Q21 石材制品 标准查询与下载

ASTM C1527/C1527M-11 石灰石规格料标准规格

1.1 This specification covers the material characteristics, physical requirements, and sampling appropriate to the selection of travertine for general building and structural purposes. Refer to Guides C1242 and C1528 for the appropriate selection and use of travertine dimension stone. 1.2 Dimension travertine shall include stone that is sawed, cut, split, or otherwise finished or shaped and shall specifically exclude molded, cast, or otherwise artificially aggregated units composed of fragments, and also crushed and broken stone. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

Standard Specification for Travertine Dimension Stone

ASTM C1515-11 新建或已建外部规格石块垂直及水平的表面清洁的标准指南

Exterior dimension stone is chosen for use in contemporary architecture in part because of its aesthetic appeal. Aesthetics can be significantly diminished when dirt, grime, fly ash, algae and other contaminants collect on the surface of stone. This guide is intended to assist those who wish to preserve the original appearance of a new structure or to return a stone-clad building to its original color and appearance. Note that cleaning may not be able to return discolored or faded stone to its original appearance. This guide may be used as a construction document.1.1 This guide describes materials and procedures which may be used to clean dimension stone exteriors as well as the conditions under which they may be used. It is intended to aid owners, maintenance supervisors and building managers, architects and engineers, and contractors in cleaning vertical exterior dimension stone on commercial, residential and institutional structures. This guide may also be helpful to those who wish to clean stone masonry on bridges, retaining walls, ramps, and plazas, and free-standing stone objects such as statuary, memorials and grave markers. 1.2 This guide relates primarily, to routine maintenance of the surface finish of exterior dimension stone. The techniques noted herein may not be appropriate or cost effective with regard to restoration of disfigured, severely soiled or stained stonework, or of stonework of particular historic importance. In cases where staining occurs on surfaces which have cultural, civic, historic or architectural significance, consultation with a specialist is recommended. 1.3 The user of this guide should also obtain and have on file at both the job site and the office Material Safety Data Sheets (MSDS) describing the nature of all chemical products utilized during the cleaning process. 1.4 A file of literature from the manufacturers of all products involved within the scope of each project should be available for reference. 1.5 These procedures are not intended for interior stonework. 1.6 This guide offers an organized collection of information or a series of options and does not recommend a specific course of action. This document cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this guide may be applicable in all circumstances. This ASTM standard is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this document be applied without consideration of a project’s many unique aspects. The word “Standard” in the title of this document means only that the document has been approved through the ASTM consensus process. 1.7 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

Standard Guide for Cleaning of Exterior Dimension Stone, Vertical And Horizontal Surfaces, New or Existing

DB21/T 1837-2010 蒸压粉煤灰砖建筑技术规程

Technical specification for autoclaved fly ash brick construction

DIN EN 12371:2010 天然石料试验方法. 抗冻性测定; 德文版本EN 12371: 2010

Natural stone test methods - Determination of frost resistance; German version EN 12371:2010

BS EN 12371:2010 天然石料试验方法.抗冻性测定

This European Standard specifies a method to assess the effect of freeze/thaw cycles on natural stones (see EN 12670 for terminology, and EN 12440 for denomination). The standard contains provision for both a shorter technological test (Test A) to assess the effect of freeze/thaw cycles on the relevant performance characteristics and an identification test (Test B).

Natural stone test methods - Determination of frost resistance

DB44/T 768-2010 树脂型人造石板材

本标准规定了树脂型人造石板材（以下简称“板材”）的术语与定义、分类与等级、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于以树脂或高分子聚合物为粘合剂加工而成的建筑装饰用人造石板材，不适用于以水泥或树脂水泥两者混合物为粘合剂加工而成的人造石板材。

Resin type artificial stone plate

DB13/T 753-2010 石材雕刻（圆雕）产品技术规范

Technical specifications for stone carving (round carving) products

ASTM C1528-10 室外用规格石料选择的标准指南

Related Components8212;Natural stone is only one component of a building's construction. All related materials and assemblies need to be evaluated to ensure compatible interactive behavior with the stone product. Applicable Codes8212;Every stone application shall comply with applicable building codes.1.1 This guide is intended to be used by architects, engineers, specifiers, contractors, and material suppliers who design, select, specify, install, purchase, fabricate, or supply natural stone products for construction applications. 1.2 Consensus Standard8212;This guide is an industry consensus standard drafted in a cooperative effort among engineers, architects, geologists, producers, and installers of natural stone.

Standard Guide for Selection of Dimension Stone

ASTM C615/C615M-10 花岗岩规格料标准规格

1.1 This specification covers the material characteristics, physical requirements, and sampling appropriate to the selection of granite for general building and structural purposes. 1.2 Granite dimension stone shall include stone that is sawed, cut, split, or otherwise finished or shaped, and shall specifically exclude molded, cast, or otherwise artificially aggregated units composed of fragments, crushed and broken stone. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

Standard Specification for Granite Dimension Stone

ASTM C503/C503M-10 大理石规格料的标准规格

1.1 This specification covers the material characteristics, physical requirements, and sampling appropriate to the selection of marble for general building and structural purposes. Refer to Guides C1242 and C1528 for the appropriate selection and use of marble dimension stone. 1.2 Dimension marble shall include stone that is sawed, cut, split, or otherwise finished or shaped into blocks, slabs or tiles, and shall specifically exclude molded, cast and artificially aggregated units composed of fragments, and also crushed and broken stone. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

Standard Specification for Marble Dimension Stone

ASTM C1364-10b 建筑铸石标准规范

1.1 This specification includes the physical properties, sampling, testing, tolerance, and appearance requirements for architectural cast stone. 1.2 Cast stone units covered under this specification include both wet cast and vibratory dry tamp products. Production methods of cast stone can vary among manufacturers; many production methods are acceptable provided the delivered cast stone meets the requirements of this specification. 1.3 Surface textures, finish, color, special applications, or other features shall be specified by the purchaser. Slump, manufacturing method, and apparatus shall be selected by the manufacturer and not specified by the purchaser. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Architectural Cast Stone

ASTM C1527/C1527M-10 石灰华规格石料标准规范

1.1 This specification covers the material characteristics, physical requirements, and sampling appropriate to the selection of travertine for general building and structural purposes. 1.2 Dimension travertine shall include stone that is sawed, cut, split, or otherwise finished or shaped and shall specifically exclude molded, cast, or otherwise artificially aggregated units composed of fragments, and also crushed and broken stone. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

Standard Specification for Travertine Dimension Stone

ASTM D7625-10 使用CERCHAR法在实验室内测定石材的磨蚀性的标准试验方法

The CERCHAR test and associated CAI were developed at a time of more demand for application of mechanical excavation machines at the Laboratoire du Center d' ?/span>tudes et Recherches des Charbonnages de France (CERCHAR) (3). CAI is used to assess the abrasiveness of rock for mechanical excavation. Rock abrasiveness governs the performance of disc cutters, the rate of its replacement and therefore subsequent tunnel costs. Advances in methods of underground excavation, in particular the use of the tunnel boring machine (TBM), necessitates knowledge of rock abrasiveness. Abrasiveness expresses a behavioral characteristic of rock rather than a fundamental physical or mechanical property. CAI tests were originally carried out on natural broken surfaces. In heterogeneous rock types such as conglomerates, coarse grained granite or schistose rock, suitable fresh test surfaces are not achieved by mechanical breakage using a hammer. In these cases CAI values for “smooth” surfaces cut with a diamond saw are acceptable for use but shall be normalized by Eq 2 before they can be used (1). The test velocity for the Original Cerchar apparatus is approximately 10 mm/s and 1 mm/s for the West Cerchar apparatus. The CAI values obtained for both testing velocities (1) are estimated to be equal. Note 18212;The quality of the result produced by these practices is dependent upon the competence of the personnel performing it and the suitability of the equipment and facilities used. Agencies that meet the criteria of Practice D3740 are generally considered capable of competent and objective testing and sampling. Users of these practices are cautioned that compliance with Practice D3740 does not in itself assure reliable results. Reliable results depend on many factors; Practice D3740 provides a means of evaluating some of those factors.1.1 This test method covers the determination of the abrasiveness of rock by the CERCHAR Abrasiveness Index (CAI) method. The test method consists of measuring the wear on the tip of steel stylus with a cone shape and known Rockwell Hardness, caused by scratching against a freshly broken or saw cut rock surface for a prescribed 10 mm distance using one of the two test apparatus. 1.2 This test method is intended for freshly broken rock surfaces; however, saw cut surfaces are covered for when a satisfactory rock surface cannot be obtained. 1.3 Stylus Rockwell Hardness (HRC) can have a profound effect on the results and the focus of this test method is an HRC value of 55 for every test (1,2). However, there are situations where stylus with different Rockwell Hardness can be used Therefore, this test method includes discussions on stylus with different Rockwell Hardness. 1.4 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026. 1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health prac......

Standard Test Method for Laboratory Determination of Abrasiveness of Rock Using the CERCHAR Method

ASTM C629/C629M-10 板岩规格料标准规格

1.1 This specification covers the material characteristics, physical requirements, and sampling appropriate to the selection of slate for general building and structural purposes. Refer to Guides C1242 and C1528 for the appropriate selection and use of slate dimension stone. 1.2 Dimension slate shall include stone that is sawed, cut, split, or otherwise finished or shaped, and shall specifically exclude molded, cast, or otherwise artificially aggregated units composed of fragments, and also crushed and broken stone. 1.3 It specifically excludes roofing slate (see Specification ) and slate for industrial uses. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

Standard Specification for Slate Dimension Stone

ASTM C616/C616M-10 砂岩规格料标准规格

1.1 This specification covers the material characteristics, physical requirements, and sampling appropriate to the selection of quartz-based dimension stone for general building and structural purposes. Refer to Guides C1242 and C1528 for the appropriate selection and use of quartz-based dimension stone. 1.2 Quartz-based dimension stone shall include stone that is sawed, cut, split, or otherwise finished or shaped, and shall specifically exclude molded, cast, or otherwise artificially aggregated units composed of fragments, and also crushed and broken stone. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

Standard Specification for Quartz-Based Dimension Stone

ASTM C568/C568M-10 石灰石规格石料的标准规格

1.1 This specification covers the material characteristics, physical requirements, and sampling appropriate to the selection of limestone for general building and structural purposes. Refer to Guides C1242 and C1528 for the appropriate selection and use of limestone dimension stone. 1.2 Dimension limestone shall include stone that is sawed, cut, split, or otherwise finished or shaped and shall specifically exclude molded, cast, or otherwise artificially aggregated units of composed fragments, and also crushed and broken stone. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

Standard Specification for Limestone Dimension Stone

ASTM D5121-10 岩石板进行耐久性试验前的处理的标准实施规程

This practice is used to prepare rock specimens for durability testing and to evaluate any internal defects, such as cracks, that may not be apparent on the surfaces of broken blocks of rock. Such evaluation can also aid in the selection and location of slabs for testing as outlined in Practice D4992. In some cases, the need for further testing or evaluation may be eliminated. The sawing of rock samples will reduce them to a suitable specimen size and quantity for testing and, in many cases, preserve the natural structure of the internal defects so the samples can be evaluated by the various durability tests. Durability tests specimens should be 64 ± 6 mm (2.5 ± 0.25 in) thick normal to bedding or any potential planes of weakness which may be observed in the samples. In no case will the size of the slab be less than 125 mm (5 in.) on a side, excluding the thickness Ideally, a test specimen size equal to the proposed design size would provide the ultimate in correlation between laboratory tests and actual field performance. However, in most cases, this is neither practical nor economically feasible.1.1 This practice covers the preparation of rock slabs for various tests and any visual inspections used to evaluate the durability of rock for erosion control. These tests include, but are not limited to, Test Methods D5240, D5312, and D5313. 1.2 Units8212;The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard. 1.3 All observed and measured values shall conform to the guidelines for significant digits and rounding established in Practice D6026. 1.4 This practice offers a set of instructions for performing one or more specific operations. This document cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this practice may be applicable in all circumstances. This ASTM standard is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this document be applied without consideration of a project's many unique aspects. The word “Standard” in the title of this document means only that the document has been approved through the ASTM consensus process. 1.5 This standard does not purport to address all of the safety concerns associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For a specific hazards statement, see Section 7.

Standard Practice for Preparation of Rock Slabs for Durability Testing

KS F 2534-2009 结构混凝土用轻石料

이 표준은 콘크리트의 경량성과 압축강도를 고려하여야 하는 구조용 경량 콘크리트 골재와 콘크

Lightweight aggregate for structural concrete

NF B10-600*NF EN 14618:2009 人造合成石.术语和分级

Agglomerated stone - Terminology and classification.

DIN EN 14618:2009 人造合成石.术语和分级,DIN EN 14618:2009-10的英文版本

This document specifies the terminology and classification of the agglomerated stone products. Agglomerated stone products are industrial products mainly made of hydraulic cement, resin or mixture of both, stones and other additions. They are industrially manufactured in geometrical shapes at fixed plants by moulding techniques. They are put on the market in the form of rough blocks, rough slabs, slabs, tiles, dimensional stone works, and any other cut to size products. All other agglomerated stones products not intended to be used for flooring, wall finishes and similar uses (like drainage channels, structural elements, etc.) are excluded from the field of this standard. This European Standard is not applicable to terrazzo tiles covered by EN 13748-1 [1] and EN 13748-2 [2].

Agglomerated stone - Terminology and classification; English version of DIN EN 14618:2009-10