2007 塑料外壳式断路器可靠性试验方法

本标准规定了塑料外壳式断路器（简称塑壳断路器），进行可靠性验证试验的一般要求。 本标准适用于符合GB 14048.2-2001、交流5OHz（6OHz）、额定电压不超过1000v、额定电流250A及以下的塑壳断路器。除验证试验方案及试验程序外，本标准也适用于产品的可靠性测定试验。 额定电流250A以上的塑壳断路器的可靠性试验可参照本标准进行。

Reliability test method of moulded case circuit-breakers