Q18 装修材料 标准查询与下载

ASTM D7251-10 杂色塑料壁板产品的颜色和外观保持性的标准规范

1.1 This specification establishes requirements and test methods for the color and appearance retention of variegated color plastic siding products. 1.2 Color retention testing provides a method for estimating the acceptability of color change in a siding product over a period of years of service. 1.3 Characterization of color and appearance for variegated colors is complicated by the presence of multiple colors in a random pattern. The procedure is based on using a template to reference six spots for color measurement. 1.4 Methods of indicating compliance with this specification are provided. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 18212;There is no known ISO equivalent to this standard.

Standard Specification for Color and Appearance Retention of Variegated Color Plastic Siding Products

ASTM D3730-10 高性能内结构墙涂层试验的标准指南

1.1 This guide covers the selection and use of test methods for high-performance interior architectural wall coatings (HIPAC) that differ from more conventional coatings by being tougher, more stain-resistant, more abrasion-resistant and, ordinarily, designed to be applied to wall surfaces of steel, masonry (poured concrete, concrete block, or cinder block), and plaster or gypsum wallboard. The tests that are listed in Table 1 and Table 1 are designed to measure performance properties. These tests may not all be required for each HIPAC system. Selection of the test methods to be followed must be governed by experience and the requirements in each individual case, together with agreement between the purchaser and the seller. 1.2 High-performance architectural coatings are tough, extra-durable organic coating systems that are applied as a continuous (seamless) film and cure to a hard finish. The finish can be high gloss, semigloss, or low gloss as desired. These coatings are resistant to persistent heat, humidity, abrasion, staining, chemicals, and fungus growth. They are used in areas where humidity, wear, or unusual chemical resistance requirements, particularly to soiling, are required and where strong detergents are used to maintain sanitary conditions. Halls and stairways in public buildings, lavatories, stall showers, locker areas, animal pens, and biological laboratories are typical applications. In addition, food processing plants, dairies, restaurants, schools, and transport terminals frequently use HIPAC systems. These are effective in many areas of building interiors compared with tile and are of low materials and maintenance costs. They are used as a complete system only as recommended by the manufacturer since the individual coats in a system are formulated to be compatible with each other. HIPAC systems should be applied only to properly prepared surfaces such as steel or masonry, including cinder blocks and cement blocks. They can be applied over plaster and gypsum wallboard. Ordinarily, a prime or fill coat, if required, is part of the system. 1.3 While they are excellent for walls, HIPAC are not usually intended for ceilings and floors. They would not ordinarily be used in homes, although parents with small children might want to use HIPAC coatings on some walls. 1.4 The types of resin ordinarily used are the following: epoxy-polyamide, two-package; polyester-epoxy, two-package; polyurethane, one-package or two-package. However, other resin types are not excluded provided they can meet the requirements (performance specifications) laid down by the purchaser. 1.5 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For a specific hazard statement, see the note in 7.6.

Standard Guide for Testing High-Performance Interior Architectural Wall Coatings

JC/T 1093-2009 树脂装饰砖

本标准规定了树脂装饰砖的术语和定义、一般要求、试验方法、检验规则、标志、使用说明书、包装、运输及贮存。 本标准适用于建筑物内墙饰面的树脂装饰砖。

Synthetic resin decorative tiles

SANS 630:2009 装潢用的高度光泽瓷漆

Specifies the requirements for two grades of air-drying gloss enamel paints for use on suitably primed and uncoated steel, wood, masonry, hardboard, compressed fibre board, and similar materials used in the construction and finishing of buildings.

Decorative high gloss enamel paints

DB34/ 980-2009 浴室柜

本标准适用于台面材料采用人造板、人造大理石，柜体材料采用人造板的浴室柜系列产品。

Bathroom furniture

BS 1722-16:2009 围墙.用作部件和筛孔的塑料精饰的粉末涂料的规范

This part of BS 1722 specifies performance requirements and describes methods for laboratory testing of powder coatings and the applied powder coatings used as a finish to fence components and mesh. NOTE Annex A gives some guidance on the care and protection of plastics finishes.

Fences - Specification for powder coatings used as a plastics finish to components and mesh

EN 14279:2004+A1:2009 单板层积材（LVL）.定义,分类和规范

This document gives definitions, a classification and specifies the requirements for Laminated Veneer Lumber (LVL) for general purposes or for use in construction in dry, humid or exterior conditions. NOTE This standard will be called up in EN 13986 for construction applications. Annex A "Evaluation of the bonding quality of laminated veneer lumber" is normative Information on supplementary properties is given in Annex B.

Laminated Veneer Lumber (LVL) - Definitions, classification and specifications

ASTM D7514-09 用目测法评定建筑涂料系统墨水片块染色的试验方法

This standard may be used by paint companies and raw material suppliers to assess effectiveness of interior architectural primers for blocking stains from bleeding through to a topcoat. In practice, different ink-stained substrates may give various results for stainblocking performance for a primer and topcoat system. As such, this test method may be used for a number of different ink-stained surfaces.1.1 This standard provides a method for evaluating the ability of an architectural paint system to block ink stains from markers and writing instruments from bleeding through a primer into a topcoat. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Evaluating Ink Stainblocking of Architectural Paint Systems by Visual Assessment

ASTM D7489-09 评价建筑涂料在不同环境条件下的修补性能的标准规程

During construction of a home, paints are subjected to a wide variety of drying conditions, and this may exhibit differences between the original coat and the touched-up area in appearance after its full cure. Therefore, it it essential for the paint to be able to perform under a wide variety of drying conditions. A paint that does this is very advantageous to the contractor. It is possible for a paint to have excellent color touch-up, but poor sheen touch-up, or vice-versa. The ideal paint will have both excellent color and sheen touch-up under testing conditions. Color, gloss and base choice can have a major impact on touch-up of the paint.1.1 This practice determines the ability of a paint to be recoated or “touched up” in small areas. Variations in color, gloss, and sheen that result in a different appearance from the original paint can be evaluated visually. 1.2 This practice describes evaluation of touch-up characteristics in a laboratory-scale controlled environment as opposed to a full-scale field environment. 1.3 Evaluation of touch-up properties under constant drying conditions is described. Environmental conditions can be adjusted to incorporate high or low temperature drying , or both. The changes in application temperature can lead to larger differences in touch-up than applying both coats under the same environmental conditions. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Evaluating Touch-Up Properties of Architectural Coatings under Various Environmental Conditions

KS F 2609-2008 建筑材料吸水系数测定方法

이 표준은 건축 재료의 물 흡수 계수 측정에 대하여 규정한다.

Determination of the water absorption coefficient of building materials

KS F 2605-2008 建筑内部板材耐潮性能试验方法

이 표준은 건축용 내장 보드류1)의 온도ㆍ습도2)가 일정 또는 비교적 고온도에서 온도ㆍ습도

Test methods for moisture resistance of board for interior system of building

KS F 2620-2008 建筑涂料和板材附着层的耐疲劳性试验方法

이 표준은 건축물 등의 보호, 마무리 등의 목적으로 지붕 슬라브, 벽, 바닥 등에 접착하여

Test methods for movement capability of coatings and sheets fully adhered on substrate

KS F 2604-2008 建筑外墙材料抗冻性试验方法(冻融法)

이 표준은 건축물에 사용하는 외벽 재료의 내동해성 시험방법(동결 융해법)에 대하여 규정한다

Test methods for frost resistance of exterior wall materials of buildings(freezing and thawing method)

JIS L 4406 AMD 1:2008 瓷砖铺面(修改件1)

この規格は，タフテッドカーべットのタィルカーペット()の要求事項について規定する。

Tile carpet(Amendment 1)

DIN CEN/TS 15717:2008 镶木地板.安装用通用指南

Parquet flooring - General guideline for installation; German version CEN/TS 15717:2008

JC/T 864-2008 聚合物乳液建筑防水涂料

本标准规定了聚合物乳液建筑防水涂料的分类与标记、要求、试验方法、检验规则、包装、标志、运输与贮存。 本标准适用于各类以聚合物乳液为主要原料，加入其他添加剂而制得的单组分水乳型防水涂料。本标准适用的产品可在非长期浸水环境下的建筑防水工程中使用。若用于地下及其他建筑防水工程，其技术性能还应符合相关技术规程的规定。

Polymer emulsion architectural waterproof coating

NF P61-549:2008 用于瓷砖下部、胶粘剂粘合的防水渗透的液体 要求、试验方法、合格性评定、分类和名称

Liquid applied water impermeable products for use beneath ceramic tiling bonded with adhesives - Requirements, test methods, evaluation of conformity, classification and designation.

DIN EN 14041:2008 弹性织物和层压地板覆盖物.基本特性

This document specifies the health, safety and energy saving requirements for: ~ resilient floor coverings manufactured from plastics, linoleum, cork or rubber, excluding loose-laid mats; ~ textile floor coverings, excluding loose-laid mats and rugs; ~ laminate floor coverings; ~ floor panels for loose-laying. It also specifies procedures for testing for the evaluation of conformity of the products and the requirements for marking and labelling. The products are intended for use as floor coverings within a building or externally, according to the manufacturer's specifications. This document does not apply to floor coverings containing asbestos. This document does not specify requirements unrelated to health, safety and energy saving, which are covered in the separate European Standards for these products, listed in Annex A. To perform correctly, products covered by this standard require correct installation and maintenance. This document does not, however, cover installation or maintenance, but does give advice on minimising slip hazards.

Resilient, textile and laminate floor coverings - Essential characteristics(includes Corrigenda AC:2005+AC:2006); English version of DIN EN 14041:2008-05

SANS 1763:2008 装饰用三聚氰胺贴面板

Specifies the requirements for decorative aminoplast-faced boards, which are referred to as decorative melamine-faced boards (MFB) or low-pressure laminates and are used, for example, for furniture and interior work.

Decorative melamine-faced boards

ISO 19712-1:2008 塑料.固体表面的装饰材料.第1部分:分类和规范

This part of ISO 19712 establishes a classification system for solid surfacing materials according to their performance. This part of ISO 19712 also specifies property requirements for the various types of solid surfacing materials covered by this classification. Requirements are specified for the types that are most generally used, but additional types may be added as required. The specified limit values apply to the most commonly used types of material, but within each classification it may be possible to obtain variants having much higher performance values. These materials are characterized by their homogeneous appearance, renewable surfaces and inconspicuous seams. They are generally classified as follows. a) Solid surface sheets Solid surfacing sheets are designed for horizontal, vertical, wet and dry applications. b) Solid surface shapes Solid surface shapes include, but are not limited to, kitchen sinks, bathroom sinks, vanity tops, showers, tubs and spas. The important properties of solid surfacing materials are - water resistance, - thermal shock resistance, - heat resistance, - impact resistance, - stain and chemical resistance, - cigarette burn resistance, - colour stability, - hardness, - bacterial and fungal resistance, - cleanability, - hygiene, - seamability, - renewability.

Plastics - Decorative solid surfacing materials - Part 1: Classification and specifications