共找到 183 条与 公路车辆使用、维护与修理 相关的标准,共 13 页
The SAE Vehicle E/E Systems Diagnostic Committee (Diagnostics committee) was formed in June, 1987 to address concerns of the automotive manufacturers and the automotive repair industry relating to repair of the increasingly complex electronic systems on new vehicles. This Handbook Supplement is a compilation of Standards dealing with on-board diagnostics.
On-Board Diagnostics for Light and Medium Duty Vehicles Standards Manuals IMAGES ARE NOT INCLUDED; PLEASE REFER TO GLOBAL
The document applies to the safety requirements on construction, equipment and verification of washing machinery for motor and rail vehicles operated in or outside buildings. It applies also to vehicle polishing machinery, which is part of vehicle washing machinery or independent machinery.
Safety of machinery - Vehicle washing machines - Safety requirements, test methods
Repair-touring activity. Repair-touring of lightweight vehicles. Service specifications.
General technical specification for the maintenance of urban passenger transport vehicles
Technical specification for urban transit cars being overhauled.Tram cars
Accident repair of light vehicles. Technical specifications.
Technical conditions for the opening of automobile overhaul enterprises
Specifications for automobile front axles and steering systems being overhauled
Specifications for automobile driving axles being overhauled
Specifications for automobile drive shafts being overhauled
Rules of Transportation of Dangerous Goods by Automobile
This standard gives principles for the specification of times in the field of maintenance. It specifies the rules for the structure of time systems and gives the definitions of some dates which are important for maintenance.
Maintenance; principles for specification of times and structure of time systems
This recommended practice provides a standard test procedure for comparing the fuel economy of components or systems of the type which can be switched from one vehicle to another in a short period of time. This test procedure is also ideally suited for comparing the fuel consumption of one vehicle to another, and one component of a combination vehicle to the same component in another. This procedure is specifically designed to be completed in one day. The test utilizes two medium to heavy duty in-service vehicles operated over interstate type highways. The relative fuel economy of the component, system, or vehicle under test is expressed as a percentage improvement or as a percentage of fuel saved. This factor is calculated using relative fuel consumption while operating with and without the test component, system, or vehicle under evaluation. Accuracy obtained from the use of this test procedure can be +/-1% when properly executed. This procedure is not intended to replace SAE J1264 oCT86, Joint RCCC/SAE Fuel Consumption Test Procedure or SAE J1321 OCT86, Joint TMC/SAE Fuel Consumption Test Procedure Type II, but will enhance a fleet's or manufacturer's ability to do a wide variety of fuel consumption tests on highway. The following basic rules must be applied to this procedure to ensure valid test results: a) A single test is inconclusive. A single test result may be an indicator. Test results must be repeatable to have validity; b) The more variables controlled, the more conclusive the results; c) All test procedures are accurate within prescribed limits. If the component, system or vehicle being tested by a given procedure shows a degree of improvement which is equal to or less than the accuracy limit of the procedure, an additional number of tests should be conducted to prove validity.
Joint TMC/SAE Fuel Consumption In-Service Test Procedure Type III
Technical requirements for automobile transmission being overhauled
Technical requirements for automobile engine camshafts being overhauled
Technical requirements for automobile frames being overhauled
Technical requirements for automobile engine cylinder blocks and cylinder heads being overhauled
Technical requirements for automobile engine crankshafts being overhauled
本标准规定了车库用手动和气动液压千斤顶(以下简称千斤顶)的结构型式、基本参数、技术要求、试验方法、检验规则和标志、包装、运输、贮存等。 本标准适用于表1所列各种型号的千斤顶。
garage jack
Completion and factory technical conditions for secondary maintenance of automobiles
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号