Q62 石膏制品 标准查询与下载

GA 223-2004 石膏研究组产品种类、用途、面积、标准

Metric (SI) thicknesses are the industry accepted metric designations for gypsum panel product thicknesses. Contact the manufacturer for the availability of gypsum panel products in hard metric (SI) widths and lengths.

GYPSUM PANEL PRODUCTS TYPES, USES, SIZES, AND STANDARDS

GA 239-2004 在湿润地区瓷砖的耐水石膏板后盾

Water-resistant gypsum backing board (see ASTM C 1396/C 1396M, Standard Specification for Gypsum Board), commonly called “green board” because of the color of its face paper, is specially designed and formulated to serve as a base for ceramic and similar tile in areas subject to occasional water or moisture such as tub and shower enclosures, kitchens, and utility rooms. The core, face paper, and back paper are formulated and manufactured to resist the effects of moisture and humidity.

WATER-RESISTANT GYPSUM BACKING BOARD FOR CERAMIC TILE IN WET AREAS

GA 254-2004 耐火石膏护套

Gypsum sheathing is most commonly manufactured with a water-resistive treated core but may be available in a nontreated core. Treated core gypsum sheathing is a versatile, economical, water-repellent panel sheathing and is intended for use as a substrate sheathing under a variety of exterior wall claddings in any climate. Nontreated core gypsum sheathing is intended for

Fire-Resistant Gypsum Sheathing

ASTM C587-04(2009) 石膏饰面板标准规范

1.1 This specification covers calcined gypsum mixed at the mill with other ingredients to control working quality and setting time; specifically designed as a veneer plaster to be applied over gypsum base for veneer plasters, masonry or concrete surfaces to a maximum thickness of ¼ in. (6.4 mm) providing a surface ready for decoration. Note 18212;Specification C843 contains application procedures for gypsum veneer plaster. 1.2 This specification covers test methods for determining the physical properties of gypsum veneer plasters and sets forth minimum requirements that must be met. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes shall not be considered as requirements of the standard. 1.5 The following safety hazards caveat applies only to the Test Methods portion, Section 5 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Gypsum Veneer Plaster

ASTM C587-04(2014) 石膏饰面板标准规格

1.1 This specification covers calcined gypsum mixed at the mill with other ingredients to control working quality and setting time; specifically designed as a veneer plaster to be applied over gypsum base for veneer plasters, masonry or concrete surfaces to a maximum thickness of 1/4 in. (6.4 mm) providing a surface ready for decoration.Note 1—Specification C843 contains application procedures for gypsum veneer plaster. 1.2 This specification covers test methods for determining the physical properties of gypsum veneer plasters and sets forth minimum requirements that must be met. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes shall not be considered as requirements of the standard. 1.5 The following safety hazards caveat applies only to the Test Methods portion, Section 5 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Gypsum Veneer Plaster

ASTM C754-04 用螺钉安装石膏墙板的钢框构件安装的标准规范

1.1 This specification covers the minimum requirements for the installation of interior nonstructural steel framing and furring members designed to receive screw-attached gypsum panel products. The steel framing and furring members covered in this specification are limited to those complying with Specification C645. 1.2 Details of construction for a specific assembly to achieve the required fire resistance shall be obtained from reports of fire-resistance tests, engineering evaluations, or listings from recognized fire testing laboratories. 1.3 The values stated in inch-pound units are to be regarded as the standard. The SI (metric) values given in parentheses are approximate and are provided for information purposes only.

Standard Specification for Installation of Steel Framing Members to Receive Screw-Attached Gypsum Panel Products

ASTM C1597M-04(2009)e1 石膏墙板规范(公制尺寸)

1.1 This specification covers gypsum wallboard which is designed to be used for walls, ceilings, or partitions and affords a surface suitable to receive decoration. Note 18212;Specification C 840 contains application procedures for gypsum wallboard. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. For gypsum wallboard produced to inch-pound units see Specification C 1396/C 1396M. 1.3 The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.

Standard Specification for Gypsum Wallboard (Hard Metric Sizes)

ASTM C840-04a 石膏板的加工和应用的标准规范

1.1 This specification covers the minimum requirements for the methods of application and finishing of gypsum board, including related items and accessories. 1.2 Details of construction for a specific assembly to achieve the required fire resistance shall be obtained from reports of fire-resistance tests, engineering evaluations, or listings from recognized fire testing laboratories.1.2.1 Where this specification is more stringent (size or thickness of framing: size and spacing of fasteners) than the fire-rated construction, this specification shall govern. 1.3 Where sound control is required for a gypsum board assembly, details of construction shall be in accordance with reports of acoustical tests of assemblies that have met the required acoustical values. 1.4 Unheated spaces above gypsum board ceilings shall be properly ventilated (see Appendix X2). 1.5 The various application systems are located in the following sections: I Application of Single-Ply Gypsum Board to Wood Framing Members 8II Application of Two-Ply Gypsum Board to Wood Framing Members9III Application of Gypsum Board by Adhesive Nail-On to Wood Framing Members10IV Semi-Solid Gypsum Board Partitions11V Solid Gypsum Board Partitions12VI Application of Gypsum Board with Adhesives to Interior Masonry or Concrete Walls13VII Application of Gypsum Board to Rigid Foam Insulation14VIII Application of Gypsum Board to Steel Framing and Furring15IX Arches and Bending Radii16X Application of Gypsum Board to Receive Tile by Adhesive Application17XI Exterior Application of Gypsum Wallboard and Exterior Gypsum Soffit Board18XII Floating Interior Angles19XIII Control (Expansion) Joints20XIV Foil-Backed Gypsum Board21 The values stated in inch-pound units are to be regarded as the standard. The SI (metric) values given in parentheses are approximate and are provided for information purposes only. 1.6 The text of this specification references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification. 1.7 The following precautionary caveat pertains only to Sections 6-23. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.7.1 For specific precautionary statements, see 4.1.1, 4.1.2 and 22.5.

Standard Specification for Application and Finishing of Gypsum Board

ASTM C840-04 石膏板的加工和应用的标准规范

1.1 This specification covers the minimum requirements for the methods of application and finishing of gypsum board, including related items and accessories. 1.2 Details of construction for a specific assembly to achieve the required fire resistance shall be obtained from reports of fire-resistance tests, engineering evaluations, or listings from recognized fire testing laboratories.1.2.1 Where this specification is more stringent (size or thickness of framing: size and spacing of fasteners) than the fire-rated construction, this specification shall govern. 1.3 Where sound control is required for a gypsum board assembly, details of construction shall be in accordance with reports of acoustical tests of assemblies that have met the required acoustical values. 1.4 Unheated spaces above gypsum board ceilings shall be properly ventilated (see Appendix X2). 1.5 The various application systems are located in the following sections: I Application of Single-Ply Gypsum Board to Wood Framing Members 8II Application of Two-Ply Gypsum Board to Wood Framing Members9III Application of Gypsum Board by Adhesive Nail-On to Wood Framing Members10IV Semi-Solid Gypsum Board Partitions11V Solid Gypsum Board Partitions12VI Application of Gypsum Board with Adhesives to Interior Masonry or Concrete Walls13VII Application of Gypsum Board to Rigid Foam Insulation14VIII Application of Gypsum Board to Steel Framing and Furring15IX Arches and Bending Radii16X Application of Gypsum Board to Receive Tile by Adhesive Application17XI Exterior Application of Gypsum Wallboard and Exterior Gypsum Soffit Board18XII Floating Interior Angles19XIII Control (Expansion) Joints20XIV Foil-Backed Gypsum Board21 The values stated in inch-pound units are to be regarded as the standard. The SI (metric) values given in parentheses are approximate and are provided for information purposes only. 1.6 The text of this specification references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification. 1.7 The following precautionary caveat pertains only to Sections 6-23. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.7.1 For specific precautionary statements, see 4.1.1, 4.1.2 and 22.5.

Standard Specification for Application and Finishing of Gypsum Board

ASTM C844-04 石膏饰面粉饰用石膏基底的应用标准规范

1.1 This specification covers the minimum requirements for, and methods of, application of gypsum veneer base for gypsum veneer plasters.1.2 Gypsum veneer base shall not be used as a base for direct adhesive application of ceramic, metal, or plastic tile in areas exposed to abnormal moisture or humidity or temperature.1.3 Details of construction for a specific assembly to achieve the required fire resistance shall be obtained from reports of fire-resistance tests, engineering evaluations, or listings from recognized fire testing laboratories.1.4 Where a specific degree of sound control is required for veneer plaster assemblies and constructions, details of construction shall be in accordance with official reports of tests conducted in recognized sound testing laboratories in accordance with the applicable sound tests, Test Method C 423, Test Method E 90, or Test Method E 492.1.5 Where this specification is more stringent (size or thickness of framing; spacing of fasteners) than the fire-rated construction, this specification shall govern; otherwise, the construction described in the fire test report shall govern.1.6 Unheated spaces above gypsum veneer base ceilings shall be properly ventilated (see ).1.7 The values stated in inch-pound units are to be regarded as the standard. The SI (metric) values given in parentheses are approximate and are provided for information purposes only.1.8 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.

Standard Specification for Application of Gypsum Base to Receive Gypsum Veneer Plaster

ASTM C1597M-04 石膏墙板的标准规范

1.1 This specification covers gypsum wallboard which is designed to be used for walls, ceilings, or partitions and affords a surface suitable to receive decoration.Note 18212;Specification C 840 contains application procedures for gypsum wallboard.1.2 The values are stated in SI (metric) units only and are to be regarded as standard. For gypsum wallboard produced to inch-pound units see Specification C 36/C 36 M.1.3 The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.

Standard Specification for Gypsum Wallboard (Hard Metric Sizes)

ASTM C954-04 将厚度为0.033至0.112英寸(0.84至2.84mm)的石膏板或金属熟石膏基板安装在钢骨上所用的钻孔钢螺钉的标准规范

1.1 This specification covers minimum requirements for steel drill screws for use in fastening gypsum panel products or metal plaster bases to steel members from 0.033 in. (0.84 mm) to 0.112 in. (2.84 mm) in thickness. 1.2 This specification also covers physical properties and test methods for determining performance requirements. 1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 The following safety hazards caveat pertains only to the test methods described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Steel Drill Screws for the Application of Gypsum Panel Products or Metal Plaster Bases to Steel Studs from 0.033 in. (0.84 mm) to 0.112 in. (2.84 mm) in Thickness

ASTM C587-04 石膏饰面板的标准规范

1.1 This specification covers calcined gypsum mixed at the mill with other ingredients to control working quality and setting time; specifically designed as a veneer plaster to be applied over gypsum base for veneer plasters, masonry or concrete surfaces to a maximum thickness of 1/4 in. (6.4 mm) providing a surface ready for decoration.Note 1Specification C 843 contains application procedures for gypsum veneer plaster.1.2 This specification covers test methods for determining the physical properties of gypsum veneer plasters and sets forth minimum requirements that must be met.1.3 The values stated in inch-pound units are to be regarded as the standard. The SI (metric) values given in parentheses are approximate and are provided for information purposes only.1.4 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes shall not be considered as requirements of the standard.The following safety hazards caveat applies only to the Test Methods portion, Section of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Gypsum Veneer Plaster

ASTM C1395/C1395M-04 石膏天花板规范

1.1 This specification covers 1/2 in. [12.7 mm] thick gypsum ceiling board designed for use on interior ceilings with framing spaced not more than 24 in. [610 mm] on center and that affords a surface suitable to receive water-based texture and other decoration. This product is also suitable for use on interior walls.Note 18212;Specification C 840 contains application procedures for gypsum ceiling board.1.2 The values stated in either inch-pound units or SI (metric) are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system shall be used independent of the other. Values from the two systems shall not be combined.

Specification for Gypsum Ceiling Board

ASTM C1002-04 木销或钢销上石膏板制品或金属熟石膏基板用自攻钢螺钉标准规范

1.1 This specification covers steel self-piercing tapping screws for use in fastening gypsum panel products and metal plaster bases to cold-formed steel studs less than 0.033 in. (0.84 mm) in thickness and wood members and for fastening gypsum panel products to gypsum board. 1.2 This specification also covers test methods for determining performance requirements and physical properties. 1.3 The values stated in inch-pound units are to be regarded as the standard. The SI (metric) values given in parentheses are approximate and are for information only. 1.4 The following safety hazards caveat pertains only to the test methods described in this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Steel Self-Piercing Tapping Screws for the Application of Gypsum Panel Products or Metal Plaster Bases to Wood Studs or Steel Studs

ASTM C11-04 石膏及相关建筑材料和系统的标准术语

1.1 This standard contains terminology relating to gypsum and related building materials and systems. The terms are generically defined. More specific and expanded definitions may appear in appropriate standards.

Standard Terminology Relating to Gypsum and Related Building Materials and Systems

ASTM C1280-04 石膏外保护壳应用的标准规范

1.1 This specification covers the minimum requirements for and methods of application of gypsum sheathing for use as a substrate for exterior wall cladding.1.2 Details of construction for a specific assembly to achieve the required fire resistance shall be obtained from reports of fire-resistance tests, engineering evaluations, or listings from recognized fire testing laboratories.1.2.1 This specification shall govern where it is more stringent (size or thickness of framing and size and spacing of fasteners) than the fire-rated construction.1.3 Where sound control is required for a gypsum sheathing assembly, the details of construction shall be in accordance with the acoustical test report of an assembly that has met the required acoustical value(s).1.3.1 This specification shall govern where it is more stringent (size or thickness of framing and size and spacing of fasteners) than the sound-rated construction.1.4 Where resistance to racking loads or shear is required for a gypsum sheathing assembly, the details of construction shall be in accordance with the racking or shear test report of an assembly that has met the required racking or shear value(s).1.4.1 This specification shall govern where it is more stringent (size or thickness of framing and size and spacing of fasteners) than the racking or shear-tested construction.1.5 The values stated in inch-pound units are to be regarded as the standard. The SI (metric) values given in parentheses are approximate and are provided for information purposes only.1.6 The text of this standard references footnotes which provide explanatory material. These footnotes shall not be considered as requirements of the standard.1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Application of Gypsum Sheathing

SANS 266:2003 石膏板

Specifies the requirements for gypsum plasterboard that is intended to be used as vertical or horizontal linings in buildings, but does not include plasterboard that has been subjected to secondary manufacturing operations. Includes boards manufactured t

Gypsum plasterboard

NF P72-204-2/A1:2003 DTC 25.42.建筑施工.专门合同.使用石膏复合板的内部绝缘和墙衬.第2部分:特殊条款

DTU 25.42 - Building works - Private contracts - Internal insulation and wall linings using gypsum composite panels - Part 2 : special clauses.

NF P72-204-1/A1:2003 DTU 25.42.建筑工程.使用石膏复合板的内部绝缘和墙衬.第1部分:技术规范

DTU 25.42 - Building works - Internal insulation and wall linings using gypsum composite panels - Part 1 : technical specifications.