共找到 952 条与 加工专用设备 相关的标准,共 64 页
Components of injection mould for plastics.Guide bushes for spacer
本标准规定了塑料注射圆锥定位件的结构尺寸、标记示例及技术要求。 本标准适用于塑料注射模各种模架的圆锥定位件
Components of injection mould for plastics.Locating elements
本标准规定了塑料注射模带螺纹顶杆的结构尺寸、标记示例及技术要求。 本标准适用于塑料注射模各种模架的带螺纹顶杆。
Components of injection mould for plastics.Ejector pins with thread
本标准规定了塑料注射模管接头的结构尺寸、标记示例及技术要求。 本标准适用于塑料注射模各种模架的管接头。
Components of injection mould for plastics.Tube fittings
本标准规定了塑料注射模斜导柱的结构尺寸、标记示例及技术要求。 本标准适用于塑料注射模各种模架的斜导柱。
Components of injection mould for plastics.Angled guide pillar
本标准规定了塑料注射模锁紧楔的结构尺寸、标记示例及技术要求。 本标准适用于塑料注射模各种模架的锁紧楔。
Components of injection mould for plastics.Wedge lock
本标准规定了塑料注射模定位螺钉的结构尺寸、标记示例及技术要求。 本标准适用于塑料注射模各种模架的定位螺钉。
Components of injection mould for plastics.Positioning screw
本标准规定了塑封模具注塑结构形式、基本尺寸、应用方式。 本标准适用于SJ/T 10515.1 塑封模具结构 典型结构规定的塑封模具。
Configuration of plastic packaged mould.Guide configuration
本标准规定了塑封模具型腔结构形式,基本尺寸、应用方式。 本标准适用于SJ/T10515.1塑封模具结构 典型结构规定的塑封模具。
Configuration of plastic packaged mould.Injection configuration
本标准规定了塑封模具导向结构形式、基本尺寸、应用方式。 本标准适用于SJ/T 10515.1塑封模具结构 典型结构规定的塑封模具。
Configuration of Plastic packaged mould.Locating configuration
本标准规定塑封模具预定位架结构形式、基本尺寸、应用方式。 本标准适用于周界为412mm×180mm~690mm×545mm的塑封模具预定位架。
Configuration of plastic packaged mould.Pre-iocating base
本标准规定了塑封模具预热装置结构形式、基本尺寸、应用方式。 本标准适用于SJ/T 10515.6 塑封模具结构 预定位架规定的塑封模具。
Configuration of plastic packaged mould.Pre-heating unit
本标准规定了塑料注射模定位止动螺钉的结构尺寸、标记示例及技术要求。 本标准适用于塑料注射模各种模架的定位止动螺钉。
Components of injection mould for plastics.Positioning stop screw
Components of injection mould for plastics.Stop Guide pillars
本标准规定了塑封模具的基本结构组合形式,尺寸系列及应用方式。 本标准适用于模板周界尺寸在487mm×265mm~775mm×630mm的塑封模具。
Configuration of plastic packaged mould.Typical configuration
Components of injection mould for plastics.Straight guide bushes
本标准规定了塑料注射模支柱的结构尺寸、标记示例及技术要求。 本标准适用于塑料注射模各种模架的支柱。
Components of injection mould for plastics.Support pillar
Components of injection mould for plastics.Shoulder guide pillars
本标准规定了塑料注射模拉料杆的结构尺寸、标记示例及技术要求。 本标准适用于塑料注射模各种模架的拉料杆。
Components of injection mould for plastics.Sprue puller
本标准规定了塑料注射模限位块的结构尺寸、标记示例及技术要求。 本标准适用于塑料注射模各种模架的限位块。
Components of injection mould for plastics.Stop block
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号