T23 转向与操纵系统 标准查询与下载
共找到 134 条与 转向与操纵系统 相关的标准，共 9 页
本标准规定了汽车真空助力器总成的性能要求、试验方法、检验规则及产品的标志、包装、运输和贮存。 本标准适用于汽车真空助力器。
Vacuum booster technical conditions
- ICS
- CCS
- T23
- 发布
- 1999-08-09
- 实施
- 2000-01-01
The purpose of this SAE Recommended Practice is to present design recommendations for the direction-of-motion of hand controls found in passenger vehicles, multipurpose vehicles, and trucks. These recommendations are based on recent and past human factors research and are important considerations in the design of control layouts. This document supersedes Figure 1 of SAE J1139.(9)
Direction-of-Motion Stereotypes for Automotive Hand Controls
- ICS
- 43.040.60
- CCS
- T23
- 发布
- 1999-07-01
- 实施
本标准适用于汽车接头式转向横、直拉杆总成，也适用于整体式转向直拉杆总成。
Automobile steering tie rod assembly technical conditions
- ICS
- CCS
- T23
- 发布
- 1999-03-15
- 实施
- 1999-03-15
本标准规定了汽车用液力变矩器通用技术要求、检验规则及对标志、包装、运输、贮存的要求。 本标准适用于轿车、客车、载货汽车、越野汽车和专用汽车用液力变矩器，汽车用液力机械变矩器也可参照执行。
Specifications for hydraulic torque converters for automobiles
- ICS
- CCS
- T23
- 发布
- 1999
- 实施
- 1999-03-15
本标准适用于汽车液压转向加力装置中独立的转向动力缸和转向加力器里的动力缸部分。
Automobile power steering power cylinder specification
- ICS
- CCS
- T23
- 发布
- 1999
- 实施
- 1999-03-15
本标准适用于汽车液压转向加力装置中独立的转向动力缸和转向助力器里的动力缸部分。
Automobile power steering power cylinder bench test method
- ICS
- CCS
- T23
- 发布
- 1999
- 实施
- 1999-03-15
本标准适用于汽车液压转向加力装置中的转向油罐。
Specifications for automotive power steering oil tanks
- ICS
- CCS
- T23
- 发布
- 1999
- 实施
- 1999-03-15
本标准规定了汽车常流式液压动力转向控制阀总成台架试验方法。 本标准适用于单独的控制阀总成，也适用于与有关部件装成一体的控制阀，例如控制阀与动力缸一体的联阀式动力转向装置中的控制阀，控制阀与转向器一体的半整体式动力转向装置中的控制阀和控制阀与转向器及动力缸一体的政体式动力转向装置中的控制阀。
Automobile power steering control valve assembly bench test method
- ICS
- CCS
- T23
- 发布
- 1999
- 实施
- 1999-03-15
本标准规定了汽车转向拉杆接头总成的摆动力矩测定、旋转力矩测定、最大轴向位移量测定及耐久性试验等台架试验方法。 本标准适用于汽车转向拉杆接头总成。出厂试验与型式试验的项目与要求由相应的技术条件规定。
Automobile steering rod joint assembly bench test method
- ICS
- CCS
- T23
- 发布
- 1999
- 实施
- 1999-03-15
本标准规定了汽车操纵稳定性指标限值与评价方法。 本标准适用于在公路、城市道路上行驶的汽车，非公路上行驶的汽车可参照执行。
Limits and Evaluation Methods of Automobile Handling Stability Index
- ICS
- CCS
- T23
- 发布
- 1999
- 实施
本标准规定了转向盘试验方法，适用于金属骨架包覆塑料的汽车、拖拉机用转向盘。
Automobile steering wheel test method
- ICS
- CCS
- T23
- 发布
- 1999
- 实施
本标准规定了汽车常流式动力转向控制阀总成的技术要求、试验方法、标志与包装。 本标准适用于汽车常流式动力转向控制阀总成。
Specifications for automobile power steering control valve assembly
- ICS
- CCS
- T23
- 发布
- 1999
- 实施
- 1999-03-15
この規格は，自動車のアクセル，ブレーキ及びクラッチペダルの配置及びペダル類の配置の測定方法について規定する。
Automobiles -- Lateral spacing of foot controls
- ICS
- 43.040.01
- CCS
- T23
- 发布
- 1998-07-20
- 实施
Video "Playground safety
Public transport. Road vehicles. Driver's console mechanical interface requirements. Minimum display and keypad parameters
- ICS
- 45.060.01;43.080.20
- CCS
- T23
- 发布
- 1998-07-15
- 实施
- 1998-07-15
This specification covers hose fabricated from wire braid and synthetic rubber, assembled with end fittings for use in automotive applications up to 10.3 MPa (1500 psi) maximum pressure, as flexible connections within the temperature range of -40 ?C to 121 ?C (-40 ?F to +250 ?F) average, 13.5 ?C (275 ?F) maximum peaks. The specification in this SAE Standard originated in the SAE-ASTM Technical Committee on Automotive Rubber (other than tires). They represent the correlation of the best information available from research investigation and production experience on the minimum constructional and performance characteristics essential for new power steering assemblies used as original or replacement equipment. This standard applies to passenger cars. It may prove useful to truck manufacturers, but it is not to be presented as present practices. They also represent the minimum quality recognized by original equipment manufacturers and hose suppliers as essential for satisfactory and safe operation by the hose itself and other coacting parts of the power steering system. The original equipment manufacturer may, at his option, add or alter tests through OEM specifications.
Power Steering Pressure Hose Wire Braid
- ICS
- 43.040.99
- CCS
- T23
- 发布
- 1998-05-01
- 实施
- 2007-08-10
本标准规定了汽车铝合金车轮的动态弯曲疲劳性能、动态径向疲劳性能要求及试验方法。 本标准适用于全部或部分轻合金制造的汽车车轮。
Performance requirements and test methods of light alloy wheels for automobiles
- ICS
- CCS
- T23
- 发布
- 1997-11-12
- 实施
- 1998-07-01
本标准规定了汽车用转向管柱上组合开关的技术要求、检验规则和试验方法等。 本标准适用于安装在汽车转向管柱上的组合开关。
Technical specification for combination switch on steering column for automobiles
- ICS
- CCS
- T23
- 发布
- 1996-12-18
- 实施
- 1997-09-01
This SAE Recommended Practice establishes consistent test procedures for determination of steady-state directional control properties for passenger cars and light trucks with single axles. These properties include the gradients with respect to lateral acceleration of steering wheel angle, understeer/oversteer, sideslip, roll angle, and steering wheel torque; the gains with respect to steering wheel angle of yaw velocity, lateral acceleration, and sideslip; the characteristic speed or critical speed; and the total, steering, and tire compliances at the front and rear wheels.
Steady-State Directional Control Test Procedures for Passenger Cars and Light Trucks
- ICS
- 43.020
- CCS
- T23
- 发布
- 1996-01-01
- 实施
- 2018-12-04
この規格は，自動車の盗難防止装置としてステアリングシャフトをキーにより 錠，開錠されるイグニションスイッチ付きステアリングロック(以下，ステアリングロックという。)について規定する。
Steering locks with ignition switches for automobiles
- ICS
- 43.040.10
- CCS
- T23
- 发布
- 1994-09-01
- 实施
