P16 工程防火 标准查询与下载

ASTM E84-17 建筑材料表面燃烧特性的标准试验方法

4.1 This test method is intended to provide only comparative measurements of surface flame spread and smoke density measurements with that of select grade red oak and fiber-cement board surfaces under the specific fire exposure conditions described herein. 4.2 This test method exposes a nominal 24-ft (7.32-m) long by 20-in. (508-mm) wide specimen to a controlled air flow and flaming fire exposure adjusted to spread the flame along the entire length of the select grade red oak specimen in 51/2 min. 4.3 This test method does not provide for the following: 4.3.1 Measurement of heat transmission through the tested surface. 4.3.2 The effect of aggravated flame spread behavior of an assembly resulting from the proximity of combustible walls and ceilings. 4.3.3 Classifying or defining a material as noncombustible, by means of a flame spread index by itself. 1.1 This fire-test–response standard for the comparative surface burning behavior of building materials is applicable to exposed surfaces such as walls and ceilings. The test is conducted with the specimen in the ceiling position with the surface to be evaluated exposed face down to the ignition source. The material, product, or assembly shall be capable of being mounted in the test position during the test. Thus, the specimen shall either be self-supporting by its own structural quality, held in place by added supports along the test surface, or secured from the back side. 1.2 The purpose of this test method is to determine the relative burning behavior of the material by observing the flame spread along the specimen. Flame spread and smoke developed index are reported. However, there is not necessarily a relationship between these two measurements. 1.3 The use of supporting materials on the underside of the test specimen has the ability to lower the flame spread index from those which might be obtained if the specimen could be tested without such support. These test results do not necessarily relate to indices obtained by testing materials without such support. 1.4 Testing of materials that melt, drip, or delaminate to such a degree that the continuity of the flame front is destroyed, results in low flame spread indices that do not relate directly to indices obtained by testing materials that remain in place. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 The text of this standard references notes and footnotes that provide explanatory information. These notes and footnotes, excluding those in tables and figures, shall not be considered as requirements of the standard.

Standard Test Method for Surface Burning Characteristics of Building Materials

DB11/T 1383-2016 外墙外保温防火隔离带技术规程

Technical specification for external thermal insulation and fireproof isolation belt of external wall

DIN EN 13501-4:2016 施工产品和建筑部件燃烧性能分类.第4部分:烟控制系统构件耐火性试验用数据分类.德文版本EN 13501-4-2016

Fire classification of construction products and building elements - Part 4: Classification using data from fire resistance tests on components of smoke control systems; German version EN 13501-4:2016

DIN EN 13501-2:2016 建筑产品和部件的燃烧性能分类.第2部分:通风设备除外的耐火试验数据分类.德文版本EN 13501-2-2016

Fire classification of construction products and building elements - Part 2: Classification using data from fire resistance tests, excluding ventilation services; German version EN 13501-2:2016

DIN EN 13501-5:2016 建筑产品及建筑部件的火灾种类.第5部分:对外部屋顶燃烧试验数据进行分类.德文版本EN 13501-5-2016

Fire classification of construction products and building elements - Part 5: Classification using data from external fire exposure to roofs tests; German version EN 13501-5:2016

DB54/T 0100-2016 文物建筑保护工程设计防火规范

Code for fire protection design of cultural relic building protection engineering

BS EN 13501-4:2016 建筑产品和建筑构件的防火分类 使用防烟系统组件的耐火测试数据进行分类

Fire classification of construction products and building elements. Classification using data from fire resistance tests on components of smoke control systems

BS EN 13501-2:2016 建筑产品和部件的防火等级.根据不包括通风设备的防火试验数据进行分类

Fire classification of construction products and building elements. Classification using data from fire resistance tests, excluding ventilation services

BS EN 13501-5:2016 建筑产品和建筑构件的防火分类 使用屋顶外部火灾暴露测试数据进行分类

Fire classification of construction products and building elements. Classification using data from external fire exposure to roofs tests

DIN 4102-4:2016 建筑材料和建筑构件的耐火性能.概要和分级的建筑材料、构件和特种构件的应用

Fire behaviour of building materials and building components - Part 4: Synopsis and application of classified building materials, components and special components

ISO 9705-1:2016 反应火试验. 墙壁和天花板衬里产品的房间角落试验. 第1部分: 小房间配置的试验方法

Reaction to fire tests - Room corner test for wall and ceiling lining products - Part 1: Test method for a small room configuration

SY/T 0605-2016 凝析气田地面工程设计规范

本规范适用于新建、扩建和改建的陆上凝析气田地面工程、海上凝析气田陆上终端工程。

Code for surface engineering design of gas condensate field

ASTM E119-16 建筑结构和材料防火试验的标准试验方法

4.1 These test methods are intended to evaluate the duration for which the types of building elements noted in 1.1 contain a fire, retain their structural integrity, or exhibit both properties during a predetermined test exposure. 4.2 The test exposes a test specimen to a standard fire controlled to achieve specified temperatures throughout a specified time period. When required, the fire exposure is followed by the application of a specified standard fire hose stream applied in accordance with Practice E2226. The test provides a relative measure of the fire-test-response of comparable building elements under these fire exposure conditions. The exposure is not representative of all fire conditions because conditions vary with changes in the amount, nature and distribution of fire loading, ventilation, compartment size and configuration, and heat sink characteristics of the compartment. Variation from the test conditions or test specimen construction, such as size, materials, method of assembly, also affects the fire-test-response. For these reasons, evaluation of the variation is required for application to construction in the field. 4.3 The test standard provides for the following: 4.3.1 For walls, partitions, and floor or roof test specimens: 4.3.1.1 Measurement of the transmission of heat. 4.3.1.2 Measurement of the transmission of hot gases through the test specimen. 4.3.1.3 For loadbearing elements, measurement of the load carrying ability of the test specimen during the test exposure. 4.3.2 For individual loadbearing members such as beams and columns: 4.3.2.1 Measurement of the load carrying ability under the test exposure with consideration for the end support conditions (that is, restrained or not restrained). 4.4 The test standard does not provide the following: 4.4.1 Information as to performance of test specimens constructed with components or lengths other than those tested. 4.4.2 Evaluation of the degree by which the test specimen contributes to the fire hazard by generation of smoke, toxic gases, or other products of combustion. 4.4.3 Measurement of the degree of control or limitation of the passage of smoke or products of combustion through the test specimen. 4.4.4 Simulation of the fire behavior of joints between building elements such as floor-wall or wall-wall, etc., connections.

Standard Test Methods for Fire Tests of Building Construction and Materials

ASTM E119-16a 建筑结构和材料防火试验的标准试验方法

4.1 These test methods are intended to evaluate the duration for which the types of building elements noted in 1.1 contain a fire, retain their structural integrity, or exhibit both properties during a predetermined test exposure. 4.2 The test exposes a test specimen to a standard fire controlled to achieve specified temperatures throughout a specified time period. When required, the fire exposure is followed by the application of a specified standard fire hose stream applied in accordance with Practice E2226. The test provides a relative measure of the fire-test-response of comparable building elements under these fire exposure conditions. The exposure is not representative of all fire conditions because conditions vary with changes in the amount, nature and distribution of fire loading, ventilation, compartment size and configuration, and heat sink characteristics of the compartment. Variation from the test conditions or test specimen construction, such as size, materials, method of assembly, also affects the fire-test-response. For these reasons, evaluation of the variation is required for application to construction in the field. 4.3 The test standard provides for the following: 4.3.1 For walls, partitions, and floor or roof test specimens: 4.3.1.1 Measurement of the transmission of heat. 4.3.1.2 Measurement of the transmission of hot gases through the test specimen. 4.3.1.3 For loadbearing elements, measurement of the load carrying ability of the test specimen during the test exposure. 4.3.2 For individual loadbearing members such as beams and columns: 4.3.2.1 Measurement of the load carrying ability under the test exposure with consideration for the end support conditions (that is, restrained or not restrained). 4.4 The test standard does not provide the following: 4.4.1 Information as to performance of test specimens constructed with components or lengths other than those tested. 4.4.2 Evaluation of the degree by which the test specimen contributes to the fire hazard by generation of smoke, toxic gases, or other products of combustion. 4.4.3 Measurement of the degree of control or limitation of the passage of smoke or products of combustion through the test specimen. 4.4.4 Simulation of the fire behavior of joints between building elements such as floor-wall or wall-wall, etc., connections.

Standard Test Methods for Fire Tests of Building Construction and Materials

CECS 169-2015 烟雾灭火系统技术规程

本规程适用于新建、改建和扩建的甲、乙、丙类液体固定顶和内浮顶储罐工程中设置的烟雾灭火系统的设计、施工、验收和维护管理。

Technical specification for smoke fire extinguishing systems

DB11/T 1246-2015 城市地下联系隧道防火设计规范

Code for fire protection design of urban underground connecting tunnels

DB11/ 1245-2015 建筑防火涂料（板）工程设计、施工与验收规程

Specifications for engineering design, construction and acceptance of building fireproof coatings (boards)

DIN 4102-16:2015 建筑材料和构件的耐燃性能.第16部分:防火竖井筒检验实施过程

Fire behaviour of building materials and building components - Part 16: "Brandschacht" tests

DIN EN 1991-1-2/NA:2015 国家附录.国家制定参数.欧洲法规1:对建筑物的作用.第1-2部分:一般作用.暴露于火灾中对结构的作用

National Annex - Nationally determined parameters - Eurocode 1: Actions on structures - Part 1-2: General actions - Actions on structures exposed to fire

DB33/T 976-2015 居住出租房消防安全基本要求

Basic requirements for fire safety in residential rental housing