L25 继电器、斩波器 标准查询与下载

GJB 65/4-2011 JRW-3M型密封电磁继电器详细规范

本规范规定了JRW-3M型密封电磁继电器（以下简称继电器）的详细要求。

Detail specification for model JRW-3M hermetically sealed,electromagnetic,relays

GJB 65/15-2011 2JRXM-1型电磁继电器详细规范

本规范规定了2JRXM-1型电磁继电器（以下简称继电器）的详细要求。

Detail specification for model 2JRXM-1 electromagnetic relays

BS EN 60255-22-5:2011 量度继电器和保护装置.电气干扰试验.涌抗扰度测试

This part of IEC 60255 is based on IEC 61000-4-5, referring to that publication where applicable, and specifies the general requirements for surge immunity tests for measuring relays and protection equipment for power system protection, including the control, monitoring and process interface equipment used with those systems. The objective of the tests is to confirm that the equipment under test will operate correctly when energized and subjected to high-energy disturbances on the power and interconnection lines, caused by surge voltages from switching and lightning effects. This standard does not intend to test the capability of the insulation to withstand high-voltage stress. The insulation test is covered by IEC 60255-27. The requirements specified in this standard are applicable to measuring relays and protection equipment in a new condition and all tests specified are type tests only. The object of this standard is to define: ? terms used; ? test severity levels; ? test equipment; ? test set-up; ? test procedures; ? criteria for acceptance; ? test report requirements.

Measuring relays and protection equipment. Electrical disturbance tests. Surge immunity test

JJF 1282-2011 电子式时间继电器校准规范

本规范规定了电子式时间继电器（以下简称时间继电器）的计量特性、校准条件、校准项目和校准方法，适用于时间继电器的校准。其他类型时间继电器的校准可参照本规范进行。

Calibration Specification for Electronic time relay

IEC 61810-2-1:2011 机电式初级继电器.第2-1部分:可靠性.B10值的确认规程

This part of IEC 61810 specifies reliability test procedures for electromechanical elementary relays when enhanced requirements for the verification of reliability apply. Particular provisions are given for relays incorporated in safety-related control systems of machinery in accordance with IEC 62061 and ISO 13849-1. For such relays B10 values for dangerous failures (B10d values) are derived from the tests specified in this standard. This International Standard is only intended to be used in conjunction with IEC 61810-2.

Electromechanical elementary relays - Part 2-1: Reliability - Procedure for the verification of B10 values

IEC 61810-2:2011 机电式初级继电器.第2部分:可靠性

"This part of IEC 61810 covers test conditions and provisions for the evaluation of endurance tests using appropriate statistical methods to obtain reliability characteristics for relays. It should be used in conjunction with IEC 61649. This International Standard applies to electromechanical elementary relays considered as non-repaired items (i.e. items which are not repaired after failure)@ whenever a random sample of items is subjected to a test of cycles to failure (CTF). The lifetime of a relay is usually expressed in number of cycles. Therefore@ whenever the terms ""time"" or ""duration"" are used in IEC 61649@ this term should be understood to mean ""cycles"". However@ with a given frequency of operation@ the number of cycles can be transformed into respective times (e.g. times to failure (TTF)). The failure criteria and the resulting characteristics of elementary relays describing their reliability in normal use are specified in this standard. A relay failure occurs when the specified failure criteria are met. As the failure rate for elementary relays cannot be considered as constant@ particularly due to wear-out mechanisms@ the times to failure of tested items typically show a Weibull distribution. This standard provides both numerical and graphical methods to calculate approximate values for the two-parameter Weibull distribution@ as well as lower confidence limits."

Electromechanical elementary relays - Part 2: Reliability

IEC 60255-127:2010 量度继电器和保护装置.第127部分:过/欠电压保护的功能要求

This part of IEC 60255 specifies minimum requirements for over/under voltage relays. The standard includes specification of the protection function, measurement characteristics and time delay characteristics. This standard defines the influencing factors that affect the accuracy under steady state conditions and performance characteristics during dynamic conditions. The test methodologies for verifying performance characteristics and accuracy are also included in this standard.

Measuring relays and protection equipment - Part 127: Functional requirements for over/under voltage protection

IEC 61810-1:2008/COR1:2010 机电式初级继电器.第1部分:一般要求

Electromechanical elementary relays - Part 1: General requirements

IEC 60255-1:2009 测量继电器和保护设备.第1部分:通用要求

This part of IEC 60255 specifies common rules and requirements applicable to measuring relays and protection equipment including any combination of devices to form schemes for power system protection such as control@ monitoring and process interface equipment in order to obtain uniformity of requirements and tests. All measuring relays and protection equipment used for protection within the power system environment are covered by this standard. Other standards in this series may define their own requirements which in such cases shall take precedence. For special applications (marine@ aerospace@ explosive atmospheres@ computers@ etc.)@ the general requirements within this standard may need to be enhanced by additional special requirements. The requirements are applicable only to relays in new condition. All tests in this standard are type tests@ unless otherwise declared.

Measuring relays and protection equipment - Part 1: Common requirements

IEC 60255-151:2009 测量继电器和保护设备.第151部分:过/欠电流保护的功能要求

Measuring relays and protection equipment - Part 151: Functional reuirements for over/under current protection

GJB 1513A-2009 混合和固体延时继电器通用规范

本规范规定了混合和固体延时继电器(以下简称继电器)的通用要求。这些继电器由混合集成电路、固体电子器件和一个电磁继电器或固体输出电路组合而成。 本规范适用于航天、航空和相关地面支持电气和电子系统及设备用继电器(见6.1)。

Relays,hybrid and solid state,time delay,general specification for

NF E17-901-5:2009 仪表和仪表远程读数用通信系统.第5部分:无线继电器

Communication systems for meters and remote reading of meters - Part 5 : wireless relaying.

DIN EN 60255-6 Berichtigung 1:2008 继电器.第6部分:测量继电器和保护设备(修改的IEC 60255-6-1988).技术勘误DIN EN 60255-6(VDE 0435-301)-1994-11

Electrical relays - Part 6: Measuring relays and protection equipment (IEC 60255-6:1988, modified); German version EN 60255-6:1994, Corrigendum to DIN EN 60255-6 (VDE 0435-301):1994-11; German version CENELEC-Cor.:1995 to EN 60255-6:1994

NF C45-200-22-4:2008 测量继电器和保护设备 第22-4部分 电干扰试验 电气快速瞬变/脉冲抗扰性试验

Measuring relays and protection equipment - Part 22-4 : electrical disturbance tests - Electrical fast transient/burst immunity test.

IEC 60255-26:2008 测量继电器和保护设备.第26部分:电磁兼容性要求

This part of IEC 60255 is applicable to measuring relays and protection equipment for power system protection, including the control, monitoring and process interface equipment used with those systems. This standard specifies the essential requirements for electromagnetic compatibility for measuring relays and protection equipment intended to be used at industrial locations. Measuring relays and protection equipment used in substations and power plants may require higher immunity test levels. For equipment not incorporating electronic circuits, for example electromechanical relays, tests according to this standard are not required. The requirements specified in this standard are applicable to measuring relays and protection equipment in a new condition and all tests specified are type tests only.

Measuring relays and protection equipment - Part 26: Electromagnetic compatibility requirements

NF C45-200-22-1:2008 测量继电器和保护设备.第22-1部分:电气干扰试验.1MHz脉冲抗扰性试验

Measuring relays and protection equipment - Part 22-1 : electrical disturbance tests - 1 MHz burst immunity tests.

SJ 50065/15-2008 JMW-270M型有可靠性指标的TO-5密封磁保持继电器详细规范

本规范规定了触点电流从低电平至1.OA、两组转换触点、有可靠性指标、TO-5封装的密封磁保持继电器的详细要求。

Detail specification for model JMW-270M, TO-5, hermetically sealed magnetic Latching relays, established reliability

SJ 51513/2-2008 JSB-42M型密封混合延时继电器详细规范

本规范规定了延时（0.1～600）s,触点电流（0.1～2）A, 两组转换触点的密封混合延时继电器的详细要求。 该型继电器符合GJB 1513-1992的1型A类规定，质量等级为Y级或X级。

Detail specification for model JSB-42M, hermetically sealed, hybrid and time delay relays

SJ 50065/14-2008 JRW-230M型有可靠性指标的TO-5密封直流电磁继电器详细规范

本规范规定了触点电流从低电平至1.OA、两组转换触点、有可靠性指标、T0-5封装的密封直流电磁继电器的详细要求。

Detail specification for model JRW-230M, TO-5, hermetically sealed, d.c. electromagnetic relays, established reliability

IEC 60255-22-2:2008 测量继电器和保护设备.第22-2部分:电干扰试验.静电放电试验

This part of IEC 60255-22 is based on IEC 61000-4-2, referring to that publication where applicable, and specifies the general requirements for electrostatic discharge tests for measuring relays and protection equipment for power system protection, including the control, monitoring and process interface equipment used with those systems. The object of the tests is to confirm that the equipment being tested will not maloperate when energized and subjected to an electrostatic discharge. The requirements are applicable only to relays and protection equipment in new condition, and all tests specified are type tests only.

Measuring relays and protection equipment - Part 22-2: Electrical disturbance tests - Electrostatic discharge tests