T32 螺塞、管件 标准查询与下载

SAE J2050-2012 高温动力方向盘压力软管

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This SAE Standard covers two types of hose fabricated from textile reinforcement and synthetic rubber, assembled with end fittings for use in high-temperature automotive power steering applications as flexible connections within the temperature range of -40 to +150 degrees C (-40 to +302 degrees F) maximum and 10.3 MPa (1500 psi) maximum working pressure. These hoses are intended for use in applications where reduction in amplitude of pump pressure pulsations is required. Class A hose has a nominal OD of 19.84 mm (0.781 in). Class B hose is a lightweight hose with a nominal OD of 17.91 mm (0.705 in). This specification defines the minimum performance levels of a flexible connector in the hydraulic steering system to convey power steering fluid from the steering pump to the steering gear.

High-Temperature Power Steering Pressure Hose

SAE J189-2012 动力转向回流软管低压

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This SAE Standard covers hose fabricated from fabric braid and synthetic rubber, assembled with end fittings or user applied clamps for use in automotive power steering applications as flexible connections within the temperature range of -40 degrees C to +120 degrees C (-40 degrees F to +250 degrees F) average, 135 degrees C (275 degrees F) maximum peaks. Hose assemblies shall be suitable for 1.72 MPa (250 psi) maximum working pressure with end fittings and 0.69 MPa (100 psi) maximum working pressure with user applied clamps.

Power Steering Return Hose Low Pressure

SAE J1290-2012 汽车液压制动系统公制管连接

This SAE Standard documents dimensional metric specifications for hydraulic brake system tubing with flared ends, threaded ports, and male tube nuts for the interconnection of major components in automotive hydraulic brake systems. The purpose of this document is to recommend preferred metrically dimensioned components (including alternative choices), that are intended to be functionally compatible with international Organization for Standardization Specification, ISO 4038-1977 (E). Some applications may require size of forms other than those shown herein, and this document does not preclude such other details when they are required.

Automotive Hydraulic Brake System Metric Tube Connections

SAE J617-2012 发动机飞轮壳和配套变速箱壳法兰

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This SAE Standard specifies the major dimensions and tolerances for Engine Flywheel Housings and the Mating transmission Housing Flanges. It also locates the crankshaft flange face or the transmission pilot bore (or pilot bearing bore) stop face in relation to housing SAE flange face. This document is not intended to cover the design of the flywheel housing face mating with the engine crankcase rear face of the design of housing walls and ribs. Housing strength analysis and the selection of housing materials are also excluded.

Engine Flywheel Housing and Mating Transmission Housing flanges

SAE J1405-2012 液压软管组件的选定试验规程

The procedures contained in this SAE Recommended Practice have been developed to establish uniform methods for impulse and high temperature circulation testing of hydraulic hose assemblies under special conditions not specified in SAE J 343 for SAE J 517 hoses. Basic test procedures are to be in accordance with SAE J 343 except as modified in this document.

Optional Test Procedures for Hydraulic Hose Assemblies

JIS D 2608:2012 汽车零件.使用非石油基液压制动流体的液压制动轮缸的橡胶套管

This Standard specifies moulded rubber boots used at end closures on automotive drum-type brake wheel cylinders using a non-petroleum-base brake fluid to prevent the entrance of dirt and moisture into the cylinder (hereafter referred to as "boots").

Automotive parts.Rubber boots for hydraulic brake wheel cylinders using a non-petroleum base hydraulic brake fluid

SAE J30-2012 燃料软管和油软管

This SAE standard covers fuel, oil, or emission hose for use in coupled and uncoupled applications, for use with gasoline, oil, diesel fuel, lubrication oil, or the vapors present in either the fuel system or in the crankcase of internal combustion engines in mobile or stationary applications. This standard covers the hose portion only. If assembly / coupling is required, that is to be agreed to between the customer and assembler, along with the specific requirements.

Fuel and Oil Hoses

SAE J1873-2012 水分转移试验程序,液压制动软管组件

This SAE Recommended Practice is intended for all vehicle hydraulic brake hoses. It is an accelerated test which is intended to the user with a method of comparing the ability of hydraulic brake hose designs to retard the ingress of moisture into brake fluid. This document specifies a laboratory performance requirement. ASTM D 1364 interlaboratory reproducibility and correlation of data have not been defined, nor has correlation been established between field vehicle brake fluid moisture content and data obtained by this document. The purpose of this recommended practice is to simulate in the laboratory the transmission of moisture into a brake hose.

Moisture Transmission Test Procedure Hydraulic Brake Hose Assemblies

SAE J514-2012 液压管道配件

This SAE Standard covers complete general and dimensional specifications for 37 degree flared and flareless types of hydraulic tube fittings and O-ring plugs. Also included are pipe fittings and adapter unions for use in conjunction with these tube fittings. These fittings are intended for general application in hydraulic systems on industrial equipment and commercial products. These fittings are capable of providing leak-proof, full flow connections in hydraulic systems operating at working pressures as specified in Table 1 for respective sections. Since many factors influence the pressure at which a hydraulic system will or will not perform satisfactorily, the values shown in SAE J1065 should not be construed as a guaranteed minimum. For any application, it is recommended that sufficient testing be conducted and reviewed by both the user and fitting manufacturer to assure performance levels will be safe and satisfactory.

Hydraulic Tube Fittings

SAE J343-2012 SAE 100R 系列液压软管和软管组件的测试和测试程序

This SAE Standard gives methods for the testing and evaluating performance of the SAE 100R series of hydraulic hose and hose assemblies (hose and attached end fittings) used in hydraulic fluid power systems. Specific tests and performance criteria for evaluating hose assemblies used in hydraulic service are in accordance with the requirements for hose in the respective specifications of SAE J 517. This document further establishes a uniform means of testing and evaluating performance of hydraulic hose assemblies.

Test and Test Procedures for SAE 100R Series Hydraulic Hose and Hose Assemblies

SAE J2196-2011 汽车空调维修软管

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This SAE Standard covers reinforced rubber, reinforced thermoplastic, or otherwise constructed hose, or hose assemblies, intended for conducting liquid and gaseous refrigerants for service connections from mobile air conditioning systems to service equipment such as a manifold gauge set and vacuum pumps or for use internally, in charging stations or service equipment intended for use in servicing mobile air-conditioning systems. The hose shall be designed to minimize permeation of refrigerants and contamination of refrigerant passing there through and to be serviceable over a temperature range of -30 to 95 degrees C. Hose working pressures shall be at least 3.4 MPa and the minimun burst pressure shall be at least 5 times.

Service Hose for Automotive Air Conditioning

SAE J2631-2011 液压油与液压软管合成橡胶的兼容性测定

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This SAE Information Report is intended to provide the hydraulic oil manufacturer and hydraulic equipment manufacturer with information that can be used predicting the relative impact that non petroleum based hydraulic oils may have on the hose elastomers in the existing system. This document contains the information necessary to perform the tests using standard elastomer formulations, representative of material used in hydraulic hose. The test methods used are defined within ASTM D471, standard test method for Rubber Property-Effect of Liquids. The physical properties measured, are volume swell, tensile strength, percent elongation, shore A hardness and load at 100% elongation. The properties were measured, after immersion, at 72 hours, 168 hours, 336 hours, 504 hours, 672 hours, 840 hours, and 1008 hours and the percent calculated as change from the unaged properties. The detail of the testing process is described in the following report.

Defining Hydraulic Oil Compatibility with Hydraulic Hose Elastomers

SAE J516-2011 液压软管配件

This SAE Standard provides general and dimensional specifications for the most common hose fittings used in conjunction with hydraulic hoses specified in SAE J517 and utilized in hydraulic systems on mobile and stationary equipment. The general specifications contained in Sections 1 through 15 are applicable to all hydraulic hose fittings and supplement the detailed specifications for the 100R-series fittings contained in the later sections of this document. This document shall be utilized as a procurement document only to the extent agreed upon by the manufacturer and user. Refer to SAE J517 for specifications of hose and information on hose assemblies. SAE J1273 contains information on application factors affecting hose fittings, hose, and hose assemblies. THE RATED WORKING PRESSURE OF A HOSE ASSEMBLY COMPRISING SAE J516 FITTINGS AND SAE J517 HOSE SHALL NOT EXCEED THE LOWER OF THE TWO WORKING PRESSURE RATED VALUES.

Hydraulic Hose Fittings

SAE J2197-2011 HFC-134a(R-134a)汽车空气调节维护设备用维护软管配件

This SAE Standard covers fittings intended for connecting service hoses, per SAE J2196, from Mobile Air-Conditioning Systems to service equipment such as manifold gauges, vacuum pumps and air-conditioning charging, recovery and recycling equipment.

HFC-134a (R-134a) Service Hose Fittings for Automotive air-Conditioning Service Equipment

SAE J2879-2011 汽车液压制动管接头

This document applies to 90 degree double inverted flares use don common sizes of automotive hydraulic brake tubes, and their associated tube nuts and mating ports. The intent of this standard is to replace the use of SAE J 512 and SAE J 533 for automotive hydraulic brake tube connections.

Automotive Hydraulic Brake Tube Joints

SAE J835-2011 分体式套管的设计与应用

This SAE Standard presents the standard sizes, important dimensions, specialized measurement techniques and tolerances for split type bushings. Both SI and inch sizes are shown; their dimensions are not exact equivalents. New designs shall use SI units. Unless specifically stated as ±, all tolerances are total.

Split Type Bushings Design and Application

SAE J1231-2011 软管连接和软管接头的形成管两端

This SAE Standard provides general and dimensional specifications for formed tube ends and hose fittings. These connections are intended for general applications in low pressure automotive and hydraulic systems on automotive, industrial, and commercial products. The fittings shown are intended to be retained by hose clamps as specified in SAE J1508. It is recommended that where step sizes or additional types of fittings are required, they be designed to conform with the specifications of this document insofar as they may apply. The following general specifications shall supplement the dimensional data contained in the tables with respect to all unspecified detail.

Formed Tube Ends for Hose Connections and Hose Fittings

SAE J2495-2011 套管材料的热密封效率

This SAE Standard measures the percent thermal efficiency of materials in sleeve form used to contain heat or insulate around a hot component. The percent thermal efficiency (%TE) is determined by measuring the power difference expended by the heat source (cartridge heater) with and without the test sleeve at the specified temperature. See SAE J2302 to measure radiant heat flow of sleeves.

Thermal Containment Efficiency of Sleeve Materials (Stabilized Type)

NF R19-501-7:2011 道路车辆.液压管路部件清洁度.第7部分:显微分析测量粒径和计数.

Road vehicles - Cleanliness of components of fluid circuits - Part 7 : particle sizing and counting by microscopic analysis.

NF R19-501-5:2011 道路车辆.液压管路部件清洁度.第5部分:在功能试验台上萃取污染物的方法.

Road vehicles - Cleanliness of components of fluid circuits - Part 5 : method of extraction of contaminants on functional test bench.