L47 其他 标准查询与下载

GB/T 12850-1991 计算器用扭曲向列型液晶显示器件空白详细规范(可供认证用)

本空白详细规范适用于计算器用扭曲向列型液晶显示器件。它与GBT12848《扭曲向列型液晶显示器件总规范》一起使用。它规定了详细规范采用的格式和包括的内容。

Blank detail specification of twisted nematic liquid crystal displays for calculators

GB/T 12849-1991 钟、表用扭曲向列型液晶显示器件空白详细规范(可供认证用)

本空白详细规范适用于钟、表用扭曲向列型液晶显示器件。它与GB/T12848《扭曲向列型液晶显示器件总规范》一起使用。它规定了详细规范采用的格式和包括的内容。

Blank detail specification of twisted nematic liquid crystal displays for watches

GB/T 12848-1991 扭曲向列型液晶显示器件总规范(可供认证用)

本规范规定了扭曲向列型液晶显示器件质量评定的程序，并给出了电光参数、机械、环境和耐久性的测试和试验方法。 本规范适用于扭曲向列型液晶显示器件（以下简称显示器件）。本规范由空白详细规范进一步补充。

Generic specification of twisted nematic liquid crystal display devices

IEC 62629-1-2:2021 三维显示设备. 第1-2部分: 通用类. 术语和文字符号

This part of IEC 62629 provides a list of the terminologies that are frequently used in describing 3D display technologies in the IEC 62629 series. Terms for various 3D display technologies on stereoscopic, autostereoscopic, volumetric, and holographic displays are included.

3D display devices - Part 1-2: Generic - Terminology and letter symbols

SJ/T 11460.4-2018 液晶显示用背光组件 第4部分：量子点背光组件空白详细规范

Backlight components for liquid crystal displays Part 4: Blank detailed specification for quantum dot backlight components

IEC 62595-2-3:2018 显示照明装置.第2-3部分:LED前照灯单元的光电测量方法

This part of IEC 62595 specifies the standard measurement conditions and measuring methods for determining electrical, optical, and electro-optical properties of LED frontlight units (FLUs) for reflective displays. NOTE: See 3. for a definition of reflective display.

Display lighting unit - Part 2-3: Electro-optical measuring methods for LED frontlight unit

IEC 61747-40-6:2018 液晶显示装置.第40-6部分:移动设备用显示保护玻璃的机械试验.双轴抗弯强度（环磨损环）

This part of IEC 61747 is a mechanical performance testing procedure for cover glass used in electronic flat panel displays in mobile devices. This document focuses on the measurement of surface fracture load after flaw introduction via grit particle abrasion. After abrasion, the retained surface fracture load is measured with the method documented in IEC 61747-40-4.

Liquid crystal display devices - Part 40-6: Mechanical testing of display cover glass for mobile devices - Retained biaxial flexural strength (abraded ring-on-ring)

SJ/T 11141-2017 发光二极管(LED)显示屏通用规范

本规范规定了LED显示屏的术语和定义、分类、技术要求、检验方法、检验规则，以及标志、包装、运输和贮存要求。 本规范适用于LED显示屏产品。

Generic specification for LED displays

SJ/T 11281-2017 发光二极管(LED)显示屏测试方法

本标准规定了发光二极管(LED)显示屏的机械、光学、电学等主要技术性能参数的测试方法。 本标准适用于发光二极管(LED)显示屏(以下简称显示屏)的测试。

Measure methods of light emitting diode (LED) displays

IEC 62908-12-10:2017 触控和交互显示. 第12-10部分: 触控显示的测量方法. 触控和电气性能

This part of IEC 62908 specifies the standard measuring conditions and methods for determining touch performance of a touch sensor module. This document is applicable to touch sensor modules, where the structural relationship between touch sensor, touch controller, touch sensor module, display panel, touch display panel, and touch display module is defined in IEC 62908-1-2.

Touch and interactive displays - Part 12-10: Measurement methods of touch displays - Touch and electrical performance

IEC 62715-5-1:2017 柔性显示设备-第5-1部分：光学性能的测量方法

This part of IEC 62715 specifies the standard measuring conditions and measuring methods for determining the optical performance of flexible displays in the dark or under ambient illumination. This document mainly applies to display modules that are bendable about one axis. The display is measured in a static mechanical state. The measuring methods apply to monochrome or colour displays with a single radius of curvature of 35 mm or greater.

Flexible display devices - Part 5-1: Measuring methods of optical performance

IEC 62715-5-3:2017 软性显示装置. 第5-3部分: 图像质量和缺陷的视觉评估

This part of IEC 62715 provides the framework and procedures for performing the visual assessment of flexible display devices. Visual assessment stipulated in this document is applicable to flexible display modules in the following states: initial states and ageing states under standard ambient conditions; mechanically or environmentally stressed conditions; states after mechanical endurance test(s), after environmental endurance test(s) and after a combination of mechanical and environmental endurance tests. NOTE Visual assessment under the mechanical or environmental stress is usually difficult to do, but this document can be applied when it is possible. Visual assessment is performed by comparing a test sample to a limit sample or to a set of grade samples. This document provides the framework and procedures for visual assessments that use a limit sample or a set of grade samples. This document describes the framework and procedure that are followed while preparing limit samples and a set of grade samples. This document also describes visual assessment when limit samples and grade samples are not available for the same type of defect. This document provides sets of test patterns that can be used in visual assessments.

Flexible display devices - Part 5-3: Visual assessment of image quality and defects

IEC 62715-6-2:2017 软性显示装置. 第6-2部分: 环境试验方法

This part of IEC 62715 specifies testing methods for evaluating the environmental endurance of flexible display panels and modules for use, storage and transport under assumed usage environment. This part of IEC 62715 is applicable to flexible display panels and modules such as liquid crystal display devices (LCDs), electric paper display devices (EPDs), and organic light emitting diode display devices (OLEDs). This part of IEC 62715 will also be suitable for flexible panel or module with mechanical operation.

Flexible display devices - Part 6-2: Environmental testing methods

BS IEC 62908-13-10:2016 触摸和交互式显示器 触摸显示器的可靠性测试方法 环境耐久性试验方法

Touch and interactive displays. Reliability test methods of touch displays. Environmental durability test methods

IEC 62908-13-10:2016 触摸和交互式显示器 第 13-10 部分：触摸显示器的可靠性测试方法 环境耐久性测试方法

This part of IEC 62908 specifies the methods for testing the environmental durability of touch display modules, touch sensor modules and test pattern cells, and can be used for devices at the production level, the prototype level or the trial model level when they are exposed to environmental stress. This document is applicable for touch displays that use capacitive or resistive detection sensors. It may also be applicable to other types of sensors as well as to touch display modules with both flat and flexible displays.

Touch and interactive displays - Part 13-10: Reliability test methods of touch displays - Environmental durability test methods

SJ/T 11461.6.2-2016 有机发光二极管显示器件 第6-2部分：测试方法-视觉质量

Organic light-emitting diode display devices Part 6-2: Test methods - Visual quality

BS IEC 62679-4-2:2016 电子纸显示器. 环境试验方法

Electronic paper displays. Environmental test methods

IEC 62679-3-3:2016 电子纸显示器. 第3-3部分: 带集成照明装置的显示器光学测量方法

This part of IEC 62679 specifies the standard measurement conditions and measurement methods for determining the optical performance of electronic paper display (EPD) devices which have an operating integrated lighting unit (such as a front light). The scope of this document is restricted to EPDs using segmented or matrix structures with either monochromatic or colour type displays. The measurement methods are intended for EPDs operated in a reflective mode with the integrated lighting unit (ILU) turned on in a dark or indoor ambient lighting environment. Colour systems beyond three primaries are not covered in this document.

Electronic paper displays - Part 3-3: Optical measuring methods for displays with integrated lighting units

IEC 62679-4-2:2016 电子纸显示器. 第4-2部分: 环境试验方法

This part of IEC 62679 specifies the environmental conditions to determine the environmental reliability of electronic paper display (EPD) panels and/or modules for storage under the assumed usage environment. The scope of this document is restricted to EPDs using either segment, passive, or active matrix with either monochromatic or colour type displays. The measuring methods are intended for EPDs operated in a reflective mode.

Electronic paper displays - Part 4-2: Environmental test methods

IEC 61747-30-4:2016 液晶显示装置. 第30-4部分: 液晶显示模块的测量方法. 动态背光组件

This part of IEC 61747 specifies the standard measurement conditions and measuring methods for determining the optical performance and power consumption of active matrix liquid crystal display modules with dynamic backlight units.

Liquid crystal display devices - Part 30-4: Measuring methods for liquid crystal display modules - Dynamic backlight units