T38 照明与信号设备 标准查询与下载

SAE USCAR34-2009 试验性车灯装配规范

Specification for testing automotive lamp assemblies

SAE J914-2009 长度小于12 m的车辆用侧转向灯

This SAE Standard provides installation requirements, test procedures, design guidelines, and performance requirements for side turn signal lamps for vehicles less than 12 m in length.

Side Turn Signal Lamps for Vehicles Less Than 12 m in Length

NF R13-629/A4:2009 陆地起床灯.尺寸,电力和照明要求

Lamps for road vehicles - Dimensional, electrical and luminous requirements.

SAE J2121-2009 施工和供工业机械中的组合照明装配的要求

This SAE Standard provides general design performance requirements and related test procedures for composite lighting unit assemblies, other than signaling and marking devices, used on Earthmoving, Agricultural Tractors, and Road Building and Maintenance off-road work machines as defined in SAE J1116. To provide general guidelines and design parameters for lighting assemblies used on construction and industrial machinery.

Requirements for Composite Lighting Assemblies Used on Construction and Industrial Machinery

SANS 20048:2009 与照明及光信号设备安装相关车辆的许可有关的统一规定

Applies to vehicles of categories M, N, and to their trailers (category O) with regard to the installation of lighting and light-signalling devices.

Uniform provisions concerning the approval of vehicles with regard to the installation of lighting and light-signalling devices

DIN EN 60810:2009 道路车辆用灯 性能要求

Lamps for road vehicles - Performance requirements (IEC 60810:2003 + A1:2008); German version EN 60810:2003 + A1:2008

SAE J852-2009 用于机动车辆的前拐弯灯

This SAE Recommended Practice provides test procedures, performance requirements, and guidelines for front cornering lamps intended for use on motor vehicles.

Front Cornering Lamps for Use on Motor Vehicles

SAE J592-2009 全宽小于2032mm的道路车辆用边侧标志灯

This SAE Standard provides test procedures, requirements, and guidelines for sidemarker lamps for vehicles less than 2032 mm in overall width.

Sidemarker Lamps for Use on Road Vehicles Less Than 2032 mm in Overall Width

SAE HS-34-2009 SAE地面车辆照明标准手册2009年版

The SAE Ground Vehicle Lighting Manual provides a comprehensive compilation of SAE Technical Reports relating to the design, engineering, testing, inspection and installation of motor vehicle lighting and signalling equipment. The basic standards and recommended practices in the Manual are those developed under the auspices of the SAE Lighting Committee.

SAE Ground Vehicle Lighting Standards Manual 2009 Edition

NF R13-630/A1:2009 道路车辆用灯.性能要求

Lamps for road vehicles - Performance requirements.

SAE J595-2008 认可的应急、维护和服务车辆用定向闪烁光学警告装置

This document provides design guidelines, test procedure references, and performance requirements for directional, single color, flashing optical warning devices used on authorized emergency, maintenance, and service vehicles. It is intended to apply to, but not limited to, surface land vehicles.

Directional Flashing Optical Warning Devices for Authorized Emergency, Maintenance, and Service Vehicles

SAE J1424-2008 5443kg(12000 lb)GVWR载荷下车辆使用的货物照明灯

This SAE Recommended Practice provides test procedures, performance requirements, design guidelines, and installation requirements for cargo lamps that are mounted on the exterior of vehicles weighing under 5443 kg (12000) lb GVWR.

Cargo Lamps for Use on Vehicles Under 5443 kg (12 000 lb) GVWR

SAE J2591-2008 用于前进的照明设备

This SAE Recommended Practice applies to motor vehicle Forward Illumination Devices which incorporate adaptive beam pattern capabilities. This document is to be used in conjunction with other forward lighting standards and/or recommended practices which define the base beam procedures, requirements, and guidelines.

Adaptive Forward Lighting System

IEC 60810:2008 道路车辆用灯.性能要求

This International Standard is applicable to replaceable lamps (filament lamps and discharge lamps) to be used in headlamps, fog-lamps and signalling lamps for road vehicles. It is especially applicable to those lamps which are listed in IEC 60809. However, the standard may also be used for other lamps falling under the scope of this standard, as well as for future developments, e.g. such where the light is produced by light emitting diodes (LED). It specifies requirements and test methods for the measurement of performance charac- teristics such as lamp life, lumen maintenance, torsion strength, glass bulb strength and resistance to vibration and shock. Moreover, information on temperature limits, maximum lamp outlines and maximum tolerable voltage surges is given for the guidance of lighting and electrical equipment design. For some of the requirements given in this standard, reference is made to data given in tables. For lamps not listed in such tables, the relevant data are supplied by the lamp manufacturer or responsible vendor. The performance requirements are additional to the basic requirements specified in IEC 60809. They are, however, not intended to be used by authorities for legal type-approval purposes. NOTE In the various vocabularies and standards, different terms are used for "incandescent lamp" (IEV 845-07-04) and "discharge lamp" (IEV 845-07-17). In this standard, "filament lamp" and "discharge lamp" are used. However, where only "lamp" is written both types are meant, unless the context clearly shows that it applies to one type only.

Lamps for road vehicles - Performance requirements

SAE J2042-2008 整体宽度为2032 mm或更长的机动车用限界灯、旁侧示廓灯和标志灯

This SAE Standard provides test procedures, requirements, and guidelines for clearance, sidemarker, and identification lamps intended for use on vehicles 2032 mm or more in overall width. A clearance lamp, sidemarker lamp, or an identification lamp conforming to the requirements of this document may be used on vehicles less than 2032 mm in overall width.

Clearance, Sidemarker, and Identification Lamps for Use on Motor Vehicles 2032 mm or More in Overall Width

IEC 60810:2003/AMD1:2008 道路车辆用灯.性能要求

This amendment has been prepared by subcommittee 34A: Lamps, of IEC technical committee 34: Lamps and related equipment. The text of this amendment is based on the following documents: Full information on the voting for the approval of this amendment can be found in the report on voting indicated in the above table. The committee has decided that the contents of this amendment and the base publication will remain unchanged until the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in the data related to the specific publication. At this date, the publication will be ~ reconfirmed, ~ withdrawn, ~ replaced by a revised edition, or ~ amended.

Lamps for road vehicles - Performance requirements

SAE J588-2008 全部宽度小于2032 mm的汽车用方向灯

This SAE Standard provides test procedures, requirements, and guidelines for turn signal lamps intended for use onvehicles of less than 2032 mm in overall width.

Turn Signal Lamps for Use on Motor Vehicles Less Than 2032 mm in Overall Width

JIS C 7506-3:2008 道路车辆用灯.第3部分:指示灯

This Standard specifies requirements related to the life,torsion strength and basic requriements(dimensional,electrial and luminous) of miniature lamps(hereafter referred ro as "lamps") for use in road vehicles not included in JIS C7506-1.

Lamps for road vehicles -- Part 3: Miniature lamps

JIS C 7506-1:2008 道路车辆用灯.第1部分:尺寸、电和照明要求

この規格は，自動車用へッドランスフオグランプなどの照明灯及び信号灯に使われる交換可能な白熱電球及びハロゲン電球(以下，電球という。)並びにディスチャージランプを対象とし，試験方法及ぴ基本的互換生（寸法.電気及び光学)の要求事項について規定する。

Lamps for road vehicles -- Part 1: Dimensional, electrical and luminous requirements

JIS C 7506-2:2008 道路车辆用灯.第2部分:性能要求

この規格は，自動車用へッドランプ，フオグランプなどの照明灯及び信号灯に使われる交換可能な白熱電球及びハロゲン可球(以下，電球という。)並びにディスチャージランプを対象とし.ロ金接着強さ，寿命，光東維持率.耐振性.ガラス球強度，ガラス球変位及びこれらの試験方法について規定する。さらに，灯具設計のガイダンスとして与えられる温度限界.最大サージ篭圧及び電球の最大外郭寸法の情報について記載する。

Lamps for road vehicles -- Part 2: Performance requirements