K33 控制继电器 标准查询与下载

IEC 60255-27/COR1:2007 量度继电器和保护设备.第27部分:产品安全性要求.勘误表1

This standard is Measuring relays and protection equipment - Part 27: Product safety requirements; Corrigendum 1.

Measuring relays and protection equipment - Part 27: Product safety requirements; Corrigendum 1

DIN EN 61810-7:2007 机电元件继电器.第7部分:试验和测量程序

Electromechanical elementary relays - Part 7: Test and measurement procedures (IEC 61810-7:2006); German version EN 61810-7:2006

BS EN 60255-27:2005 测量继电器和保护设备.第27部分:产品安全要求

This International Standard describes the product safety requirements for measuring relays and protection equipment having a rated a.c. voltage up to 1 000 V with a rated frequency up to 65 Hz, or a rated d.c. voltage up to 1 500 V. Above these limits, IEC 60664-1 should be used for the determination of clearance, creepage distance and withstand test voltage. This standard details essential safety requirements to minimize the risk of fire and hazards caused by electric shock or injury to the user. This standard does not cover the safety requirements of installations. It does cover all the ways in which the equipment may be mounted and used in cubicles, racks and panels, and also re-testing. This standard also applies to auxiliary devices such as shunts, series resistors, transformers, etc., solely used and tested together with measuring relays and protection equipment. Ancillary equipment used in conjunction with measuring relays and protection equipment may need to comply with additional safety requirements. This standard is intended to describe only product safety requirements; therefore, functional performance of the equipment is not covered. Functional safety requirements, including EMC functional safety, are not covered by this standard. Functional safety risk analysis is not within the scope of this product safety standard. This standard does not specify individual equipments or implementations of circuits and components. The object of this standard is to have a comprehensive standard that covers all aspects of product safety and the related type and routine tests, for measuring relays and protection equipment.

Measuring relays and protection equipment - Part 27: Product safety requirements

DIN EN 60255-27:2006 测量继电器和保护设备.第27部分:产品安全要求(IEC 60255-27-2005)

Measuring relays and protection equipment - Part 27: Product safety requirements (IEC 60255-27:2005); German version EN 60255-27:2005

BS EN 61810-7:2006 机电式单元继电器.试验和测量程序

This part of IEC 61810 states the test and measurement procedures for electromechanical elementary relays. It covers basic considerations which are, in general, common to all types of electromechanical elementary relays. Supplementary requirements may be necessitated by specific designs or application. The test and measurement procedures of this standard are described as individual provisions covering a specific requirement. When combining them in a test programme, care must be taken (for example by suitable grouping of tested relays) to ensure that preceding tests do not devalue subsequent ones. Where in this standard the term “specified” is used, this means a prescription in the appropriate documentation for the relay, for example manufacturer’s data sheet, test specification, customer detail specification. For application within the IECQ system such prescriptions are contained in the detail specification as defined in Clause A.7 of QC 001001. NOTE 1 To improve the readability of this standard, the term “relay” is generally used in place of “electromechanical elementary relay”. NOTE 2 Requirements and tests related to the type testing of electromechanical elementary relays are contained in IEC 61810-1. For that purpose, the generally described test and measurement procedures of this standard have been prescribed in a more restricted and stringent form in IEC 61810-1. NOTE 3 Standards covering relays subjected to quality assessment in accordance with IECQ are compiled in the IEC 61811 series of publications.

Electromechanical elementary relays - Test and measurement procedures

JB/T 10549-2006 SF₆气体密度继电器和密度表.通用技术条件

本标准规定了SF气体密度继电器和密度表的分类、技术要求、检验方法、检验规则、标志、标签、使用说明书、包装、运输和贮存等。 本标准适用于SF气体密度继电器和密度表（以下简称“产品”），适用于产品装配的实际位置的温度与被测值SF气体的实际温度一致的情况，作为设计、制造、检验、使用该产品的依据。对于被测值的SF气体有升温(例如：运行中的SF断路器、CIS、电流互感器、电压互感器等高电压电气设备)的情况，测量数据仅作参考。

Common specification for SF gas density relay and density meter

IEC 62314:2006 固态继电器

This International Standard applies to particular all-or-nothing electrical relays denominated solid-state relays intended for performing electrical operations by single step function changes to the state of electric circuits between the OFF-state and the ON-state and vice versa. It is applicable to solid-state relays with rated voltages up to 750 V and with a.c. output current up to 160 A. NOTE Requirements for solid-state relays with d.c. output circuits are under consideration. This standard deals with solid-state relays which are intended for incorporation in other products or equipment. As such, solid state relays are considered to be components and this standard defines the basic safety-related and functional requirements for solid-state relays as stand-alone components. Such solid-state relays are incorporated in products or equipment which themselves have to comply with the relevant product and/or application standard(s) to meet their intended application. The following are examples of such applications: – general industrial equipment; – electrical facilities; – electrical machines; – electrical appliances; – office communications; – building automation and environmental control; – automation and process control; – electrical installation engineering; – medical engineering; – telecommunications; – vehicle engineering; – transportation engineering; – lighting control. Solid state relays are components (not stand alone devices) and as such do not perform a direct function. Therefore, no EMC requirements are included in this standard. NOTE This is in line with the European EMC Directive. Where the application of a solid-state relay determines additional requirements such as EMC and overcurrent protection, the solid-state relay shall be assessed in accordance with the relevant IEC standard(s). Solid-state switching devices with monolithic structures fall within the scope of IEC subcommittee 47E and are not covered in this standard. Semiconductor controllers and contactors fall within the scope of the IEC 60947 series of standards – Low-voltage switchgear and controlgear – developed by IEC subcommittee 17B and are not covered in this standard. Compliance with the requirements of this standard is verified by the type tests indicated.

Solid-state relays

BS EN 60255-22-1:2005 继电器.第22-1部分:测量继电器和保护设备的电干扰试验.1MHZ突发抗扰性试验

Electrical relays - Part 22-1: Electrical disturbance tests for measuring relays and protection equipment-1 MHz burst immunity tests

KS C IEC 60255-22-1:2005 测量继电器和保护设备.第22.1部分:电气干扰试验.1MHz猝发抗扰性试验

이 규격의 목적은 측정 릴레이 및 보호 장비에 대한 전기적 장해 시험을 위한 일반적인 요

Electrical disturbance tests for measuring relays and protection equipment－Part 1：1 MHz burst disturbance tests

BS EN 61810-2:2005 机电式初等继电器.可靠度

This part of IEC 61810 covers test conditions and provisions for the evaluation of endurance tests using appropriate statistical methods to obtain reliability characteristics for relays. This standard applies to electromechanical elementary relays considered as non-repaired items (i.e. items which are not repaired after failure), whenever a random sample of items is subjected to a test of cycles to failure (CTF). The lifetime of a relay is usually expressed in number of cycles. Therefore, whenever the terms “time” or “duration” are used in the basic standard IEC 61649, this term is to be understood to mean “cycles”. However, with a given frequency of operation, the number of cycles can be transformed into respective times (e.g. TTF, times to failure). The failure criteria and the resulting characteristics of elementary relays describing their reliability in normal use are specified in this standard. A relay failure occurs when the specified failure criteria are met. As the failure rate for elementary relays cannot be considered as constant, particularly due to wear-out mechanisms, the times to failure of tested items typically show a Weibull distribution. This standard provides numerical methods to calculate approximate values for the two-parameter Weibull distribution, as well as lower confidence limits.

Electromechanical elementary relays - Reliability

IEEE Std C37.92-2005 电子电压和电流转换器的保护继电器的模拟输入

Defines the interface between voltage or current tranducer systems or sensing systems with analog electronic outputs, and suitably designed protective relays or other substation measuring equipment.

Analog inputs to protective relays from electronic voltage and current transducers

JB/T 5806-2005 船用双金属片式热过载继电器

本标准规定了船用双金属片式热过载继电器(以下简称热继电器)的工作条件、技术要求、试验方法、检验规则、标志、包装、运输和贮存等内容。 本标准适用于电压为660V及以下的交流5OHz或6OHz、电流不大于630A、用于三相交流电动机过载和断相保护的热继电器。

Bimetallic thermal overload relay in ships

KS C IEC 61811-10:2004 经质量评定的机电式有或无继电器.第10部分:分规范.工业用继电器

이 규격은 산업용으로 품질 평가된 전자-기계적 기본(비규정 시간의 올 오어 나싱) 계전기에

Electromechanical elementary relays of assessed quality－Part 10：Sectional specification－Relays for industrial application

KS C IEC 61811-1:2004 已评定质量的机电非特定的"有"或"无"继电器.第1部分:通用规范

이 규격은 일반 시방으로 품질 평가된 전자-기계적 비규정 시간의 올 오어 나싱(all-or

Electromechanical non-specified time all-or-nothing relays of assessed quality－Part 1：Generic specification

KS C IEC 61811-11:2004 经质量评定的机电式有或无继电器.第11部分:空白详细规范.工业用继电器

이 규격은 산업용 품질 평가된 전자 기계적 기본(비규정 시간의 올 오어 나싱) 계전기에 적

Electromechanical elementary relays of assessed quality－Part 11：Blank detail specification－Relays for industrial application

IEEE Std C37.90.1/COR-2004 与电力设备相关的继电器和继电器系统用耐电涌性能(SWC)试验

Correction to: IEEE Standard for Surge Withstand Capability (SWC) Tests for Relays and Relay Systems Associated with Electric Power Apparatus

Surge Withstand Capability (SWC) tests for relays and relay systems associated with electric power apparatus

IEEE Std C37.90.1/COR 2-2004 修改:与电力仪器相关的继电器和继电器系统用耐电涌性能(SWC)试验用IEEE标准

Correction to: IEEE Standard for Surge Withstand Capability (SWC) Tests for Relays and Relay Systems Associated with Electric Power Apparatus

Correction to: IEEE Standard for Surge Withstand Capability (SWC) Tests for Relays and Relay Systems Associated with Electric Power Apparatus

BS EN 61810-1:2004 机电式初等继电器.一般和安全要求

This part of IEC 61810 applies to electromechanical elementary relays (non-specified time all-or-nothing relays) for incorporation. It defines the basic safety-related and functional requirements for applications in all areas of electrical engineering or electronics, such as: · general industrial equipment, · electrical facilities, · electrical machines, · electrical appliances for household and similar use, · information technology and business equipment, · building automation equipment, · automation equipment, · electrical installation equipment, · medical equipment, · control equipment, · telecommunications, · vehicles, · transportation, · etc. Compliance with the requirements of this standard is verified by the type tests indicated. In case the application of a relay determines additional requirements exceeding those specified in this standard, the relay should be assessed in line with this application in accordance with the relevant IEC standard(s) (for example IEC 60730-1, IEC 60335-1, IEC 60950-1).

Electromechanical elementary relays - General and safety requirements

BS EN 61811-10:2003 机电"有"或"无"继电器.分规范.工业用继电器

This part of IEC 61811 is a sectional specification applicable to electromechanical elementary (non-specified time all-or-nothing) relays of assessed quality for industrial application. NOTE Electromechanical all-or-nothing telecom relays of assessed quality are covered by IEC 61811-50. It is based on the basic relay standard IEC 61810-1 as well as on the generic specification IEC 61811-1 and selects from IEC 61810-7 the appropriate test and measurement procedures to be used in detail specifications derived from this specification. Moreover it contains a basic test schedule to be used in the preparation of such specifications. Detailed test schedules are given in the blank detail specifications supplementary to this sectional specification. For the purpose of this standard, only fundamental tests have been compiled. Depending on the field of application, further tests should be selected as appropriate, preferably in accordance with the test and measurement procedures of IEC 61810-7.

Electromechanical all-or-nothing relays - Sectional specification - Relays for industrial application

IEEE Std C37.90.1/COR-2003 与电力装置相关的继电器和中继系统的耐电涌性能(SWC)试验.更正

Surge Withstand Capability (SWC) tests for relays and relay systems associated with electric power apparatus; Correction