共找到 294 条与 滤波器、延迟线 相关的标准,共 20 页
Geometrical product specifications (GPS) - Filtration - Part 85: Morphological areal filters: Segmentation (ISO 16610-85:2013); German version EN ISO 16610-85:2013
Radio frequency (RF) bulk acoustic wave (BAW) filters of assessed quality - Part 2: Guidelines for the use (IEC 62575-2:2012); German version EN 62575-2:2012
Passive RF and microwave devices, intermodulation level measurement. General requirements and measuring methods
Passive RF and microwave devices, intermodulation level measurement. Measurement of passive intermodulation in antennas
Passive RF and microwave devices, intermodulation level measurement. Measurement of passive intermodulation in coaxial cable assemblies
Passive RF and microwave devices, intermodulation level measurement. Measurement of passive intermodulation in filters
Passive RF and microwave devices, intermodulation level measurement - Part 3: Measurement of passive intermodulation in coaxial connectors (IEC 62037-3:2012); German version EN 62037-3:2012
Passive RF and microwave devices, intermodulation level measurement - Part 4: Measurement of passive intermodulation in coaxial cables (IEC 62037-4:2012); German version EN 62037-4:2012
This part of ISO 16610 develops the terminology and concepts for areal morphological segmentation. In particular, it describes the watershed segmentation method and the Wolf pruning method. This document assumes a continuous surface.
Geometrical product specifications (GPS) - Filtration - Part 85: Morphological areal filters: Segmentation
Standard for Safety for Electromagnetic Interference Filters, Bulletin dated September 21, 2012
Standard for Safety for Electromagnetic Interference Filters (Bulletin dated April 27, 2012)
This part of IEC 62037 defines a procedure to measure levels of passive intermodulation generated by a coaxial cable assembly. This test method is applicable to jumper cables@ i.e. cable assemblies intended to provide interface flexibility between rigid devices.
Passive r.f. and microwave devices, Intermodulation level measurement - Part 2: Measurement of passive intermodulation in coaxial assemblies
Radio frequency (RF) bulk acoustic wave (BAW) filters of assessed quality. Guidelines for the use
Surface Acoustic Wave (SAW) and Bulk Acoustic Wave (BAW) duplexers of assessed quality - Part 2: Guidelines for the use (IEC 62604-2:2011); German version EN 62604-2:2012
This part of IEC 62575 gives practical guidance on the use of RF BAW filters which are used in telecommunications@ measuring equipment@ radar systems and consumer products. General information@ standard values and test conditions will be provided in a future IEC standard1. This part of IEC 62575 includes various kinds of filter configurations@ of which the operating frequency range is from approximately 500 MHz to 10 GHz and the relative bandwidth is about 1 % to 5 % of the centre frequency. 1 This standard (under consideration) is expected to bear the reference number IEC 62575-1.
Radio frequency (RF) bulk acoustic wave (BAW) filters of assessed quality - Part 2: Guidelines for the use
This part of IEC 60862 gives practical guidance on the use of SAW filters which are used in telecommunications@ measuring equipment@ radar systems and consumer products. IEC 60862-1 should be referred to for general information@ standard values and test conditions. SAW filters are now widely used in a variety of applications such as TV@ satellite communications@ optical fibre communications@ mobile communications and so on. While these SAW filters have various specifications@ many of them can be classified within a few fundamental categories. This part of IEC 60862 includes various kinds of filter configuration@ of which the operating frequency range is from approximately 10 MHz to 3 GHz and the relative bandwidth is about 0@02 % to 50 % of the centre frequency. It is not the aim of this standard to explain theory@ nor to attempt to cover all the eventualities which may arise in practical circumstances. This standard draws attention to some of the more fundamental questions@ which should be considered by the user before he places an order for a SAW filter for a new application. Such a procedure will be the user's insurance against unsatisfactory performance. Standard specifications@ given in IEC 60862 series@ and national specifications or detail specifications issued by manufacturers@ define the available combinations of nominal frequency@ pass bandwidth@ ripple@ shape factor@ terminating impedance@ etc. These specifications are compiled to include a wide range of SAW filters with standardized performances. It cannot be over-emphasized that the user should@ wherever possible@ select his SAW filters from these specifications@ when available@ even if it may lead to making small modifications to his circuit to enable standard filters to be used. This applies particularly to the selection of the nominal frequency.
Surface acoustic wave (SAW) filters of assessed quality - Part 2: Guide for the use
Methods of measurement of the suppression characteristics of passive EMC filtering devices (CISPR 17:2011); German version EN 55017:2011
Surface Acoustic Wave (SAW) and Bulk Acoustic Wave (BAW) duplexers of assessed quality. Guidelines for the use
本规范规定了SBP75、SBP80、SBP270、SBP275型声表面波带通滤波器(以下简称滤波器)的详细要求。
Detail specification for type SBP75、SBP80、SBP270、SBP275 surface acoustic wave band-pass filters
General Specifications for Mechanical Filters
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号