共找到 317 条与 声学仪器与测震仪 相关的标准,共 22 页
The audiometers covered in this specification are devices designed for use in determining the hearing threshold level of an individual in comparison with a chosen standard reference threshold level. This standard provides specifications and tolerances for pure tone, speech, and masking signals and describes the minimum test capabilities of different types of audiometers.
Specification for Audiometers
This part of ISO 389 specifies test conditions for determining the hearing thresholds of subjects for the purpose of establishing standardized values for reference hearing threshold levels.
Acoustics - Reference zero for the calibration of audiometric equipment - Part 9: Preferred test conditions for the determination of reference hearing threshold levels (ISO 389-9:2009); German version EN ISO 389-9:2009
本规范适用于激光测振仪的校准。
Calibration Spectification for Laser Vibrometers
本规范适用于颗粒碰撞噪声检测系统(PIND)的校准。
Calibration Specification for PIND(Particle Impact Noise Detection)
Acoustics - Reference zero for the calibration of audiometric equipment - Part 9: Preferred test conditions for the determination of reference hearing threshold levels
Electroacoustics - Audiometric equipment - Part 7: Instruments for the measurement of auditory brainstem responses
Electroacoustics - Audiometric equipment - Part 6: Instruments for the measurement of otoacoustic emissions
为了进行飞机噪声适航审定,本标准规定了用于测量噪声的仪表系统的电声性能要求,还推荐了一些对仪器系统进行定期测试的方法,以检验设备的性能是否持续符合规定的容限要求。 一般地,一个噪声测量系统是由一系列仪器所组成的,包括传声器、记录仪、分析仪以及输出设备等。实际应用的测量系统的组成不完全一样,但是都能够以不同的方式实现所需要的功能。系统可以是模拟的,也可以是数字的。 本标准的目的是为了在规定的基准环境条件下,在规定的容限范围内,保证不同的测量系统有相同的电声特性。本标准并不提供关于安装传声器或传声器防风罩的方法 , 也不提供用于飞机噪声适航审定的有关测量和分析程序要求,而仅提供用于获得在一段时间内平均的1/3倍频带声压级测量系统的性能规范。 有些要求适用于整个测量系统,包括在分析前记录所测量的声压时间信号的方法。有些要求适用于传声器,传声器用于把所测量的声压信号转化成电信号。另外,还有些要求仅适用于分析仪,分析仪用于把信号转化成1/3倍频带声压级输出。 本标准的要求适用于测量噪声的仪表,所测噪声是由最大审定起飞重量大于900Okg的喷气式或螺旋桨驱动运输类飞机产生的,或是由安装在户外发动机试车台上的推进系统产生的。
Electroacoustics.Instruments for measurement of aircraft nois.Performance requirements for systems to measure one-third-octave band sound pressure levels in noise certincation of transport-category aeroplanes
Ultrasonics. Hydrophones. Properties of hydrophones for ultrasonic fields up to 40 MHz
Mechanical vibration and shock - Parameters to be specified for the acquisition of vibration data
Describes instruments (sound level meters) for the measurement of certain frequency-weighted and time-weighted sound pressure levels.
Sound level meters
Describes instruments for the measurement of frequency-weighted and time averaged sound pressure levels. Optionally, sound exposure levels may be measured. This standard is consistent with the relevant requirements of SANS 656, Sound level meters, but sp
Integrating-averaging sound level meters
Electroacoustics - Audiometric equipment - Part 3: Test signals of short duration (IEC 60645-3:2007); German version EN 60645-3:2007
Sound level meters. Part 1. Technical requirements
The purpose of this practice is to enable the transfer of calibration from sensors that have been calibrated by primary calibration to other sensors.1.1 This practice covers requirements for the secondary calibration of acoustic emission (AE) sensors. The secondary calibration yields the frequency response of a sensor to waves of the type normally encountered in acoustic emission work. The source producing the signal used for the calibration is mounted on the same surface of the test block as the sensor under testing (SUT). Rayleigh waves are dominant under these conditions; the calibration results represent primarily the sensor''s sensitivity to Rayleigh waves. The sensitivity of the sensor is determined for excitation within the range of 100 kHz to 1 MHz. Sensitivity values are usually determined at frequencies approximately 10 kHz apart. The units of the calibration are volts per unit of mechanical input (displacement, velocity, or acceleration). 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Practice for Secondary Calibration of Acoustic Emission Sensors
Describes procedures for periodic testing of conventional, integrating-averaging, and integrating sound level meters conforming to the class 1 or class 2 requirements of IEC 61672-1:2002 (published in South Africa as an identical adoption under the desig
Electroacoustics - Sound level meters Part 3: Periodic tests
이 규격의 첫 번째 목적은 KS A ISO 9614-1에 따라 음향파워 결정에 응용할 음의
Electroacousitics-Instruments for the measurement of sound intensity-Measurement with pairs of pressure sensing microphones
이 규격은 아래와 같은 지침 및 방법을 제시한다.― 전기적으로 전달되는 진동판이 장착된
Measurement microphones-Part 6:Electrostatic actuators for determination of frequency response
이 규격은 고막의 음압을 환산하여 100 Hz에서 10 000 Hz의 주파수 범위에서 삽입
Occluded-ear simulator for the measurement of earphones coupled to the ear by ear inserts
이 규격은 KS C IEC 61094-4에 부합하는 제거 가능한 보호망을 가진 작업용 표준
Measurement microphones-Part 5:Methods for pressure calibration of working standard microphones by comparison
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号