共找到 313 条与 承载系统 相关的标准,共 21 页
1.1 This test method determines the extent to which a test grease retards the rotation of a specially-manufactured, spring-loaded, automotive-type wheel bearing assembly when subjected to low temperatures. Torque values, calculated from restraining-force determinations, are a measure of the viscous resistance of the grease. This test method was developed with greases giving torques of less than 35 N183;m at 40176;C.1.2 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Test Method for Low-Temperature Torque of Grease-Lubricated Wheel Bearings
This notice should be filed in front of MS14119(AS), dated 6 January 1972.
FLANGE, AIR TURBINE STARTER MOUNTING
This notice should be filed in front of MIL-R-l9445A(AER), dated 1 September 1959.
RACK, BOMB, AERO 65A SERIES
Road vehicles leaf springs - Requirements, testing
This part of ISO 3739 specifies the main require-ments, including size designation and marking, of 5° tapered and flat base rims with diameters not ex-ceeding rim diameter code 15 for pneumatic tyres, and for solid tyres for pneumatic tyre rims, primarily intended for industrial vehicles for use on prepared surfaces. ISO 3739-1 gives the designation, dimensions and marking, and ISO 3739-2 the load ratings of pneu-matic tyres (metric series). ISO 10499 covers the designation, dimensions and marking of rubber solid tyres (metric series) for pneumatic tyre rims. Rim dimensions are specified for size and contour only. The tyre and the wheel/rim manufacturers have to be consulted for confirmation of the suitability of the tyre/rim combinations, particularly with regard to rim profile and wheel strength.
Tyres and wheels - Rim profiles and dimensions - Industrial vehicle rims - Specification for rim profiles and dimensions for metric series pneumatic tyres and solid tyres for pneumatic tyre rims
The document lays down only those rim contour dimensions necessary for tyre mounting, and for fitting the tyre to the rim.#,,#
5° tapered rims for trucks, buses and trailers - Rim-diameter-code 15, 20 and 24
Two-piece divided rims for industrial vehicles -- Fastening dimensions
本标准规定了汽车、摩托车用软轴的结构及安装件尺寸、技术要求、试验方法、检验规则、标志、包装、运输及贮存。 本标准适用于汽车、摩托车用车速里程表或转速表用软轴。
Flexible shafts for automobiles and motorcycles
Test methods for light alloy wheels of motorcycles and mopeds
General specifications for aluminum alloy integral wheels of motorcycles and mopeds
Road vehicles. Roof load carrier devices. Part 1 : roof bars.
Passenger cars - Light alloy wheels - Impact test
This notice should be filed in front of MIL-R-38953C dated 8 October 1976.
RACK, BOMB EJECTOR, AIRCRAFT MAU-12B/A AND RACK, BOMB EJECTOR, AIRCRAFT MAU-12C/A
MIL-R38957C, dated 19 October 1976, is inactive for new design and is no longer to be used except for replacement purposes
RACK, BOMB EJECTOR, AIRCRAFT MAU-40/A
This notice should be fled in fiont of MIL-R-38956C dated 19 October 1976.
RACK, BOMB EJECTOR, AIRCRAFT MAU-50/A
Variable Section Leaf Springs for Mini Trucks
This Subsection of BS AU 50 : Part 4 specifies contours and dimensions of rims for use with code-designated series tyres used on industrial vehicles. Requirements for such tyres are specified in BS AU 50 : Part 1 : Subsection 5.1 : 1994. Requirements for rim construction and workmanship are specified in BS AU 50 : Part 2 : Section 0 : 1979. SAFETY NOTE. The wheel manufacturer should also be consulted to determine whether the rim and wheel is of sufficient strength for the intended service. In particular, care should be taken to ensure that the wheel will withstand the maximum pressure of any tyre that can be fitted in accordance with BS AU 50 : Part 1 : Subsection 5.1 : 1994. This pressure may exceed 1000 kPa (10 bar) for both diagonal and radial tyres.
Tyres and wheels - Rim profiles and dimensions - Industrial vehicle rims - Specification for rim profiles and dimensions for code-designated series tyres
Commercial vehicles - Wheel hub attachment dimensions
This notice should be filed in front of MIL-S-62076B(AT), dated 26 February 1982.
SEMITRAILER, CHASSIS: INTERMODAL CARGO CONTAINER CARRYING, COMMERCIAL AND CONTAINER, CARGO: INTERMODAL, DEMOUNTABLE, COMMERCIAL
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号