L13 电阻器 标准查询与下载

BS EN 140401-804:2011 详细规范.固定低功率膜SMD电阻器.矩形.稳定性等级0.1;0.25

Detail Specification. Fixed low power film high stability SMD resistors. Rectangular. Stability classes 0,1; 0,25

Detail Specification. Fixed low power film high stability SMD resistors. Rectangular. Stability classes 0,1; 0,25

BS EN 140401-804:2011+A1:2013 详细规范.固定低功率膜SMD电阻器.矩形.稳定性等级0.1;0.25

Detail Specification: Fixed low power film high stability SMD resistors. Rectangular. Stability classes 0,1; 0,25

DIN EN 140401-803:2011 详细规范:低功率表面安装设备(SMD)的固定薄膜电阻器.圆柱形.稳定等级为0.05、0.1、0.25、0.5、1和2.德文版本EN 140401-803-2007 + A1-2010

Detail specification: Fixed low power film SMD resistors - Cylindrical - Stability classes 0,05; 0,1; 0,25; 0,5; 1; 2; German version EN 140401-803:2007 + A1:2010

DIN EN 140401-802:2011 详细规范:低功率表面安装设备(SMD)的固定薄膜电阻器.矩形.稳定性级别1和2.德文版本EN 140401-802-2007 + A1-2010

Detail specification: Fixed low power film SMD resistors - Rectangular - Stability classes 1; 2; German version EN 140401-802:2007 + A1:2010

DIN EN 60539-2:2011 直热式负温度系数热敏电阻器.第2部分:分规范.表面安装负温度系数热敏电阻器(IEC 60539-2-2003 + A1-2010).德文版本EN 60539-2-2004 + A1-2010

Directly heated negative temperature coefficient thermistors - Part 2: Sectional specification - Surface mount negative temperature coefficient thermistors (IEC 60539-2:2003 + A1:2010); German version EN 60539-2:2004 + A1:2010

JIS C 5201-1:2011 电子设备用固定电阻器.第1部分:总规范

This Standard is a generic specification and is applicable to fixed resistors for use in electronic equipment (hereafter referred to as "resistors"). This Standard establishes standard terms, inspection procedures and methods of test for use in sectional and detail specifications of electronic components for quality assessment or any other purpose.

Fixed resistors for use in electronic equipment -- Part 1: Generic specification

ASTM F390-11 用共线四探针法测定金属薄膜的薄膜电阻的标准试验方法

1.1 This test method covers the measurement of the sheet resistance of metallic thin films with a collinear four-probe array. It is intended for use with rectangular metallic films between 0.01 and 100 [mu]m thick, formed by deposition of a material or by a thinning process and supported by an insulating substrate, in the sheet resistance range from 10 to 10 [omega]/[open-box] (see 3.1.3). 1.2 This test method is suitable for referee measurement purposes as well as for routine acceptance measurements. 1.3 The values stated in Si units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Sheet Resistance of Thin Metallic Films With a Collinear Four-Probe Array

IEC 60539-2:2010 直热式负温度系数热敏电阻器.第2部分:分规范.表面安装负温度系数热敏电阻器

This part of IEC 60539 is applicable to surface mount directly heated negative temperature coefficient thermistors, typically made from transition metal oxide materials with semiconducting properties. These thermistors have metallized connecting pads or soldering strips and are intended to be mounted directly on to substrates for hybrid circuits or on to printed boards.

Directly heated negative temperature coefficient thermistors - Part 2: Sectional specification - Surface mount negative temperature coefficient thermistors

DIN EN 140101-806 Berichtigung 1:2010 详细规范:低功率薄膜固定电阻器.高级陶瓷上保护涂覆或模塑、轴向或预制导线的金属薄膜电阻器.德文版本EN 140101-806-2008,勘误表DIN EN 140101-806-2008.德文版本CENELEC-Cor.-2009 EN 140101-806-2008

This corrigendum corrected table 6 - Climatic categories.

Detail Specification: Fixed low power film resistors - Metal film resistors on high grade ceramic, conformal coated or molded, axial or preformed leads; German version EN 140101-806:2008, Corrigendum to DIN EN 140101-806:2008-08; German version CENELEC-Co

KS C 1614-2009 电阻式电子温度计

이 표준은 KS C 1603에 규정한 측온 저항체의 저항값을 입력으로 하는 저항식 디지털

Resistance digital thermometer

DIN EN 140401:2009 空白详细规范:表面安装固定低功率膜(SMD)电阻器,德文版本 EN 140401:2009

Blank Detail Specification: Fixed low power film surface mount (SMD) resistors; German version EN 140401:2009

BS EN 140401:2009 空白详细规范.低功率膜表面安装固定(SMD)电阻器

A blank detail specification is a supplementary document to the sectional specification and contains requirements for style and layout and minimum content of detail specifications. Detail specifications not complying with these requirements shall not be considered as being in accordance with European standards nor shall they be so described. In the preparation of the detail specification the content of EN 140400:2003, 1.2 shall be taken into account. The detail specification should be written by using the preferred values given in EN 140400. The detail specification should contain a table of contents prior the first page of the actual specification. For the use of SI units refer to ISO 1000, for the use of letter symbols to be used in electrical technology, refer to EN 60027-1. Notes in this document shall be considered as guidance and are not part of the detail specification itself.

Blank Detail Specification - Fixed low power film surface mount (SMD) resistors

IEC 60738-1:2009 热敏电阻器.直热式正温度系数.第1部分:通用规范

Thermistors - Directly heated positive temperature coefficient - Part 1: Generic specification

DIN EN 62319-1 Berichtigung 1:2009 聚合热敏电阻.直接加热的阳极阶跃函数温度系数.第1部分:一般规范(IEC 62319-1-2005).德文版本EN 62319-1-2005.勘误表DIN EN 62319-1(VDE 0898-1)-2005-11

Polymeric thermistors - Directly heated positive step function temperature coefficient - Part 1: Generic specification (IEC 62319-1:2005); German version EN 62319-1:2005, Corrigendum to DIN EN 62319-1 (VDE 0898-1):2005-11

GJB 6787-2009 含宇航级零欧姆片式膜固定电阻器通用规范

本规范对含宇宙级零欧姆片式膜固定电阻器（以下简称电阻器）的通用要求进行了规定。本规范规定了三种质量等级的产品：100%筛选的宇航级“T”等级产品；100%筛选的“H”等级产品；采用承制方检验体系来验证产品一致性的“C”等级产品。

Resistors,chip,fixed,film,zero,ohm,including space level,general specification for

GJB 1432B-2009 片式膜固定电阻器通用规范

本规范规定了无失效率等级、有失效率等级和宇航级的片式膜固定电阻器的通用要求。 本规范适用于在各种严酷环境条件下具有稳定性的无失效率等级、有失效率等级和宇航级的片式膜固定电阻器(以下简称电阻器)。

Resistors,chip,fixed,film,general specification for

GJB 6786-2009 含宇航级功率型线绕固定电阻器通用规范

本规范规定了有、无失效率等级(c)及宇航级(T)轴向功率型线绕固定电阻器的通用要求。C等级产品的鉴定以六级失效率等级产品的鉴定为基础。T级产品的鉴定以八级失效率等级的鉴定为基础。 本规范适用于在25°的环境温度中正常工作，并在250°时降为10%的额定功耗使用的功率型线绕固定电阻器(以下简称电阻器)。

Resistors,fixed,wire wound power type,including space level general specification for

IEC 61051-2:1991/AMD1:2009 电子设备用压敏电阻器.第2部分:浪涌抑制压敏电阻器的分规范.修改件1

This standard is applicable to surge suppression varistors intended to protect electronic and other sensitive equipment from surges@ operating from a d.c. supply@ or an a.c. supply having a frequency not greater than 400 Hz. Varistors which are the subject of this sectional specification are not intended to give primary protection against lightning surges.

Varistors for use in electronic equipment - Part 2: Sectional specification for surge suppression varistors; Amendment 1

IEC 60738-1:2006/AMD1:2009 热敏电阻.直热式正温度系数.第1部分:总规范.修改件1

This part of IEC 60738 describes terms and methods of test for positive step-function temperature coefficient thermistors@ insulated and non-insulated types typically made from ferro-electric semi-conductor materials. It establishes standard terms@ inspection procedures and methods of test for use in detail specifications for Qualification Approval and for Quality Assessment Systems for electronic components.

Thermistors - Directly heated positive temperature coefficient - Part 1: Generic specification; Amendment 1

DIN EN 61051-1:2009 电子设备用电阻器 第1部分:一般规范

Varistors for use in electronic equipment - Part 1: Generic specification (IEC 61051-1:2007); German version EN 61051-1:2008