Q34 工业技术玻璃 标准查询与下载

JC/T 2131-2012 吸油烟机用钢化玻璃

本标准规定了吸油烟机用钢化玻璃的术语和定义、分类、材料、要求、试验方法、检验规则以及标志、包装、运输和贮存等。 本标准适用于家用吸油烟机用钢化玻璃，其中对吸油烟机用釉面钢化玻璃的要求仅适用于采用高温釉的吸油烟机用钢化玻璃。

Tempered glass used on range hoods

JC/T 2130-2012 移动电子产品视屏盖板玻璃

本标准规定了移动电子产品视频盖板玻璃的术语和定义、分类、要求、试验方法、检验规则以及标志、包装、运输和贮存等。 本标准适用于移动电子产品上对显示屏起保护作用的盖板玻璃。

Cover glass for windows of mobile electronic devices

KS L ISO 383:2012 实验室玻璃器皿.互换性锥形磨接口

이 표준은 호환성 코니컬 갈아 맞춤 이음부의 호환성을 확보하기 위하여 치수 및 표면 거칠기

Laboratory glassware-Interchangeable connical ground joints

ASTM E2649-12 用火花源发射光谱法测定密封绝缘玻璃组件中氩浓度的标准试验方法

This test method is intended to provide a means for determining the concentration of argon in sealed insulating glass units under controlled conditions in compliance with the apparatus manufacturer's instructions. This is a non-destructive test method in that the edge seal of the test specimen is not breached in order to determine the argon gas concentration. However, damage to some glass coatings on the inner surfaces of the glass can occur. This test method has been developed based on data collected in a controlled laboratory environment. The device shall be used to determine the argon gas concentration in insulating glass units in a controlled laboratory environment. Refer to 12.3. This test method may be used to determine the argon gas concentration before, during, or after the insulating glass unit is subjected to durability tests. The accuracy of the test method is dependent upon the accuracy of the Spark Emission Spectroscope. When the concentration of the argon being measured is below certain levels, this test method is not applicable. See the spectroscope manufacturer’s literature for recommended levels of accuracy of a given model.1.1 This test method covers procedures for using a spark emission spectroscope to determine the concentration of argon gas in the space between the lites of a sealed insulating glass unit. 1.2 This is a non-destructive test method. 1.3 This test method shall be used only in a controlled laboratory environment. 1.4 This test method is applicable for insulating glass units where argon has been added to the sealed insulating glass cavity and the balance of the gas is atmospheric air. 1.5 This test method is applicable for clear, double-glazed insulating glass units. 1.6 This test method is applicable for double-glazed insulating glass units with one lite having a metallic coating or tinted glass, or both, and with clear glass as the other lite. 1.7 This test method is applicable for triple-glazed insulating glass units only when the center lite of glass has a metallic coating (either low emissivity (low E) or reflective) and both of the other lites are clear glass. 1.8 This test method also includes a procedure for verifying the accuracy of the readings of the test apparatus. 1.9 The values stated in SI units are to be regarded as the standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard. 1.10 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, refer to 7.1.

Standard Test Method for Determining Argon Concentration in Sealed Insulating Glass Units Using Spark Emission Spectroscopy

ASTM E2141-12 评定密封绝缘玻璃件上吸收性电变色涂层的标准试验方法

1.1 These test methods cover the accelerated aging and monitoring of the time-dependent performance of electrochromic glazings. Cross sections of typical electrochromic windows are shown in which devices have four or five-layers of coatings that include the two or three active layers sandwiched between transparent conducting electrodes (TCOs, see Section 3). 1.2 The test methods are applicable only for multilayered (two or more coatings between the TCOs) absorptive electrochromic coatings on sealed insulating glass (IG) units fabricated for vision glass (superstrate and substrate) areas for use in buildings, such as sliding doors, windows, skylights, and exterior wall systems. The multilayers used for electrochromically changing the optical properties may be inorganic or organic materials between the superstrate and substrate. 1.3 The electrochromic coatings used in this test method are exposed to solar radiation and are deployed to control the amount of radiation by absorption and reflection and thus, limit the solar heat gain and amount of solar radiation that is transmitted into the building. 1.4 The test methods are not applicable to other chromogenic devices, such as, photochromic and thermochromic devices. 1.5 The test methods are not applicable to electrochromic devices consisting of three layers of coatings including the two transparent conducting electrodes (see Section 3). 1.6 The test methods are not applicable to electrochromic windows that are constructed from superstrate or substrate materials other than glass. 1.7 The test methods referenced herein are laboratory tests conducted under specified conditions. These tests are intended to simulate and, in some cases, to also accelerate actual in-service use of the electrochromic windows. Results from these tests cannot be used to predict the performance with time of in-service units unless actual corresponding in-service tests have been conducted and appropriate analyses have been conducted to show how performance can be predicted from the accelerated aging tests. 1.8 The values stated in SI units are to be regarded as the standard. ......

Standard Test Methods for Assessing the Durability of Absorptive Electrochromic Coatings on Sealed Insulating Glass Units

JIS R 3205 ERRATUM 1:2010 勘误表

ERRATUM

KS L 2501-2010 玻璃瓶

이 표준은 유리병류(이하 유리병이라 한다.)에 대하여 규정한다.

Glass bottle

KS L 2408-2010 玻璃杯

이 표준은 소다석회 유리컵(이하 유리컵)에 대하여 규정한다. 다만, 손잡이 및 받침이 달린

Glass tumblers

CNCA 04C-028-2009 安全玻璃类强制性认证实施规则 安全玻璃产品

本规则适用于建筑、铁道车辆和汽车用与安全性能相关的各类玻璃产品，其中汽车用安全琉璃）。 与安全性能相关的汽车用玻璃包括夹层玻璃、钢化玻璃、夹层玻璃、塑玻复合材料、安全中空玻璃等；与安全性能相关的建筑用玻璃产品包括夹层玻璃、钢化玻璃、夹层玻璃、塑玻复合材料、（安全）中空玻璃等；与安全性能相关的铁道车辆用玻璃产品包括前窗夹层玻璃、前窗以外用夹层玻璃、钢化玻璃及安全中空玻璃等。

Implementation Rules for Compulsory Certification of Safety Glass Safety Glass Products

JC/T 2001-2009 太阳电池用玻璃

本标准规定了太阳电池用玻璃的术语和定义、材料、技术要求、试验方法、检验规则、标志、包装、运输及贮存。 本标准适用于晶体硅太阳电池组件用玻璃。 平板型太阳集热器用盖板玻璃、薄膜太阳电池组件用玻璃也可参照本标准中相应条款。

Glass for solar cell module

ASTM F2248-09 用夹层玻璃制造的防爆玻璃窗的等效3秒持续时间设计负荷规定的标准实施规范

This practice provides a design load suitable for sizing blast resistant glazing comprised of laminated glass or insulating glass fabricated with laminated glass. Blast resistant glazing comprised of laminated glass or insulating glass fabricated with laminated glass shall be sized to resist the 3-second duration equivalent design loading from this standard practice using the procedures described in Practice E1300. Blast resistant glazing comprised of laminated glass or insulating glass fabricated with laminated glass sized using the 3-second design loading determined from this practice will fracture safely in the event of a blast, thus reducing the potential for personal injury, structural and non-structural building damage, and cleanup costs should an explosion occur. In the event a blast loading never occurs to blast resistant glazing comprised of laminated glass or insulating glass fabricated with laminated glass sized using the 3-second duration loading determined herein, the blast resistant glazing will have a probability of breakage less than or equal to 8 lites per 1000 at the first occurrence of a loading equal to the 3-second duration design loading determined herein. Blast resistant glazing designed to resist the 3-second equivalent load as determined herein, properly supported, will perform to minimal hazard as defined in Test Method F1642.1.1 This practice sets forth a method to specify an equivalent 3-second design loading suitable to use with Practice E1300 to select the thickness and type of blast resistant glazing fabricated with laminated glass to glaze a fenestration. Glass plies used to construct laminated glass are recommended to be either annealed or heat strengthened glass. 1.2 This practice applies to blast resistant glazing fabricated using laminated glass only, including single laminated glass and insulating glass fabricated with laminated glass. As a minimum, insulating glass shall use laminated glass for the inboard (protected side) lite. 1.3 This practice assumes that blast resistant glazing shall be adhered to its supporting frame using structural silicone sealant or adhesive glazing tape. The width of the structural silicone sealant bead shall be at least equal to the larger of 10-mm (3/8-in.) or the thickness designation of the glass to which it adheres but not larger than two times the thickness designation of the glass to which it adheres. The minimum thickness of the structural silicone bead shall be 5-mm (3/16-in.). The width of glazing tape shall be at least equal to two times but not more than four times the thickness designation of the glass to which it adheres. The width of silicone or glazing tape is referred to as bite and is shown and discussed in Guide C1564. 1.4 This practice assumes that the structural silicone bead or glazing tape is applied to both sides of single lite laminated glass but need only be applied to the inboard side (protected side) of insulating glass. 1.5 This practice assumes the framing members shall restrict deflections of edges of blast resistant glazing they support to L/60 under 2.0× the load resistance of the blast resistant glazing for inward loading, where L denotes the length of the supported edge. 1.6 This practice assumes the framing system supporting the blast resistant glazing sha......

Standard Practice for Specifying an Equivalent 3-Second Duration Design Loading for Blast Resistant Glazing Fabricated with Laminated Glass

ASTM D4030/D4030M-09e1 玻璃纤维绳和缝纫线的标准规范

1.1 This specification covers the requirements for continuous glass filament sewing thread; and continuous filament cord, untreated and neoprene treated. 1.2 This specification is intended to assist ultimate users by designating the types of these products that are typical in the industry. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Glass Fiber Cord and Sewing Thread

BS 3193:2008 家用器具热钢化玻璃嵌板规范

This British Standard specifies requirements for thermally toughened glass panels for use in domestic appliances where such panels can be exposed to thermal and/or physical shock. Methods of test for fragmentation and for resistance to thermal shock and impact are given in Annexes A , B and C respectively. Recommendations for manufacturers of domestic appliances on the use of glass panels are given in Annex D . Guidance on handling glass is given in Annex E. This British Standard does not specify performance requirements for glass panels in respect of abrasion or chemical resistance.

Specification for thermally toughened glass panels for use in domestic appliances

GOST R 51136-2008 防护夹层玻璃.总规范

Protective laminate glass. General specifications

ASTM F1233-08(2013) 安全玻璃材料和系统的标准试验方法

6.1 This test method is based on field experience rather than laboratory analysis. It provides a basis for the comparative evaluation of ballistic/forced entry/containment resistance of security glazings and systems and should not be used to establish or confirm the absolute prevention of forcible entries or forced exits. This test method defines three factors which determine the success or failure of any attempt to forcefully enter (or exit) the glazing or system. They are: (1) the tools employed, (2) the techniques and methods used by the attackers, and (3) the total time available to effect the entry or exit. This test method defines two of the three factors (tools and techniques) and allows the third (duration) to vary in order to establish levels of forced entry or exit resistance. 1.1 This test method sets forth procedures whose purpose is limited to the evaluation of the resistance of security glazing materials and systems against the following threats: 1.1.1 Ballistic Impact, 1.1.2 Blunt Tool Impacts, 1.1.3 Sharp Tool Impacts, 1.1.4 Thermal Stress, and 1.1.5 Chemical Deterioration. Note 1—Specifically exempted from this test method are the use of power (motor or engine-driven) tools or devices, explosives, military ordinance (excepting small arms) and tools, processes or devices requiring more than two persons to transport and operate. 1.2 The values stated in inch-pounds are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For a specific warning statement, see Warning in 10.1.1.6.

Standard Test Method for Security Glazing Materials And Systems

JC 846-2007 贴膜玻璃

本标准规定了贴膜玻璃的术语及定义、分类、技术要求、检验规则和包装、标志、运输、贮存。 本标准适用于建筑用贴膜玻璃，其它场所用贴膜玻璃可参照使用。

Film mounted glass

CAS 141-2007 汽车玻璃窗膜技术规范

本规范规定了汽车玻璃窗膜的主要技术要求和试验方法、汽车玻璃窗贴膜工艺技术条件、质量要求、标志、包装和贮存。 本规范适用于汽车玻璃窗膜,也适用于汽车玻璃窗贴膜工艺和质量要求。

Technical Criterions for Automotive Window Film

JIS R 3301 AMD 1:2007 路标漆用玻璃微珠(修改件1)

JIS R 3301:1995を，次のように改正する。

Glass beads for traffic paint (Amendment 1)

ANSI/NGA R1.1-2007 夹层汽车玻璃检修标准

Defines (1) Repairable Damages; (2) The process of windshield repair: and; (3) The performance criteria for repaired glass. The standard also provides best practices for the training of a repair technician.

Repair of Laminated Automotive Glass Standard (ROLAGS)

KS L 2410-2006 碳酸饮料玻璃瓶

이 규격은 내용물의 압력이 20 ℃에서 0.49 MPa(게이지 압력) 이하인 탄산 음료용

Carbonated beverage bottles