Q21 石材制品 标准查询与下载

JC/T 1049-2007 超薄天然石材型复合板

本标准规定了超薄天然石材型复合板（以下简称复合板）的定义、产品分类、技术要求、试验方法、检验规则、标志、包装、运输与贮存等。 本标准适用于建筑装饰用超薄天然石材型复合板。

Complex veneer super thin stone

DIN EN 1926:2007 天然石料试验方法.单轴抗压强度的测定

This European Standard specifies a method for determining the uniaxial compressive strength of natural stones.

Natural stone test methods - Determination of uniaxial compressive strength; English version of DIN EN 1926:2007-03

SANS 927:2007 预制混凝土路边石，边缘和渠道

Specifies the dimensional and physical requirements for various types of precast concrete kerbs, edgings and channels intended for use in the construction of roads and footpaths.

Precast concrete kerbs, edgings and channels

DIN EN 1936:2007 天然石料检验方法.测定实际和表观密度以及总开放式孔隙率

This European Standard specifies methods for determining the real density, apparent density, and open and total porosity of natural stone.

Natural stone test method - Determination of real density and apparent density, and of total and open porosity; English version of DIN EN 1936:2007-02

DIN EN 12372:2007 天然石料检验方法.集中负荷抗弯强度测定

This European Standard specifies a test method for determination of flexural strength under a concentrated load for natural stone. Both an identification and a technological product testing procedure are included.

Natural stone test methods - Determination of flexural strength under concentrated load; English version of DIN EN 12372:2007-02

BS EN 1926:2006 天然石料试验方法.单轴抗压强度的测定

This European standard specifies a method for determining the uniaxial compressive strength of natural stones.

Natural stone test methods — Determination of uniaxial compressive strength

BS EN 1936:2006 天然石料试验方法.实际和表观密度及总孔率和开孔率的测定

This European standard specifies methods for determining the real density, apparent density, and open and total porosity of natural stone.

Natural stone test methods — Determination of real density and apparent density, and of total and open porosity

ASTM C119-07a 与规格石料相关的标准术语

Standard Terminology Relating to Dimension Stone

EN 1936:2006 天然石料测验方法.实密度和表观密度及总孔隙度和开孔率的测定

La présente Norme européenne spécifie des méthodes de détermination des masses volumiques réelle et apparente ainsi que des porosités ouverte et totale de la pierre naturelle.

Natural stone test methods - Determination of real density and apparent density, and of total and open porosity

SANS 6245:2006 含碱性石料潜在活性（快速砂浆棱镜法）

Specifies a method for predicting the potential reactivity of an aggregate with alkalis, as may be the case in practice if the aggregate is used in conjunction with cement of high alkali content.

Potential reactivity of aggregates with alkalis (accelerated mortar prism method)

SANS 6246:2006 石料的Treton冲击强度值

Specifies a method for determining the Treton value, which is a measure of the resistance of aggregate to impact. The aggregate is subjected to the blows of a falling hammer and the resulting disintegration is measured by means of the quantity that pass

Treton impact value of aggregates

BS EN 14617-13:2005 人造合成石.试验方法.第13部分:电阻率测定

This test method covers the determination of dc insulation resistance, volume resistance and resistivity, as well as surface resistance and resistivity, and the corresponding electrical conductance and conductivity, of specimens of agglomerated stone products conforming to the definition reported in EN 14618. These products are usually made by stone aggregates bound via either resin and filler or cement and water (paste components) or a mixture of polymer/cement and related addition (such as reinforcing fibres, electrically insulating/conducting fillers, etc.). Resistivity/conductivity may be also used as an indirect measure of some properties of agglomerated stones products (see Annex A).

Agglomerated stone - Test methods - Part 13: Determination of electrical resistivity

DD CEN/TS 772-22:2006 砌体砌块试验方法第22部分：粘土砌块抗冻融能力的测定

This Technical Specification specifies a method for determining the freeze/thaw resistance of clay masonry units that are declared by the manufacturer as meeting the requirements for HD units and as suitable to be subjected to severe (F2) exposure.

Methods of test for masonry units — Part 22: Determination of freeze/thaw resistance of clay masonry units

DIN 52008:2006 天然石料试验方法.耐气候老化的评估

The document specifies the main test methods for the assessment of the weathering resistance of natural stone.

Natural stone test methods - Assessment of the weathering resistance

ASTM D5121-06 预制岩石板层耐久性试验的标准实施规程

This practice is used to prepare specimens to evaluate any internal defects, such as cracks, that may not be apparent on the surfaces of broken blocks of rock. Such evaluation can also aid in the selection and location of slabs for testing as outlined in Practice D 4992. In some cases, the need for further testing or evaluation may be eliminated. The sawing of rock samples will reduce them to a suitable size for testing and, in many cases, preserve the natural structure of the internal defects so the samples can be evaluated by the various durability tests. Durability tests specimens should be 64 ± 6 mm 2.5± 0.25 in) thick normal to bedding or any potential planes of weakness which may be observed in the samples. In no case will the size of the slab be less than 125 mm (5 in.) on a side, excluding the thickness Ideally, a test specimen size equal to the proposed design size would provide the ultimate in correlation between laboratory tests and actual field performance. However, in most cases, this is neither practical nor economically feasible.1.1 This practice covers the preparation of rock slabs for various tests used to evaluate any visual internal defects, or the durability of rock by means of laboratory tests. These tests include, but are not limited to, Test Methods D 5240, D 5312, and D 5313. 1.2 Units The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only.1.3 All observed and measured values shall conform to the guidelines for significant digits and rounding established in Practice D 6026.1.4 This practice offers a set of instructions for performing one or more specific operations. This document cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this practice may be applicable in all circumstances. This ASTM standard is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this document be applied without consideration of a project''s many unique aspects. The word "Standard" in the title of this document means only that the document has been approved through the ASTM consensus process. This standard does not purport to address all of the safety concerns associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For a specific hazards statement, see Section 7.

Standard Practice for Preparation of Rock Slabs for Durability Testing

ASTM C880-06 规格石料弯曲强度的标准试验方法

This test method is useful in indicating the differences in flexural strength between the various dimension stones. This test method also provides one element in comparing stones of the same type. 1.1 This test method covers the procedure for determining the flexural strength of stone by use of a simple beam using quarter-point loading. 1.2 Stone tests shall be made when pertinent for the situation when the load is perpendicular to the bedding plane and when the load is parallel to the bedding plane. 1.3 As required, the flexural tests shall also be conducted under wet conditions. 1.4 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Flexural Strength of Dimension Stone

ASME A112.19.16-2006 水磨石卫生设备

This Standard establishes the minimum requirements for terrazzo materials that are used to manufacture plumbing fixtures for general use. It includes material, structural and physical test requirements, and marking and identification of fixtures complying with this Standard. The provisions of this Standard are not intended to prevent the use of any alternate design that meets or exceeds the intent of this Standard.

Terrazzo Plumbing Fixtures

ASTM C119-06 与规格石料相关的标准术语

Standard Terminology Relating to Dimension Stone

ASTM C170-06 规格石料的耐压强度用标准试验方法

This test method is useful in indicating the differences in compressive strength between the various dimension stones. This test method also provides one element in comparing stones of the same type.1.1 This test method covers the sampling, preparation of specimens, and determination of the compressive strength of dimension stone.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Compressive Strength of Dimension Stone

ASTM C1364-06 建筑用铸石的标准规范

1.1 This specification covers the physical requirements, sampling, testing, and visual inspection of architectural cast stone.1.2 Units covered by this specification may be made from facing and backup mixtures or from a homogeneous mixture. Either wet cast or dry cast production methods may be used.1.3 Surface textures, finish, color, or other special features should be specified separately by the purchaser.1.4 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Architectural Cast Stone