共找到 336 条与 波导同轴元件及附件 相关的标准,共 23 页
Detail Specification for Type GBX007 Miniature Waveguide RF Isolators
This is Amendment 1 to IEC 60154-2-1980 (Flanges for waveguides - Part 2: Relevant specifications for flanges for ordinary rectangular waveguides)
Flanges for waveguides - Part 2: Relevant specifications for flanges for ordinary rectangular waveguides; Amendment 1
This part of IEC 61580 is applicable to the variation of group delay of a wave propagated in waveguide or waveguide assemblies. The objective of the test procedures given below is to characterize the group delay variation of a wave propagated in waveguide or waveguide assemblies.
Methods of measurement for waveguides - Part 3: Variation of group delay
The document describes the measurement of the power holding of a waveguide by the use of a multiplying loop.
Methods of measurement for waveguides - Part 8: Waveguide power holding capability (IEC 61580-8:1996); German version EN 61580-8:1996
The document gives the means for determining the reflection coefficient at the junction of two similar rectangular waveguides due to imperfections.
Methods of measurement for waveguides - Part 9: Reflection coefficient at rectangular waveguide interfaces (IEC 61580-9:1996); German version EN 61580-9:1996
The document is applicable to waveguide performance.
Methods of measurement for waveguides - Part 7: Graphic method for the determination of waveguide performance (IEC 61580-7:1996); German version EN 61580-7:1996
The document is applicable to intermodulation products in waveguides.
Methods of measurement for waveguides - Part 2: Level of intermodulation products (IEC 61580-2:1996); German version EN 61580-2:1996
The document is applicable to waveguides which can propagate two orthogonal polarizations of the same waveguide mode.
Methods of measurement for waveguides - Part 1: Decoupling and rotation of the plane of polarization (IEC 61580-1:1996); German version EN 61580-1:1996
Describes the measurement of the power holding of a waveguide by the use of the multiplying loop.
Methods of measurement for waveguides. Waveguide power holding capability
Gives test procedures to characterize the level of unwanted signals caused by the presence of two or more transmitting signals in waveguides or waveguide assemblies.
Methods of measurement for waveguides. Level of intermodulation products
Gives test procedures which characterize the cross-polar properties of waveguides.
Methods of measurement for waveguides. Decoupling and rotation of the plane of polarization
Gives the means of determining the reflection coefficient at the junction of two similiar rectangular waveguides due to imperfections in internal dimensions, lateral displacement and angular misalignment.
Methods of measurement for waveguides. Reflection coefficient at rectangular waveguide interfaces
Provides a means for determining the cut-off frequencies for the dominant and higher order modes of frequency range 1 GHz to 27 GHz.
Methods of measurement for waveguides. Graphical method for the determination of waveguide performance
1.1 This specification covers seamless copper and copper-alloy rectangular tube intended for use as transmission lines in electronic equipment. Four types of material are specified having the following nominal compositions:Copper or Copper Alloy UNS No. Previously Used DesignationNominal Composition, % Copper ZincPhos- phorusC10200Copper, Type OF100......C10300...99.99...0.003C12000Copper, Type DLP100......C22000Commercial bronze, 90 %9010... Types OF and DLP are described in Classification B 224.1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
Standard Specification for Seamless Copper and Copper-Alloy Rectangular Waveguide Tube
1.1 This specification covers seamless copper and copper-alloy rectangular tube intended for use as transmission lines in electronic equipment. Four types of material are specified having the following nominal compositions: Copper or Nominal Composition, % Copper Alloy Previously Phos- UNS 2 No. Used Designation Copper Zinc phorus C10200 Copper, Type OF A 100 ... ... C10300 ... 99.99 ... 0.003 C12000 Copper, Type DLP A 100 ... ... C22000 Commercial 90 10 ... bronze, 90% A Types OF and DLP are described in Classification B 224. 1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
Standard Specification for Seamless Copper and Copper-Alloy Rectangular Waveguide Tube
Relates to the dimension of waveguide flanges for use in electronic equipment. It covers the requirements for flanges drilled before or after mounting on waveguides.
Flanges for waveguides - General requirements
Type GW9005 and GW9006 radio frequency micro strip isolator detail specification for
Type GTP015A and GTP029A radio frequency strip-line isolators detail specification for
Type GTP002B radio frequency coaxial isolators detail specification for
detail specification for Type GTP032A radio frequency coaxil isolators
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号