Q18 装修材料 标准查询与下载

JIS A 1437 AMD 1:2008 建筑物内部系统用板材耐湿性的试验方法(修改件1)

This standard specifies an Amendment of Test methods for moisture resistance of boards for interior system of building .

Test methods for moisture resistance of boards for interior system of building (Amendment 1)

GME TM 294000-2008 内饰织物（绞接）

Upholstery Fabric Splice

GME TM 209600-2008 内饰织物（编织）

Upholstery Fabric

Upholstery Fabric Twist

JC/T 1074-2008 室内空气净化功能涂覆材料净化性能

本标准规定了室内空气净化功能涂覆材料的术语和定义、产品分类与标记、要求、试验方法、试验报告、检验规则。 本标准适用于具有空气净化功能的室内装饰、装修涂覆材料及喷涂材料。具有空气交货功能的壁纸、天花板等装饰材料可参照本标准。

Purificatory performance of coatings with air Purification

DIN EN 15102:2008 装饰墙面涂层.辊子和板条形产品

This European Standard applies to all forms of wallcovering products in roll and panel form as defined in EN 235 supplied for hanging onto internal walls, partitions or ceilings, by means of an adhesive, whose primary purpose is decorative. However, certain wallcovering products may confer minor sound absorbtion and thermal resistance properties. It also provides for the evaluation of conformity of products to the requirements of this standard. It does not apply to wall coverings whose primary purpose is structural or protective (e.g. vapour or moisture barriers).

Decorative wallcoverings - Roll and panel form products; English version of DIN EN 15102:2008-01

ASTM D7394-08 用立体台式旋转粘度计测定建筑涂料流变学性能的规程

A significant feature of this practice is the ability to obtain a semblance of coating rheology over a broad range of shear rates with the same bench viscometers and test protocol that paint formulators and paint QC analysts routinely use. By using this procedure, an approximation of the shear rheology of a coating is possible without using a rheometer, and performance predictions can be made based on those measurements. Low-Shear Viscosity (LSV)8212;The determination of low-shear viscosity in this practice can be used to predict the relative “in-can” performance of coatings for their ability to suspend pigment or prevent syneresis, or both. The LSV can also predict relative performance for leveling and sag resistance after application by roll, brush or spray. Fig. 1 shows the predictive low-shear viscosity relationships for several coatings properties. 5.3 Mid-Shear Viscosity (MSV)8212;The determination of MSV (coating consistency) in this practice is often the first viscosity obtained. This viscosity reflects the coatings resistance to flow on mixing, pouring, pumping, or hand stirring. Architectural coatings nearly always have a target specification for mid-shear viscosity, which is usually obtained by adjusting the level of thickener in the coating. Consequently, mid-shear viscosity is ideally a constant for a given series of coatings being tested to provide meaningful comparisons of low-shear and high-shear viscosity. With viscosities at the same KU value, MSV can also be used to obtain the relative Mid-Shear Thickener Efficiency (MSTE) of different thickeners in the same coating expressed as lb thickener/100 gal wet coating or g thickener/L wet coating. 5.4 High-Shear Viscosity (HSV)8212;High-shear viscosity in this practice is a measure of the coatings resistance to flow on application by brush or roller, which is often referred to as brush-drag or rolling resistance respectively. This viscosity relates to the coatings ability to provide one-coat hiding, its ease of application (brushing or rolling resistance), and its spread rate. Fig. 2 shows high-shear viscosity relationship predictions for relative coating performance. FIG. 1 Low Shear Viscosity (LSV) FIG. 2 High Shear Viscosity (HSV)1.1 This practice covers a popular industry protocol for the rheological characterization of waterborne architectural coatings using three commonly used rotational bench viscometers. Each viscometer operates in a different shear rate regime for determination of coating viscosity at low shear rate, mid shear rate, and at high shear rate respectively as defined herein. General guidelines are provided for predicting some coating performance properties from the viscosity measurements made. With appropriate correlations and subsequent modification of the performance guidelines, this practice has potential for characterization of other types of aqueous and non-aqueous coatings. 1.2 The values stated in SI units are to be regarded as standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Rheological Characterization of Architectural Coatings using Three Rotational Bench Viscometers

HJ/T 414-2007 环境标志产品技术要求 室内装饰装修用溶剂型木器涂料

本标准规定了室内装饰装修用溶剂型木器涂料环境标志产品的术语和定义、基本要求、技术内容和检验方法。 本标准适用于室内装饰装修用的硝基类、聚氨酯类、醇酸类溶剂型面漆和底漆。不适用于辐射固化类涂料。

Technical requirement for enviromnental labeing products Solvent-based wood coatings for indoor decoration and refurbishing

JG/T 229-2007 外墙外保温柔性耐水腻子

本标准规定了外墙外保温柔性耐水腻子的术语和定义、要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于以水泥、聚合物粉末、合成树脂乳液或其他材料为主要粘结剂，配以填料、助剂等制成的建筑外墙外保温抹面层找平及防裂用柔性耐水腻子。

Waterproofing flexible putty for exterior thermal insulation systems

BS EN 15102:2007 装饰墙面涂层.辊子和面板形产品

This European Standard applies to all forms of wallcovering products in roll and panel form as defined in EN 235 supplied for hanging onto internal walls, partitions or ceilings, by means of an adhesive, whose primary purpose is decorative. However, certain wallcovering products may confer minor sound absorbtion and thermal resistance properties. It also provides for the evaluation of conformity of products to the requirements of this standard. It does not apply to wall coverings whose primary purpose is structural or protective (e.g. vapour or moisture barriers).

Decorative wallcoverings - Roll and panel form products

BS EN 15102:2007+A1:2011 装饰墙面涂层.辊子和面板形产品

Decorative wall coverings. Roll and panel form

KS F 2607-2007 建筑材料透湿度试验方法

이 규격은 주로 건축물에 사용하는 재료의 투습성 측정 방법에 대하여 규정한다.

Measuring method of water vapour permeability for building materials

KS F 2610-2007 建筑材料的二氧化碳渗透性测试方法

이 규격은 주로 건축물에 사용하는 마감 재료의 이산화탄소 투과성 측정 방법에 대하여 규정한

Measuring method of carbon dioxide permeability for building materials

EN 15468:2007 层压地板覆盖物.直接应用印刷物和树脂表面层的元素.规范,要求和测试方法

Laminate floor coverings - Elements with directly applied printing and resin surface layer - Specifications, requirements and test methods

JC/T 1059-2007 金属及金属复合材料吊顶板

本标准规定了金属及金属复合材料吊顶板（以下称吊顶板）的产品术语和定义、分类代号及标记、原材料要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存及随行文件。 本标准适用于建筑装饰、装修用金属及金属复合材料吊顶板。

Metal and metal-composite ceilings

JC/T 443-2007 纸面石膏板护面纸板

本标准规定了纸面石膏板（以下简称护面纸板）的技术要求。 本标准适用于纸面石膏板及其深加工的各类产品的护面纸板。

Paper for gypsum board

JG/T 224-2007 建筑用钢结构防腐涂料

本标准规定了建筑用钢结构防腐涂料的分类技术指标、试验方法、检验规则及标志包装、运输、贮存等要求。 本标准适用于在大气环境下建筑钢结构防护用底漆、中间漆和面漆，也适用于大气环境下其他钢结构防护用底漆、中间漆和面漆。

Anticorrosive coatings for building steel structure

JC/T 1040-2007 建筑外表面用热反射隔热涂料

本标准规定了建筑外表面用热反射隔热涂料的术语和定义、分类和标记、要求、试验方法、检验规则及标志、包装、运输和贮存等要求。 本标准适用于通过反射太阳热辐射来减少建筑物和构筑物热荷载的隔热装饰涂料。产品主要由合成树脂、功能性颜填料及各种助剂配制而成。

Exterior reflective thermal insulating coatings on buildings

JIS A 1445:2007 天花板悬浮系统用材料的测试方法

この規格は，主として事務室及び店舗に使用するシステム天井構成部材のうち,Tバー,Hバー, Tハンガ，CTハンガ，CHクリップ，T バー継手金物及びTバークロス接合金物の試験方法について規定する。ただし,Tバーにかかる荷重は，おおむね110 N/m以下のものとし，それを超えるものは除く。

Testing methods of materials for ceiling suspension system

JIS A 6916 ERRATUM 1:2007 勘误表

ERRATUM

JG/T 210-2007 建筑内外墙用底漆

本标准规定了建筑内外墙用底漆的术语、分类和标记、要求、试验方法、检验规则及标志、包装和贮存等。 本标准适用于以合成树脂乳液、溶剂型树脂或其他材料为主要粘结剂，配以助剂、颜填料等制成的建筑内外墙用各类底漆。

Primer for interior and exterior wall