N56 环境监测仪器及其成套装置 标准查询与下载

BS EN 15267-1:2009 空气质量.自动化测量系统的证书.通用原理

This European Standard specifies the general principles, including common procedures and requirements, for the product certification of automated measuring systems (AMS) for monitoring ambient air quality and emissions from stationary sources. This product certification consists of the following sequential stages: a) performance testing of an automated measuring system; b) initial assessment of the AMS manufacturer’s quality management system; c) certification; d) surveillance. This European Standard applies to the certification of all AMS for monitoring ambient air quality and emissions from stationary sources for which performance criteria and test procedures are available in European Standards.

Air quality - Certification of automated measuring systems - Part 1: General principles

DIN EN 50402:2009 易燃或有毒气体或蒸气或氧气的探测和测量用电气设备.混合气体探测系统的功能安全要求

Electrical apparatus for the detection and measurement of combustible or toxic gases or vapours or of oxygen - Requirements on the functional safety of fixed gas detection systems; German version EN 50402:2005 + A1:2008

ANSI/UL 539-2009 单测点和多测点热报警器

Revision to proposal dated April 25, 2008.

Single and Multiple Station Heat Alarms

IEEE N323C-2009 空气监测仪器用美国国家标准化辐射防护仪表试验和校准

American National Standard Radiation Protection Instrumentation Test and Calibration Air Monitoring Instruments

ANSI/UL 2034-2009 单一和多测点一氧化碳报警器

Revisions to the following: 1. Requirement for Battery Backup and Revision to Backup Time 2. Marking Requirements for RV and Unconditioned Area CO Alarms 3. Marine Battery Temperature Requirements 4. RV Unconditioned Area Battery Temperature Requirements

Single and Multiple Station Carbon Monoxide Alarms

JJG 915-2008 一氧化碳检测报警器检定规程

本规程适用于检测非矿井作业环境中一氧化碳气体浓度的一氧化碳检测报警器（以下简称仪器）的首次检定、后续检定和使用中检验。 仪器可以分为连续性测量和非连续性测量的仪器。

Verification Regulation Carbon Monoxide Detectors

KS B 5645-2008 环境空气中悬浮粒子自动监测机

이 표준은 대기 중의 부유 입자상 물질의 농도를 연속적으로 측정하기 위한 자동 계측기(이하

Automatic moniters for suspended particulate matter in ambient air

KS B 5644-2008 环境空气中氟化合物量监测

이 표준은 대기 중의 가스 상태의 무기 플루오르 화합물 농도를 연속적으로 측정하여 플루오르

Continuous analyzers for fluorine compounds in ambient air

KS B 5646-2008 原油和石油产品中硫自动分析仪

이 표준은 원유 및 석유제품 중의 황분을 방사선을 사용하여 측정하는 자동 계측기(이하 계측

Automatic analysers for sulphur in crude oil and petroleum products

KS B 5361-2008 工业固体材料的发射率的测定

? ??? ????? ???? ?? ??1)(?? ??? ??.)? ??? ?? ??? ?

Emissivity measuring methods for industrial solid materials

JIS K 0809:2008 自动全磷分析器

This Japanese Industrial Standard specifies the performance of an automatic total phosphorus analyzer (hereafter referred to as "measuring instrument") for performing the automatic meter reading of the underwater total phosphorus concentration and its test method. NOTE : Though this Standard specifies the performance of a measuring instru- ment and its test method, it is not intended for assessing the conformity of any instrument--the performance specifications given in this Stan- dard are solely for the purpose of measurement of specific target sam" ples.

Automatic total phosphorus analyzer

JIS K 0808:2008 自动全氮分析器

This Japanese Industrial Standard specifies the performance of an automatic total ni" trogen analyzer (hereafter referred to as "measuring instrument") for performing the automatic meter reading of the total nitrogen concentration in water and its test method. NOTE : Though this Standard specifies the performance of a measuring in- strument and its test method, it is not intended for assessing the con" formity of any instrument -- the performance specifications given in this Standard are solely for the purpose of measurement of specific target samples.

Automatic total nitrogen analyzer

JIS Z 8851:2008 室温下PM2.5的取样器

この規格は，大気中に浮遊する粒子状物質のうち，PM2.5 (3.3参照)の質量濃度の測定に用いる試料採取装置(以下，サンプラという。)について規定する。

Sampler of PM2.5 in ambient air

BS EN 15267-3:2007 空气质量.自动测量系统的质量保证.固定源排放监控用自动测量系统的性能标准和试验程序

This European Standard specifies the performance criteria and test procedures for automated measuring systems that measure gases and particulate matter in, and flow of, the waste gas from stationary sources. This European Standard supports the requirements of particular EU Directives. It provides the detailed procedures covering the QAL1 requirements of EN 14181 and, where required, input data used in QAL3.

Air quality - Certification of automated measuring systems - Performance criteria and test procedures for automated measuring systems for monitoring emissions from stationary sources

JJF 1190-2008 尘埃粒子计数器校准规范

本规范适用于光散射式激光尘埃粒子计数器（以下简称粒子计数器）的校准。

Calibration Specification for Airborne Particle Counter

JIS B 7993:2008 使用非萃取方法的废气的自动测量系统

This Japanese Industrial Standard specifies the automated measuring systems (hereafter referred to as "measuring system") installed in situ which perform the long-term continuous measurement of the concentration of sulfur dioxide, nitrogen monoxide, dinitrogen monoxide, nitrogen dioxide, carbon monoxide, carbon dioxide. ammonia, hydrogen chloride, methane and moisture in the gas discharged with com- bustion of fuel and others or from various manufacturing processes etc. to a chimney or a duct in a factory and a business place using non-extractive methods. The measurement principle of this Standard shall be based on an infrared absorption method and an ultraviolet absorption method. As other measuring systems, the meas- uring system by a point method (fixed-point measurement) is given in Annex C. NOTE: The following International Standards are used as reference in this Standard. ISO 7935: 1992 Stationary source emissions- Determination of the mass concentration of su]~ur dioxide- Per~ormance characteristics of automated measuring methods ISO 10849: 1996 Stationary source emissions- Determination of the mass concentration of nitrogen oxides--Per~ormance characteristics o[' automated measuring systems

Automated measuring systems for flue gas using non-exractive methods

DIN EN 15267-3:2008 空气质量.自动测量系统的质量保证.第3部分:固定源排放监控用自动测量系统的性能标准和试验程序

This European Standard specifies the performance criteria and test procedures for automated measuring systems that measure gases and particulate matter in, and flow of, the waste gas from stationary sources. This European Standard supports the requirements of particular EU Directives. It provides the detailed procedures covering the QAL1 requirements of EN 14181 and, where required, input data used in QAL3.

Air quality - Certification of automated measuring systems - Part 3: Performance criteria and test procedures for automated measuring systems for monitoring emissions from stationary sources; English version of DIN EN 15267-3:2008-03

ASTM F2327-08 水中油检测和监测用空中远程感应系统的选择用标准指南

The contributions that an effective remote sensing system can make are: Provide a strategic picture of the overall spill, Assist in detection of slicks when they are not visible by persons operating at, or near, the water''s surface or at night, Provide location of slicks containing the most oil, Provide input for the operational deployment of equipment, Extend the hours of clean-up operations to include darkness and poor visibility, Identify oceanographic and geographic features toward which the oil may migrate, Locate unreported oil-on-water, Collect evidence linking oil-on-water to its source, Help reduce the time and effort for long range planning, A log, or time history, of the spill can be compiled from successive data runs, and A source of initial input for predictive models and for “truthing” or updating them over time.1.1 This guide provides information and criteria for selection of remote sensing systems for the detection and monitoring of oil on water. 1.2 This guide applies to the remote sensing of oil-on-water involving a variety of sensing devices used alone or in combination. The sensors may be mounted in helicopters, fixed-wing aircraft, or lighter-than-air platforms. Excluded are situations where the aircraft is used solely as a telemetry or visual observation platform and exo-atmosphere or satellite systems. 1.3 The context of sensor use is addressed to the extent it has a bearing on their selection and utility for certain missions or objectives. 1.4 This guide is generally applicable for all types of crude oils and most petroleum products, under a variety of marine or fresh water situations. 1.5 Many sensors exhibit limitations with respect to discriminating the target substances under certain states of weathering, lighting, wind and sea, or in certain settings. 1.6 This guide gives information for evaluating the capability of a remote surveillance technology to locate, determine the areal extent, as well as measure or approximate certain other characteristics of oil spilled upon water. 1.7 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.8 Remote sensing of oil-on-water involves a number of safety issues associated with the modification of aircraft and their operation, particularly at low altitudes. Also, in some instances, hazardous materials or conditions (for example, certain gases, high voltages, etc.) can be involved. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

Standard Guide for Selection of Airborne Remote Sensing Systems for Detection and Monitoring of Oil on Water

NS 9410-2007/AC-2008 技术勘误AC.海水养鱼场对深海影响的环境监测

Corrigendum AC Environmental monitoring of benthic impact from marine fish farms

HJ/T 378-2007 污染治理设施运行记录仪技术要求及检测方法

本标准规定了污染治理设施运行记录仪的技术要求、试验方法、检验规则及标志、包装、运输和贮存。 本标准适用于自动监视和记录以电为动力的各种污染治理设施运行状态的记录仪。

Technical requirement and test procedures for operation recorder of pollution treatment facility