Q62 石膏制品 标准查询与下载

BS EN 15319:2007 纤维(石膏)抹灰层设计的一般原则

This European Standard defines the principles for the design of works carried out using fibrous (gypsum) plaster products as defined in EN 13815. Fibrous (gypsum) plaster casts from the three categories of production below (see Clause 4 of EN 13815:2006) should be involved: a) ”cpp” allowing regulatory marking CE; b) “cppv” allowing regulatory marking CE; c) “ipp” either when CE marking is required; or without CE marking (see Annex D – Note 2 of EN 13815:2006). This European Standard applies to both new constructions and to the refurbishment, restructuring or conversion of existing buildings. The common fields of application of fibrous plaster are as set out in Table 1 below. This European Standard should not apply to:  works formed from fibre reinforced gypsum sheet products, that are the subject of prEN 15283;  suspended ceilings formed from gypsum units and/or tills, installed dry in a framework, that are the subject of EN 14246;  works formed of solid casts;  run moulded plaster works formed in situ;  works formed from plaster based stucco casts, carton-pierre decors, resin decors;  fibrous plaster works which, by their nature, do not from an integral part of the structure by the use of permanent fixing (e.g. exhibition stands);  fibrous plaster works consisting of casts and embellishments, when they are to be applied directly to either new or existing wall or ceiling surfaces, for purely decorative applications (see Figures 3 and 4). Works of these types should be carried out in accordance with standard practice. This European Standard does not contain the regulatory requirements with which fibrous plaster works e.g. ceilings need to comply in certain buildings. NOTE In the field of safety, the main regulations relate to certain types of buildings, for example:  public buildings (PB);  high rise buildings (HRB);  buildings for educational purposes;  buildings for sanitary purposes. This European Standard does not deal with the ability of fibrous plastering works to comply with particular technical requirements (e.g. acoustical) needed in order for the works to comply with the requirements of the particular building contract.

General principles of design of fibrous (gypsum) plaster works

JC/T 799-2007 装饰石膏板

本标准规定了浇注成型的装饰石膏薄板的术语、分类、要求、试验方法、检验规则以及包装、标志、运输和贮存。 本标准适用于用作室内墙面装饰和吊顶的装饰石膏板。

Decorating gypsum board

DIN 18181:2007 楼房建筑用石膏灰泥板.应用

Gypsum plasterboards for building construction - Application

JIS A 6901 ERRATUM 2:2007 勘误

ERRATUM

DIN 18180:2007 石膏板.类型和要求

The standard applies to factory-produced gypsum plasterboards which are made of two sheets of mill-board affixed firmly to a layer of gypsum plaster between them. Gypsum plasterboards for various applications are defined, including those used as dry lining with or without additional fire resistance properties and those used as baseboards for plaster. Dimensions, mass in relation to surface, failure loads and degrees of deflection are given.#,,#

Gypsum plasterboards - Types and requirements

ASTM C11-07b 与石膏及其相关建筑材料和系统相关的标准术语

1.1 This standard covers terminology relating to gypsum and related building materials and systems. The terms are generically defined. More specific and expanded definitions may appear in appropriate standards.

Standard Terminology Relating to Gypsum and Related Building Materials and Systems

ASTM C1278/C1278M-07a 纤维增强石膏镶板标准规范

1.1 This specification covers fiber-reinforced gypsum panels described in .1.1.1 Interior Fiber-Reinforced Gypsum Panels are designed to be used for walls, ceilings, or partitions and affords a suitable surface to receive decoration.1.1.2 Water-Resistant Fiber-Reinforced Gypsum Backing Panels are designed primarily to be used as a base for the application of ceramic or plastic tile on walls or ceilings. This product is also suitable for decoration.1.1.3 Exterior Fiber-Reinforced Gypsum Soffit Panels are designed for use on exterior soffits and carport ceilings that are completely protected from contact with liquid water.1.1.4 Water-Resistant Exterior Fiber-Reinforced Gypsum Sheathing Panels are designed for use as sheathing on buildings.1.1.5 Interior Fiber-Reinforced Gypsum Underlayment Panelsare designed for use as a base for application of finished flooring materials.1.1.6 Fiber-Reinforced Gypsum Board Panelsare designed for use in roofing systems.1.2 Specifications applicable to all fiber-reinforced gypsum panels are located in Sections and except as modified by applicable product sections. Specifications applicable to specific panels are located in the following sections:1.3 The values stated in either inch-pound units or SI (metric) are to be regarded separately as the standard. Within the text, the SI units are shown in brackets. The values stated in each system shall be used independently of the other. Values from the two systems shall not be combined.1.4 The text of this specification references notes and footnotes that provide explanatory material. These notes and footnotes shall not be considered as requirements of the standard.

Standard Specification for Fiber-Reinforced Gypsum Panel

ASTM C1280-07 石膏盖板的标准规范

1.1 This specification covers the minimum requirements for and methods of application of gypsum sheathing for use as a substrate for exterior wall cladding. 1.2 Details of construction for a specific assembly to achieve the required fire resistance shall be obtained from reports of fire-resistance tests, engineering evaluations, or listings from recognized fire testing laboratories. 1.2.1 This specification shall govern where it is more stringent (size or thickness of framing and size and spacing of fasteners) than the fire-rated construction. 1.3 Where sound control is required for a gypsum sheathing assembly, the details of construction shall be in accordance with the acoustical test report of an assembly that has met the required acoustical value(s).1.3.1 This specification shall govern where it is more stringent (size or thickness of framing and size and spacing of fasteners) than the sound-rated construction. 1.4 Where resistance to racking loads or shear is required for a gypsum sheathing assembly, the details of construction shall be in accordance with the racking or shear test report of an assembly that has met the required racking or shear value(s). 1.4.1 This specification shall govern where it is more stringent (size or thickness of framing and size and spacing of fasteners) than the racking or shear-tested construction. 1.5 The values stated in inch-pound units are to be regarded as the standard. The SI (metric) values given in parentheses are approximate and are provided for information purposes only. 1.6 The text of this standard references footnotes which provide explanatory material. These footnotes shall not be considered as requirements of the standard. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Application of Gypsum Sheathing

ASTM C1278/C1278M-07a(2011) 纤维增强石膏镶板标准规格

1.1 This specification covers fiber-reinforced gypsum panels described in 1.1.1-1.1.4. 1.1.1 Interior Fiber-Reinforced Gypsum Panels are designed to be used for walls, ceilings, or partitions and affords a suitable surface to receive decoration. 1.1.2 Water-Resistant Fiber-Reinforced Gypsum Backing Panels are designed primarily to be used as a base for the application of ceramic or plastic tile on walls or ceilings. This product is also suitable for decoration. 1.1.3 Exterior Fiber-Reinforced Gypsum Soffit Panels are designed for use on exterior soffits and carport ceilings that are completely protected from contact with liquid water. 1.1.4 Water-Resistant Exterior Fiber-Reinforced Gypsum Sheathing Panels are designed for use as sheathing on buildings. 1.1.5 Interior Fiber-Reinforced Gypsum Underlayment Panels are designed for use as a base for application of finished flooring materials. 1.1.6 Fiber-Reinforced Gypsum Board Panels are designed for use in roofing systems. 1.2 Specifications applicable to all fiber-reinforced gypsum panels are located in Sections 1-4 and 11-13 except as modified by applicable product sections. Specifications applicable to specific panels are located in the following sections: Interior Fiber-Reinforced Gypsum Panels5 Water-Resistant Fiber-Reinforced Gypsum Backing Panels6 Exterior Fiber-Reinforced Gypsum Soffit Panels7 Water-Resistant Exterior Fiber-Reinforced Gypsum Sheathing Panels8 Interior Fiber-Reinforced Gypsum Underlayment Panels9 Fiber-Reinforced Gypsum Roof Board Panels10 1.3 The values stated in either inch-pound units or SI (metric) are to be regarded separately as the standard. Within the text, the SI units are shown in brackets. The values stated in each system shall be used independently of the other. Values from the two systems shall not be combined. 1.4 The text of this specification references notes and footnotes that provide explanatory material. These notes and footnotes shall not be considered as requirements of the standard.

Standard Specification for Fiber-Reinforced Gypsum Panel

ASTM C840-07 石膏板的应用和修整用标准规范

1.1 This specification covers the minimum requirements for the methods of application and finishing of gypsum board, including related items and accessories. 1.2 Details of construction for a specific assembly to achieve the required fire resistance shall be obtained from reports of fire-resistance tests, engineering evaluations, or listings from recognized fire testing laboratories.1.2.1 Where this specification is more stringent (size or thickness of framing: size and spacing of fasteners) than the fire-rated construction, this specification shall govern. 1.3 Where sound control is required for a gypsum board assembly, details of construction shall be in accordance with reports of acoustical tests of assemblies that have met the required acoustical values.1.4 Unheated spaces above gypsum board ceilings shall be properly ventilated (see Appendix X2).1.5 The various application systems are located in the following sections: The values stated in inch-pound units are to be regarded as the standard. The SI (metric) values given in parentheses are approximate and are provided for information purposes only. 1.6 The text of this specification references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification. 1.7 The following precautionary caveat pertains only to Sections 6-24. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.7.1 For specific precautionary statements, see 4.1.1, 4.1.2, and 22.5.

Standard Specification for Application and Finishing of Gypsum Board

ASTM C11-07 与石膏及其相关建筑材料和系统相关的标准术语

1.1 This standard covers terminology relating to gypsum and related building materials and systems. The terms are generically defined. More specific and expanded definitions may appear in appropriate standards.

Standard Terminology Relating to Gypsum and Related Building Materials and Systems

ASTM C11-07a 与石膏及其相关建筑材料和系统相关的标准术语

1.1 This standard covers terminology relating to gypsum and related building materials and systems. The terms are generically defined. More specific and expanded definitions may appear in appropriate standards.

Standard Terminology Relating to Gypsum and Related Building Materials and Systems

KS L 9203-2006 防水石膏护板

이 규격은 목욕탕이나 샤워장에 도자기 타일이나 플라스틱제 타일을 시공하기 위한 배킹보드

Water resistant gypsum backing board

KS L 9013-2006 石膏混凝土

이 규격은 하소 석고와 적당한 골재를 섞은 것으로 작업할 때 물을 가하여 사용하는 석고

Gypsum concrete

DIN EN 13815:2006 纤维石膏模型.定义.要求和试验方法

This European Standard specifies the characteristics and performance requirements for fibrous gypsum plaster cast sections, rigid sheets, rigid tiles - made by various techniques in factories or workshops. This European Standard is applicable to: - conventional series producted products; - series produced products with varying properties; - individual (and non-series) produced products, insofar required to be CE marked. See 4.1 and annex D concerning the classification of the fibrous gypsum plaster casts. This European Standard covers the following performance characteristics of the fibrous gypsum plaster casts: reaction to fire, thermal resistance, as well as resistance to impact by a hard steel ball and cohedion. The following performance characteristics are linked to systems assembled with fibrous gypsum plaster casts: fire resistance, impact resistance, direct airborne sound insulation, acoustic absorption to be measures according to the corresponding European test methods. If required, tests have to be done on assembled systems simulating the end use conditions. This European Standard defines the reference test methods for the technical specifications. This European Standard also covers additional technical characteristics of fibrous gypsum plaster casts that are of importance for use and acceptance of the products by the building industry and the reference tests for these characteristics. It provides for assessment of conformity of the products to this standard. This standard does not apply to: i) fibre reinforced gypsum sheet products (see pr EN 15283); ii) gypsum elements for suspended ceilings (see EN 14246); iii) solid casts; iv) run fibre reinforced products; v) plaster based stucco casts, carton pierre decors, resin decors; vi) moulds, models and mock-ups made of fibrous gypsum plaster; vii) fibrous gypsum plaster casts that, by nature, are not intended to be fastended in position; viii) fibrous gypsum plaster casts for sets (theatre, cinema, TV); ix) fibrous gypsum plaster casts and decors intended to be installed directly on existing partitions, walls and ceilings, for purely decorative applications.

Fibrous gypsum plaster casts - Definitions, requirements and test methods; English version of DIN EN 13815:2006-12

KS L 5315-2006 石膏板用石膏材料

이 규격은 판재 시공용 석고 바탕재에 대하여 규정한다.

Gypsum base for veneer plasters

DIN EN 13963 Berichtigung 1:2006 石膏抹灰板用填缝材料.定义、要求和试验方法

Jointing materials for gypsum plasterboards - Definitions, requirements and test methods; German version EN 13963:2005, Corrigenda to DIN EN 13963:2005-08; German version EN 13963:2005/AC:2006

DIN EN 14195 Berichtigung 1:2006 石膏灰泥板系统用金属框架部件.定义、要求和试验方法

This document specifies the characteristics of metal framing components intended to be used in building construction works in conjunction with gypsum plasterboard conforming to EN 520 and Gypsum plasterboard products from reprocessing conforming to EN 14190 where the assembly is non-loadbearing. These are, for example, partitions, wall and ceiling linings and the cladding of beams, columns, ducts and lift shafts.#,,#

Metal framing components for gypsum plasterboard systems - Definitions, requirements and test methods; German version EN 14195:2005, Corrigenda to DIN EN 14195:2005-05; German version EN 14195:2005/AC:2006

BS EN 13815:2006 纤维石膏模型.定义.要求和试验方法

Fibrous gypsum plaster casts - Definitions, requirements and test methods

DIN EN 14246:2006 吊顶石膏成分.定义、要求和试验法

Gypsum elements for suspended ceilings - Definitions, requirements and test methods English version of DIN EN 14246:2006-09