共找到 61 条与 相关的标准,共 5 页
Fire hazard testing - Part 9-1: Surface spread of flame - General guidance
Measurement equipment generating and/or using radio frequency energy for industrial, scientific, medical, domestic or similar purposes within the frequency range 9 kHz to 400 GHz.
Limits and methods of measurement of radio disturbance characteristics of industrial, scientific and medical (ISM) radio-frequency equipment
This part of IEC 60352 is applicable to insulation piercing connections made with stranded wires and tinsel-wire, flat conductors and flat flexible circuitries for use in telecommunication equipment and in electronic devices employing similar techniques. Information on materials and data from industrial experience is included in addition to the test procedures to provide electrically stable connections under prescribed environmental conditions. The object of this standard is to - determine the suitability of insulation piercing connections under specified mechanical, electrical, and atmospheric conditions; - provide a means of comparing test results when the tools used to make the connections are of different designs or manufacture. There are different designs and materials for insulation piercing terminations in use. For this reason only fundamental parameters of the termination, the performance requirements of the conductor and the complete connection are specified in this standard.
Solderless connections - Part 6: Insulation piercing connections - General requirements, test methods and practical guidance
This part of IEC 60352 is applicable to wrapped connections made with single solid round wires with nominal diameters of 0,16 mm minimum and appropriately designed posts for use in telecommunications equipment and in electronic devices employing similar techniques. Information on materials and data from industrial experience are included in addition to the test procedures to provide electrically stable connections under prescribed environmental conditions. The object of this standard is to determine the suitability of wrapped connections under specified mechanical, electrical and atmospheric conditions, and to provide a means of comparing test results when the tools used to make the connections are of different design or manufacture.
Solderless connections - Part 1: Wrapped connections - General requirements, test methods and practical guidance
Amends clause 11, replaces the existing list of normative references and the existing contents of section four.
Solderless connections - Part 2: Solderless crimped connections - General requirements, test methods and practical guidance; Amendment 1
Applicable to non-accessible ID connections for which the tests and measurements of section 3 are suitable and wich are made with: appropriately designed ID terminations; wires having solid round conductors of 0,25 mm to 3,6 mm nominal diameter; wires ha
Solderless connections - Part 4: Solderless non-accessible insulation displacement connections - General requirements, test methods and practical guidance
Glossary of Electrotechnical, power, telecommunication, electronics, lighting and colour terms Committees responsible National foreword Guide to the glossary Glossary 722-01 General terms 722-02 Telephone set components 722-03 Telephone set feeding and signalling 722-04 Telephone set types 722-05 Telephone set accessories 722-06 Telephone networks 722-07 Telephone exchanges 722-08 Private telephone system 722-09 Description of private telephone systems (under consideration) 722-10 Telephone calls description 722-11 Telephone services (under consideration) 722-12 Local line networks 722-13 Telephone station usage 722-14 Private installation operation (under consideration) 722-15 Transmission performance 722-16 Measuring apparatus 722-17 Telephonometry Index
Glossary of electrotechnical, power, telecommunication, electronics, lighting and colour terms. Terms particular to telecommunications and electronics. Telephony
Applies to ID connections accessible for tests and measurements specified and made with appropriately designed ID terminations, wires having solid round conductors of 0,25 mm to 3,6 mm nominal diameter, and wires having stranded conductors of 0,5 mm
Solderless connections; part 3: solderless accessible insulation displacement connections; general requirements, test methods and practical guidance
Fire hazard testing; part 2: test method; section 2: needle-flame test
Electrotechnical vocabulary. Chapter 714 : switching and signalling (in tlecommunication).
Gives terms and definitions in English, French, Russian and Spanish as well as indexes in Dutch, English, French, German, Italian, Polish, Russian, Spanish, and Swedish.
International electrotechnical vocabulary; chapter 191: dependability and quality of service
Applies to solderless crimped connections made with stranded wires and appropriately designed crimp barrels for use in telecommunication equipment and in electronic devices employing similar techniques. Information on materials and data from industrial e
Solderless connections; part 2: solderless crimped connections; general requirements, test methods and practical guidance
Supplement to ANSI Y32.2-75 and IEEE 315-75 R(1994)
Supplement to Graphic Symbols for Electrical and Electronics Diagrams (Supplement to ANSI Y32.2-75 and IEEE 315-75)
Fire hazard testing. Part 1 : Guidance for the preparation of requirements and test specifications for assessing fire hazard of electrotechnical products. Guidance for use of preselection procedures
Electrical engineering; basic environmental testing procedures; guidance to test Kc: sulphur dioxide SO2 (high concentration) for electrical contacts and connections; indentical with IEC 68-2-49, edition 1983
Electrical ingeneering; basic environmental testing procedures; tests; guidance to test Kd: hydrogen sulphide H2S (high concentration) for electrical contacts and connections; identical with IEC 60068-2-46, edition 1982
British Standard Glossary of Electrotechnical, power, telecommunication, electronics, lighting and colour terms Committees responsible Guide to the glossary Foreword Glossary 202 1 General terms 202 2 Electronic power convertors and electronic power switches 202 3 Essential components 202 4 Circuits 202 5 Operations 202 6 Characteristics 202 7 Characteristic curves (of convertors) Alphabetical index
Glossary of electrotechnical, power, telecommunication, electronics, lighting and colour terms - Terms particular to power engineering - Power electronics terminology
Glossary of Electrotechnical, power, telecommunication, electronics, lighting and colour terms Committees responsible Guide to the glossary Foreword Glossary 101 1 Mathematics 101 11 Concepts related to fields 101 12 Concepts related to data handling 101 13 Concepts related to distribution and integral transformation 101 14 Concepts related to time-dependent quantities 101 15 Concepts related to waves 101 16 Concepts related to information theory 101 2 Physics and chemistry 101 21 Physical concepts 101 22 Electrochemical concepts 101 23 Concepts related to quantities and units 101 3 Electromagnetism 101 31 Electromagnetic concepts and quantities 101 32 Electromagnetic properties of materials 101 33 Electric conductors 101 4 Electric and magnetic circuits 101 41 General 101 42 Topology of electric networks 101 43 Performance of electric networks 101 44 Polyphase circuits and components Appendix Usual systems of components Alphabetical index
Glossary of electrotechnical, power, telecommunication, electronics, lighting and colour terms - Terms common to power, telecommunications and electronics - Fundamental terminology
Fire hazard testing. Part 1 : Guidance for the preparation of requirements and test specifications for assessing fire hazard of electrotechnical products. General Guidance
Intended to provide additional graphic symbols and information on internationally approved graphic symbols needed for use for all electrical and electronics diagrams except for those required for logic circuit diagrams, architectural plans and street maps, and building system layouts for cable TV applications.
Graphic Symbols for Electrical and Electronics Diagrams (Including Reference Designation Class Designation Letters) CSA Z99-75; Includes supplement to ANSI Y32.2-75 and IEEE 315-75
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号