T22 承载系统 标准查询与下载
共找到 313 条与 承载系统 相关的标准，共 21 页
This International Standard defines criteria that characterize geometrical uniformity of wheels and describes principles of measurements of these criteria.
Road vehicles - Wheels - Measurement of radial and lateral run-out
- ICS
- 43.040.50
- CCS
- T22
- 发布
- 2006-02
- 实施
This SAE Recommended Practice is intended to serve as a guide for standardization of features, dimensions, and configurations of balance weights and rim flanges for aluminum and steel wheels intended for use on passenger cars, light trucks, and multipurpose vehicles to assure good installation and retention of the balance weight on the rim flange. This document also provides test procedures and minimum performance requirements for testing balance weight retention. Alternate materials and geometries can be addressed in the future, for example adhesive balance weights.
Balance Weight and Rim Flange Design Specifications, Test Procedures, and Performance Recommendations
- ICS
- 43.040.50
- CCS
- T22
- 发布
- 2006-01-01
- 实施
- 2011-04-29
This International Standard specifies requirements for the use, and general maintenance and safety of wheels and rims, and defines their out-of-service conditions, such as cracked, worn and bent wheels. It is applicable to wheels intended for use on road vehicles as defined in ISO 3833, excepting mopeds and motorcycles, and including multi-piece wheels for trucks.
Road vehicles - Wheels and rims - Use, general maintenance and safetyrequi rements and out-of-service conditions
- ICS
- 43.040.50
- CCS
- T22
- 发布
- 2005-12-05
- 实施
- 2005-12-05
Road vehicles - Wheels and rims - Use, general maintenance and safety requirements and out-of-service conditions.
- ICS
- 43.040.50
- CCS
- T22
- 发布
- 2005-09-01
- 实施
- 2005-09-05
This International Standard specifies a laboratory test procedure to evaluate the axial (lateral) kerb impact collision properties of a wheel manufactured either wholly or partly of light alloys. It is intended for passenger car applications, and special vehicle applications where the wheel may impact the kerb, with the purpose of screening and/or quality control of the wheel. The vocabulary used is in accordance with ISO 3911.
Road vehicles - Light alloy wheels - Impact test
- ICS
- 43.040.50
- CCS
- T22
- 发布
- 2005-08-26
- 实施
- 2005-08-26
This International Standard specifies a test method to evaluate the strength of the nut seat of wheels intended for use on passenger cars, light trucks and multi-purpose vehicles. While this test ensures the minimum strength of the nut seat, the wheel must also have a degree of flexibility to allow torque retention. This test evaluates the axial strength of the nut seat. In addition, the informative annex provides recommended bearing area to ensure enough strength for the rotational force in tightening a nut against the nut seat.
Road vehicles - Wheels - Nut seat strength tests
- ICS
- 43.040.50
- CCS
- T22
- 发布
- 2005-07
- 实施
This International Standard specifies a laboratory test procedure to evaluate the axial (lateral) kerb impact collision properties of a wheel manufactured either wholly or partly of light alloys. It is intended for passenger car applications, and special vehicle applications where the wheel may impact the kerb, with the purpose of screening and/or quality control of the wheel. The vocabulary used is in accordance with ISO 3911.
Road vehicles - Light alloy wheels - Impact test
- ICS
- 43.040.50
- CCS
- T22
- 发布
- 2005-07
- 实施
This International Standard specifies three laboratory methods for testing certain essential strength characteristics of disc wheels, spoke wheels and demountable rims intended for road use on commercial vehicles, buses, trailers and multipurpose passenger vehicles, as defined in ISO 3833. The test methods are a) disc wheel dynamic cornering fatigue test; b) disc wheels and wheels with demountable rims — dynamic radial fatigue test; and c) wheels with demountable rims — dynamic cornering fatigue test.
Road vehicles - Wheels/rims for commercial vehicles - Test methods
- ICS
- 43.040.50
- CCS
- T22
- 发布
- 2005-06-10
- 实施
- 2005-06-10
This International Standard specifies requirements for the use, and general maintenance and safety of wheels and rims, and defines their out-of-service conditions, such as cracked, worn and bent wheels. It is applicable to wheels intended for use on road vehicles as defined in ISO 3833, excepting mopeds and motorcycles, and including multi-piece wheels for trucks.
Road vehicles - Wheels and rims - Use, general maintenance and safety requirements and out-of-service conditions
- ICS
- 43.040.50
- CCS
- T22
- 发布
- 2005-06
- 实施
This SAE Recommended Practice provides minimum performance requirements and uniform procedures for fatigue testing of wheels intended for normal highway use on passenger cars, light trucks, and multipurpose passenger vehicles. For heavy truck wheels and wheels used as duals, see SAE J267. For wheels used on trailers drawn by passenger cars, light trucks, or multipurpose vehicles, see SAE J1204. these minimum performance requirements apply only to wheels made of materials included in Tables 1 to 4
Wheels Passenger Cars and Light Truck Performance Requirements and Test Procedures
- ICS
- 43.040.50
- CCS
- T22
- 发布
- 2005-02-02
- 实施
- 2016-03-22
This International Standard specifies two laboratory methods for testing certain essential fatigue strength characteristics of wheels intended for road use on passenger cars as defined in ISO 3833. The test methods are — dynamic cornering fatigue test; — dynamic radial fatigue test.
Road vehicles - Passenger car wheels for road use - Test methods
- ICS
- 43.040.50
- CCS
- T22
- 发布
- 2005-02
- 实施
This list has been prepared for use by or for the Government in the acquisition of products covered by Specification MIL-DTL-24308. Listing of a product is not intended to and does not connote endorsement of the product by the Department of Defense. All products listed herein have been qualified under the requirements for the product as specified in the latest effective issue of the applicable specification. This list is subject to change without notice; revision or amendment of this list will be issued as necessary. The listing of a product does not release the supplier from compliance with the specification requirements.
CONNECTORS, ELECTRIC, RECTANGULAR, NONENVIRONMENTAL, MINIATURE, POLARIZED SHELL, RACK AND PANEL, GENERAL SPECIFICATION FOR
- ICS
- 43.040.60
- CCS
- T22
- 发布
- 2005
- 实施
The International Standard Recording Code (ISRC) may be applied to audio recordings and music video recordings regardless of whether they are in analogue or digital formats. The ISRC shall not be used for the numbering of audio or audiovisual carriers (e.g. compact discs or videocassettes).
Wheels and rims for pneumatic tyres - Vocabulary, designation and marking
- ICS
- 01.040.43;43.040.50
- CCS
- T22
- 发布
- 2004-12-06
- 实施
- 2004-12-06
This International Standard presents a vocabulary of terms related to, and systems for the designation and marking of, wheels and rims intended for use with pneumatic tyres. The intention is to define fundamental wheel and rim terms rather than provide a comprehensive tabulation of all wheel design features. Also specified are the content, location and minimum size of the wheel and rim marking, with the purpose of establishing, on a worldwide basis, a uniform identification system for wheels and rims. NOTE 1 In addition to terms in English and French (two of the three official ISO languages), this International Standard gives the equivalent terms in German; these are published under the responsibility of the member bodies for Germany (DIN). However, only the terms and definitions given in the official languages can be considered as ISO terms and definitions. See Annex C.
Wheels and rims for pneumatic tyres - Vocabulary, designation and marking
- ICS
- 01.040.43;43.040.50
- CCS
- T22
- 发布
- 2004-11
- 实施
本标准规定了汽车车轮跳动量的要求和检测方法。 本标准适用轮辋规格为5°DC、SDC、FB和15°DC的汽车车轮。
Run out requirements and measuring methods of automotive wheels
- ICS
- CCS
- T22
- 发布
- 2004-10-20
- 实施
- 2005-04-01
本标准规定了汽车车轮安装面平面度要求和检验方法。 本标准适用于所有汽车车轮。
Performance requirements and test methods of automobile wheel's disc base planeness
- ICS
- CCS
- T22
- 发布
- 2004-10-20
- 实施
- 2005-04-01
This list has been prepared for use by or for the Government in the acquisition of products covered by subject specification and such listing of a product is not intended to and does not connote endorsement of the product by the Department of Defense.
CONNECTORS, ELECTRICAL, MINIATURE, RACK AND PANEL, ENVIRONMENT RESISTING, 200 DEG. C AMBIENT TEMPERATURE, GENERAL SPECIFICATION FOR
- ICS
- 43.040.60
- CCS
- T22
- 发布
- 2004
- 实施
This SAE Recommended Practice establishes minimum performance requirements and related uniform laboratory test procedures for evaluating axial (lateral) curb impact collision properties of all wheels intended for use on passenger cars and light trucks. It is equivalent to ISO 7141-1981 with the excpetion of the definitions section which cites SAE J393.
Wheels Impact Test Procedures Road Vehicles
- ICS
- 43.040.50
- CCS
- T22
- 发布
- 2003-09-01
- 实施
This SAE practice is intended for the sample preparation of test pieces for automotive wheels and wheel trim. The practice provides a consistent scribing method for use on test panels and or component parts with substrate chemical pretreatment and coating systems. Test specimens can then be subjected to various corrosion tests in order to evaluate performance without significant variations of the degree of exposure of the substrate. The scribing is used to create a break in the coating/finishing as can occur in the field through gravel and other damaging conditions.
Scribing of Coatings in Preparation for Testing of Wheels and Wheel Trim
- ICS
- 43.040.50
- CCS
- T22
- 发布
- 2003-01-01
- 实施
- 2015-03-21
This test method differentiates among greases having distinctly different low-temperature characteristics. This test is used for specification purposes and correlates with its precursor which has been used to predict the performance of greases in automotive wheel bearings in low-temperature service.4 It is the responsibility of the user to determine the correlation with other types of service.1.1 This test method determines the extent to which a test grease retards the rotation of a specially-manufactured, spring-loaded, automotive-type wheel bearing assembly when subjected to low temperatures. Torque values, calculated from restraining-force determinations, are a measure of the viscous resistance of the grease. This test method was developed with greases giving torques of less than 35 Nm at -40176;C.1.2 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Test Method for Low-Temperature Torque of Grease-Lubricated Wheel Bearings
- ICS
- 75.100 (Lubricants, industrial oils and related pr
- CCS
- T22
- 发布
- 2003
- 实施
