T38 照明与信号设备 标准查询与下载

SANS 1376-1:2008 机动车辆用灯具.第1部分:白炽灯

Covers incandescent tungsten filament lamps of categories R2, H1, H2, H3, H4, P21W, P21/5W, R5W, R10W, C5W, C18W, C21W, T4W, W3W and W5W for use in motor vehicles and trailers. Also covers other categories of lamp that are covered in SANS 20037.

Lights for motor vehicles Part 1: Incandescent lamps

SANS 20119:2008 与电动车辆的角灯许可相关的统一规定

Applies to cornering lamps for vehicles of categories M, N and T.

Uniform provisions concerning the approval of cornering lamps for power-driven vehicles

SAE J1849-2008 应急车辆警报器

This SAE Recommended Practice provides laboratory test procedures, requirements and guidelines for electronic siren systems with a single loudspeaker, and electromechanical sirens for use on authorized emergency vehicles, which call for the right-of-way. Test procedures and performance requirements for individual system components are not included in this version. Results obtained for a siren system with a speaker array that is greater than 0.5 m in any dimension shall apply to the system only when the array is in the same spatial configuration as tested (i.e., the same speaker separation and orientation.)

Emergency Vehicle Sirens

SAE J585-2008 总体宽度小于2032mm的机动车辆用尾灯(后位灯)

This SAE Standard provides test procedures, requirements, and guidelines for tail lamps (rear position lamps) intended for use on vehicles of less than 2032 mm in overall width.

Tail Lamps (Rear Position Lamps) for Use on Motor Vehicles Less Than 2032 mm in Overall Width

SANS 20020:2008 与发射不对称近光或远光或同时发射两种光以及装备有卤素灯(H4灯)的电动车辆前灯(SB)许可有关的统一规定

Applies to motor vehicle headlamps which may incorporate lenses of glass or plastic material.

Uniform provisions concerning the approval of motor vehicle headlamps emitting an asymmetrical passing beam or a driving beam or both and equipped with halogen filament lamps (H4 lamps)

GOST R 53074-2008 高压汞汽灯.性能要求

High-pressure mercury vapour lamps. Performance requirements

SAE J377-2007 车辆交通听觉信号装置(喇叭)

This SAE Standard establishes the minimum operational life, environmental requirements, and sound level output for electrically driven Vehicular Traffic Sound Signalling Devices (hereinafter referred to as Horns) on new automotivevehicles. Test equipment, environment, and procedures are specified.1.1 Intended Usage and Life ExpectationThe horns meeting this specification are intended to be used on automotive vehicles, in defined climatic conditions and environments.Any device functioning as a horn, is intended to perform its function, to this specification for at least 10 years or 250 000 km (150 000 miles). Two levels of usage shall be defined: A – Normal Usage; and B – High Usage.For the purposes of this specification, Normal Usage (A) life shall be interpreted as:Nominal Duty—50 000 actuationsChirp Duty—40 000 actuationsLong Duty—200 actuationsContinuous Duty—4.0 minutes (per section 8.14)These duty cycles are defined in Appendix B (figure B1):For purposes of this specification, High Usage (B) life shall be interpreted as Normal Usage (A) followed by an additional 450 000 Nominal Duty Actuations.These duty definitions shall be modified for Combined Environment Testing as shown in the Combined Environment section.

Vehicular Traffic Sound Signaling Devices (Horns)

SANS 20065:2007 机动车特殊报警灯认证的统一规定

Applies to special warning lamps for vehicle category L, M, N, O, and T and for mobile machinery.

Uniform provisions concerning the approval of special warning lamps for power-driven vehicles and their trailers

SAE J586-2007 机动车辆用总宽度小于2032mm的刹车灯

This SAE Standard provides test procedures, requirements, and guidelines for stop lamps intended for use on vehicles of less than 2032 mm in overall width.

Stop Lamps for Use on Motor Vehicles Less Than 2032 mm in Overall Width

DLA MS35423 REV B VALID NOTICE 2-2007 结关服务指示灯

MS35423B, dated 05 September 2002, has been reviewed and determined to be valid for use in acquisition.

LIGHT, MARKER, CLEARANCE-SERVICE

DLA MS53047 REV A VALID NOTICE 3-2007 24 V服务信号和停电标记服务区灯

The activities above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http://assist.daps.dla.mil.

Light, Marker-Service Park, Service Signal and Blackout Marker, 24 Volt

SAE J575-2007 总体宽度小于2032mm的机动车辆用照明装置及元件的试验方法和设备

This SAE Recommended Practice provides standardized laboratory tests, test methods, and requirements applicable to many of the lighting devices and components covered by SAE Recommended Practices and Standards and is intended for reference for devices used on vehicles less than 2032 mm in width, regardless of length, or 7620 mm in length regardless of width. Tests for vehicles larger than 2032 mm in overall width are covered in J2139.

Test Methods and Equipment for Lighting Devices and Components for Use on Vehicles Less Than 2032 mm in Overall Width

SANS 20050:2007 关于批准L类汽车的前后位置灯，制动灯，转向信号灯和后牌照灯照明装置的统一规定

Applies to front position lamps, rear position lamps, stop lamps, direction indicators, and rear-registration-plate illuminating devices for vehicles of category L.

Uniform provisions concerning the approval of front position lamps, rear position lamps, stop lamps, direction indicators and rear-registration-plate illuminating devices for vehicles of category L

SANS 20091:2007 机动车及其挂车侧标志灯认证的统一规定

Applies to side-marker lamps for vehicles of category M, N, O and T.

Uniform provisions concerning the approval of side-marker lamps for motor vehicles and their trailers

SANS 20098:2007 装配气体放电光源的机动车前照灯认证的统一规定

Applies to motor vehicle headlamps and motor vehicle distributed lighting systems which may incorporate lenses of glass or plastic material, and which are equipped with gas-discharge light source(s) being fitted in the headlamp or in the remote light-gen

Uniform provisions concerning the approval of motor vehicle headlamps equipped with gas-discharge light sources

SANS 20007:2007 关于批准机动车（不含摩托车）及其挂车前后位置（侧边）灯，制动灯和示廓灯的统一规定

Applies to a) front and rear position (side) lamps and stop lamps for vehicles of categories L, M, N, O and T, and b) end-outline marker lamps for vehicles of categories M, N, O and T.

Uniform provisions concerning the approval of front and rear position (side) lamps, stop-lamps and end-outline marker lamps for power-driven vehicles and their trailers

SAE J95-2007 工业设备用前照灯

This SAE Standard provides performance and general design requirements and related test procedures for headlamps for use on industrial wheeled equipment that may be operated on public roads.

Headlamps for Industrial Equipment

SAE J1029-2007 建筑用土方机械的照明和标记

This SAE Standard establishes minimum requirements for lighting and marking earthmoving construction machinery as defined in SAE J1116, 1.1 Self- Propelled Construction Machines-Earthmoving (excluding excavators). (Construction machinery is normally operated off-highway, and therefore this SAE document is not intended to be used as a basis for regulations by those having authority over on-highway motor vehicles.)

Lighting and Marking of Construction, Earthmoving Machinery

SAE J222-2006 停车灯(前位灯)

This SAE Standard provides test procedures, requirements, and guidelines for parking lamps (front position lamps).

Parking Lamps (Front Position Lamps)

SAE J1735-2006 协调的车辆前照灯性能要求

This SAE Recommended Practice provides headlamp beam patter test points for harmonized low and high beam headlamp beam patterns that incorporate elements of European, Asian, and U.S. photometric tables. These photometric tables are optional to those found in SAE J 1383.

Harmonized Vehicle Headlamp Performance Requirements