T05 专用材料及其制品 标准查询与下载

BS ISO 12219-4:2013 道路车辆的室内空气.汽车内饰零部件和材料中挥发性有机化合物排放的测定方法.小室法

Interior air of road vehicles. Method for the determination of the emissions of volatile organic compounds from vehicle interior parts and materials. Small chamber method

SAE J1648-2013 紧固件的防护涂料

This SAE Information Report is provided as an advisory guide. Careful discretion as to application is recommended. The content has been presented as accurately as possible, but responsiblity for its application lies with the user. It covers finishes applied to fasteners and related topics, corrosion resistance, lubricity, electrical grounding, ultraviolet light, and embrittlement. Table 1 lists these coatings and their properties so that finish selection can be reasonably made in accordance with known and anticipated fastener assembly applications. Application of protective coatings will affect fastener dimensions. This is especially critical for the thread

Protective Coatings for Fasteners

ISO 12219-4:2013 道路车辆内空气 第4部分 来自车辆内装品和材料的挥发性有机化合物释放的测定方法 小室法

This part of ISO 12219 specifies a qualitative and quantitative analytical method for vapour-phase organic compounds (volatile and some semi-volatile] released from car trim materials under Simulated real use conditions using Small emission test chambers (Small chamben. Small chambers are intended to provide atransfer function to vehicle level emissions. This method is intended for evaluating new car interior trim components but can, in principle, be applied to used car components. Target compounds include VOCs (conventionally defined as organic compounds in the volatility range Ph-hexane to Ph-hexadecanej and volatile carbonyl compounds such as formaldehyde. The specified analytical procedure for VOCs is ISO 16000-6 and for formaldehyde and some other light carbonyl compounds is ISO 16000-3. NOTE Compounds more volatile than pn-hexane andless volatile than np-hexadecane can also be analysed [See This part ofISO 12219 is complementarytoASTM D5116因andVDA 276,轩and providesthird partytest lapbporatories and manufacturing industry with an approach for: al identifyingthe effect ofreal use conditions on Specific VOC emissions datai D) comparing emissions from various assemblies with regards to specificVOC emissions; cj] evaluating and Sorting Specific assemblies regarding SpecificVOC emissions data; dj providing specific VOC emissions data to develop and verify a _ correlation between material level methods and the vehicle level method; el evaluating prototype，“low-emission ”assemblies during development.

Interior air of road vehicles - Part 4: Method for the determination of the emissions of volatile organic compounds from vehicle interior parts and materials - Small chamber method

SAE J2134-2012 道路车辆用安全门窗玻璃材料的光反射比

The scope of this SAE Performance Standard is to provide a simple, practical, and broadly applicable test procedure for appraising luminous Illuminant A reflectance of reflecting safety glazing materials for road vehicles. This SAE Performance Standard, which provides a simple test procedure widelys used in the optics field, may be used to measure the reflectivity which films applied to safety glazing materials for road vehicles man enhance. This test procedure applied to conditions where feasibility, rather than accuracy of measurement, is of prime importance. Measurements can be make outside laboratories in a quality control environment and in similar app

Luminous Reflectance in Safety Glazing Materials for Road vehicles

SAE J156-2012 易熔线

This standard covers supplemental requirements for low tension primary cable intended for use as Fusible Links (Fuse Links) at a nominal system voltage of 60 V DC (25 V AC) or less in surface vehicle electrical systems. These supplemental requirements are intended to qualify cables for an extreme current overload.

Fusible Links

SAE J912-2012 汽车装饰材料的抗粘连性及其相关特性的测定用试验方法

This test method is designed to indicate the degree of surface tackiness, color transfer, loss of embossment, and surface marring when two trim materials are placed face to face under specific conditions of time, temperature, and pressure. These specific conditions are not dictated in this test procedure but will be found in the material standards which govern each type of trim material to be tested.

Test Method for Determining Blocking Resistance and Associated Characteristics of Automotive Trim Materials

SAE J882-2012 汽车纺织物和塑料的测量厚度用试验方法

This test is designed to measure the thickness of relatively flat textiles, plastics, and similar materials.

Test Method for Measuring Thickness of Automotive Textiles and plastics

SAE J861-2012 对有机饰件材料的耐摩擦性测试方法

This test can be used to determine the resistance to color rub-off (crocking) of organic trim materials such as fabrics, vinyl coated fabrics, leather, coated fiberboard, and carpet. This method is similar to AATCC Method 8 - Colorfastness to Crocking.

Method of Testing Resistance to Crocking of Organic Trim Materials

CAB 1012-2012 汽车装饰用化纤制品

本标准规定了汽车装饰用化纤制品的术语和定义、产品分类、要求、检验方法、检验规则以及标志、包装、运输和贮存。 本标准适用于汽车装饰用化纤制品，其他用途的同类制品可参照执行。

Automobile decoration chemical products

SAE J2659-2012 通过形态测量聚合物材料的液体渗透测试方法

This test method described in this document covers a procedure to speciate that is, to determine the amounts of each different fuel constituent that permeates across sheets, films or slabs of plastic materials. One side of the sheet is meant to be in contact with either a liquid test fuel or a saturated test fuel vapor, the other side is meant to be exposed to an environment free of fuel. The test fuel can either be a mixture of a small (usually smaller than ten) number of hydrocarbon, alcohol and either constituents or it can be a sample of a real automotive fuel, e.g., one that may contain hundreds of different constituents. Furthermore, Appendix A contains guidelines to speciate evaporative emissions from finished fuel system components such as fuel lines, fuel filler pipes, fuel sender units, connectors and valves.

Test Method to Measure Fluid Permeation of Polymeric Materials by Speciation

ISO 12219-3:2012 公路车辆内空气.第3部分:来自车辆内装品和材料的挥发性有机化合物释放测定筛选法.微尺度室法

This part of ISO 12219 specifies a fast, qualitative and semiquantitative screening method for vapour-phase organic compounds (volatile and some semi-volatile) released from vehicle trim materials under simulated realuse conditions using micro-scale test chambers. This method is intended for evaluating new car interior trim components but can, in principle, also be applied to used car components. Target analytes include VOCs (conventionally defined as organic compounds in the volatility range of n-hexane to n-hexadecane) and volatile carbonyl compounds such as formaldehyde. The specified analytical procedure for VOCs is ISO 16000-6 and for formaldehyde and some other light carbonyl compounds is ISO 16000-3. NOTE 1 Some compounds more volatile than n-hexane and less volatile than n-hexadecane can also be analysed (for more information, see: ISO 16000-6:2011, Annex D; ISO 16017-1;[11] and Annex E). NOTE 2 For dry, homogeneous materials, results from tests of volatile organic emissions carried out using microscale chambers on newly manufactured products have been found to correlate well with data obtained using standard (reference) methods and conventional emission test chambers (ISO 12219-4, VDA 276[1] and ISO 16000-9 [6]) or test cells specified in this part of ISO 12219 is therefore complementary to existing standards. This part of ISO 12219 provides third party test laboratories and manufacturing industry with a cost-effective approach for: a) monitoring and screening VOC emissions as part of routine quality control; b) monitoring product uniformity or conformity between formal certification tests; c) comparing emissions from products within a range (e.g. different colours or patterns); d) evaluating prototype, “low-emission” materials or products during development. NOTE 3 All volatile carbonyl compounds except formaldehyde can be analysed according to ISO 16000-6.

Interior air of road vehicles - Part 3: Screening method for the determination of the emissions of volatile organic compounds from vehicle interior parts and materials - Micro-scale chamber method

ISO 12219-2:2012 公路车辆内空气.第2部分:汽车内饰和材料散发挥发性有机化合物的测定筛选法

This part of ISO 12219 specifies the sampling bag test method for measuring volatile organic compounds (VOCs), formaldehyde and other carbonyl compounds which may diffuse from vehicle interior parts into the air inside road vehicles. This method is intended for evaluating and screening new vehicle interior parts and materials such as seats, the instrument panel, ceiling materials and so on. The test method specified in this part of ISO 12219 specifies a procedure for screening of VOCs, formaldehyde and other carbonyl compounds using sampling bags. This part of ISO 12219 provides third party test laboratories and manufacturing industry with a cost-effective approach for: a) evaluating and screening prototype, “low-diffusion” materials or products during development; b) comparing diffusions from products within a range (e.g. different colours or patterns). This part of ISO 12219 specifies the design, construction, performance, evaluation, and use of sampling bags for testing vapour-phase organic emissions diffused from vehicle interior parts.

Interior air of road vehicles - Part 2: Screening method for the determination of the emissions of volatile organic compounds from vehicle interior parts and materials - Bag method

SAE J365-2012 内饰材料抗划伤测试方法

This test can be used to determine the resistance to scuffing of test specimens such as fiberboards, fabrics, vinyl-coated fabrics, leathers, and similar trim materials.

Method of Testing Resistance to Scuffing of Trim Materials

SAE J1568-2012 液压盘式制动器缸的塑料活塞材料

The materials defined by this SAE Standard are glass-fiber-reinforced, mineral-filled phenolic molding compounds suitable for compression molding. Performs may be radio frequency preheated or screw preheated slugs. Compound for use in hydraulic disc brake caliper pistons.

Materials for Plastic Pistons for Hydraulic Disc Brake Cylinders

SAE J1976-2012 外部材料的室外风化

This test method specifies the exposure racks, black boxes, and instrumentation, which shall be used for the outdoor weathering of materials for automotive exterior applications.

Outdoor Weathering of Exterior Materials

SAE J401-2012 钢的选定和使用

The SAE system of designating steels, described in SAE J402, classifies and numbers them according to chemical composition. In the case of the dent resistant, high strength and ultra high strength steels in SAE J1442 and the high strength carbon and alloy die drawn steels in SAE J935, minimum mechanical property requirements have been included in the designations. In addition, hardenability data on most of the alloy steels and some of the carbon steels will be found in SAE J1268.

Selection and Use of Steels

SAE J1523-2012 用于汽车型胶粘剂的金属对金属搭接剪切强度测试

This SAE Recommended Practice defines a procedure for determining shear strengths of adhesives used for bonding automotive oil metal substrates.

Metal to Metal Overlap Shear Strength Test for Automotive Type Adhesives

SAE J1325-2011 柔性绝缘材料相对悬垂性试验方法

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This SAE Recommended Practice describes a method of determining the relative flexibility of padding and/or acoustical composites. The purpose of this testing method is to establish a means for measuring the three-dimensional drapeability of flexible insulation materials, such as automotive floor pan insulation composites.

Test Method for Measuring the Relative Drapeability of flexible insulation Materials

SAE J413-2011 热处理锻钢的机械特性

The figures in this SAE Information Report illustrate the principle that, regardless of composition, steels of the same cross sectional hardness produced by tempering after through hardening, will have approximately the same longitudinal tensile strength at room temperature.

Mechanical Properties of Heat Treated Wrought Steels

SAE J948-2011 确定汽车车身布,乙烯和皮革,汽车车身布抽丝磨损耗力的测试方法

These methods of test are applicable for determining the resistance to snagging and abrasion of automotive bodycloth, vinyl and leather.

Test Method for Determining Resistance to Abrasion of Automotive Bodycloth, Vinyl, and Leather, and the Snagging of Automotive Bodycloth