P26 金属结构工程 标准查询与下载
共找到 501 条与 金属结构工程 相关的标准，共 34 页
本文件规定了卧式液压启闭机的型式和系列参数。 本文件适用于水电水利、水运、景观等工程中操作人字闸门、一字闸门、三角闸门、横拉闸门和翻板闸门的卧式液压启闭机。
Horizontal hydraulic hoist series parameters
- ICS
- 27.140
- CCS
- P26
- 发布
- 2022-11-04
- 实施
- 2023-05-04
本规程适用于水电工程闸门、拦污栅和启闭机等设备的运行维护。
Regulations for the operation and maintenance of gates and hoists in hydropower projects
- ICS
- 27.140
- CCS
- P26
- 发布
- 2022-11-04
- 实施
- 2023-05-04
本规范适用于水电工程清污机制造、安装及验收。
Specifications for manufacturing, installation and acceptance of sewage cleaning machines for hydropower projects
- ICS
- 27.140
- CCS
- P26
- 发布
- 2022-11-04
- 实施
- 2023-05-04
本文件规定了水电工程钢闸门的分类和标记，通用技术条件，专用技术条件，试验和验收，标志、包装、运输与存放。 本文件适用于水电工程的平面闸门、弧形闸门、人字闸门和拦污栅，其他类型的钢闸门可参照执行。
Technical conditions for steel gates of hydropower projects
- ICS
- 27.140
- CCS
- P26
- 发布
- 2022-11-04
- 实施
- 2023-05-04
本文件适用于江苏省行政区域内抗震设防烈度为6度至8度的多、高层装配式异形束柱钢结构住宅。
Technical standard for prefabricated special-shaped beam-column steel structure residences
- ICS
- 91.080.10
- CCS
- P26
- 发布
- 2022-03-23
- 实施
- 2022-09-01
本规程适用于多、高层民用建筑中由方钢管混凝土组合异形柱组成的钢框架结构、钢框架-支撑结构、钢框架-延性墙板结构的设计、施工与验收。
Technical specification for prefabricated square steel tube concrete composite special-shaped column structure
- ICS
- 91.080.10
- CCS
- P26
- 发布
- 2021-12-08
- 实施
- 2022-03-01
Acceptance standard for construction quality of cable structure engineering
- ICS
- 91.080.10
- CCS
- P26
- 发布
- 2021-09-27
- 实施
- 2022-01-01
本文件适用于采用里氏硬度法检测并推定工业与民用建筑钢结构工程中型钢（H型钢、工字钢、钢板、槽钢等)抗拉强度的范围，且所测型钢的强度等级不高于Q460级；不适用于经过热处理的钢材强度的测试。
Technical specification for on-site testing of tensile strength of building structural steel by Leeb hardness tester method
- ICS
- 91.080.10
- CCS
- P26
- 发布
- 2021-09-16
- 实施
- 2022-03-01
Technical standard for prefabricated low-rise residential light steel frame-composite wall structure
- ICS
- 91.080.10
- CCS
- P26
- 发布
- 2021-06-21
- 实施
- 2021-10-01
1.总则；2.术语和符号；3.基本规定；4.设计；5.制造；6.安装；7.使用与维护。
Technical specification for thermoformed welded hollow spherical joints
- ICS
- 91.080.10
- CCS
- P26
- 发布
- 2021-05-25
- 实施
- 2021-09-01
This document specifies qualities for high-yield-strength quenched and tempered structural steels. It applies to steel plates and wide flats rolled on a reversing mill which are used in the quenched and tempered condition and normally intended for welded or bolted structures. This document covers 10 grades and 5 qualities. Grades S460Q, S500Q, S550Q, S620Q, S690Q, S890Q and S960Q are covered in Annex A. Grades SG460Q, SG500Q, and SG700Q are covered in Annex B. Not all grades are available in all qualities, and some qualities have Charpy V-notch requirements. The steels specified in this document are applicable to hot-rolled flat products with a minimum nominal thickness of 3 mm and a maximum nominal thickness of 200 mm for grades S460Q, S500Q, S550Q, S620Q and S690Q, a maximum nominal thickness of 125 mm for grades S890Q and S960Q, a maximum nominal thickness of 100 mm for grades SG460Q and SG500Q and a maximum nominal thickness of 150 mm for grade SG700Q. This document does not include the following structural steels, some of which are covered by other International Standards: — Sheet and strip — refer to ISO TC 17/SC 12, Continuous mill flat rolled products; — Tubular products — refer to ISO TC 5/SC 1, Steel tubes. NOTE 1 Lists of standards covered by ISO/TC 17/SC 12 and ISO/TC 5/SC 1 are available on the ISO website. NOTE 2 In all parts of ISO 630, the term of "thickness" is considered as "nominal thickness", unless otherwise stated.
Structural steels - Part 4: Technical delivery conditions for high yield strength quenched and tempered structural steel plates and wide flats
- ICS
- 77.140.01
- CCS
- P26
- 发布
- 2021-04-00
- 实施
This National Annex contains the specific parameter for the use of DIN EN 1999-1-1 in Germany as well as references to additional non-conflicting national rules for the design according to DIN EN 1999-1-1.
National Annex - Nationally determined parameters - Eurocode 9: Design of aluminium structures - Part 1-1: General rules
- ICS
- 91.010.30
- CCS
- P26
- 发布
- 2021-03-00
- 实施
本文件主要技术内容： 1）模型分类与编码：明确装配式建筑钢结构BIM模型的编码应遵循唯一性、稳定性、可扩充性和可传递性的编码原则；明确模型分类要求；明确装配式建筑钢结构BIM模型的编码由“基本信息码”“标准属性码”和“输入型属性码”三段编码组成，三段编码采用“：”分隔。需补充特殊属性信息的构件，可采用“输入型属性码”进行补充。 2）编码构成：明确装配式建筑钢结构BIM模型项目实施阶段名称及编码，装配式建筑钢结构BIM模型结构体系名称及编码，装配式建筑钢结构BIM模型构件小类和细类编码及名称，装配式建筑钢结构BIM模型属性类型及属性参数编码，装配式建筑钢结构BIM模型输入型属性类型编码及属性参数。 3）编码使用与管理：对模型使用要求、编码使用、编码管理做出规定。
Classification and coding of BIM model for prefabricated steel building
- ICS
- 91.080.10
- CCS
- P26
- 发布
- 2021-02-26
- 实施
- 2021-05-01
Safety testing requirements for outdoor advertising and signboard facilities
- ICS
- 91.040.20
- CCS
- P26
- 发布
- 2021-02-09
- 实施
- 2021-05-01
本规程适用于8度和8度以下抗震设防地区，钢结构装配式建筑非承重外墙板工程的设计、施工及验收。
Technical specification for the application of steel structure assembly building exterior wall panels
- ICS
- 91.060.10
- CCS
- P26
- 发布
- 2021-02-04
- 实施
- 2021-06-01
his Part 1-4 of EN 1993 gives supplementary provisions for the design of buildings annd civil engineering works that extend and modify the application of EN 1993-1-1, EN 1993-1-3, EN 1993-1-5 and EN 1993-1-8 to austenitic, austenitic-ferritic and ferritic stainless steels.
Eurocode - Design of steel structures - Part 1-4: General rules - Supplementary rules for stainless steels; German version EN 1993-1-4:2006/A2:2020
- ICS
- 91.010.30
- CCS
- P26
- 发布
- 2021-02-00
- 实施
本文件规定了公称尺寸不大于DN1400不锈钢复合钢制对焊管件的术语和定义、类型、代号与标志、制造和设计、要求、试验方法、检验规则、包装、运输、贮存和产品质量证明书。
Stainless Steel Composite Steel Butt Welding Fittings
- ICS
- 91.100.01
- CCS
- P26
- 发布
- 2021-01-26
- 实施
- 2021-06-01
本文件规定了湿气固化型缓粘结预应力钢绞线的术语和定义，分类、代号和标记，要求，试验方法，检验规则，标志、包装、质量证明书、运输和贮存。
Moisture-curing slow bonded prestressed steel strand
- ICS
- 91.100.01
- CCS
- P26
- 发布
- 2021-01-26
- 实施
- 2021-06-01
Information exchange standard for digital model of steel structure manufacturing
- ICS
- 91.080.10
- CCS
- P26
- 发布
- 2020-11-27
- 实施
- 2021-05-27
Technical specifications for outdoor advertising facilities
- ICS
- 91.080.10
- CCS
- P26
- 发布
- 2020-10-21
- 实施
- 2020-11-21
