T38 照明与信号设备 标准查询与下载

SAE J2584-2011 客车和小型敞篷货车的前灯安装高度

The Mounting Height Task Force was tasked to determine the extent of the problem(s) associated with vehicle headlamps mounted at or above the level of the mirror(s) in passenger vehicles; the level of glare exposure caused by high-mounted headlamps; the appropriate height differential needed to maintain a glare level consistent with past and/or current passenger vehicle headlamp mounting; and the necessary headlamp mounting height necessary to control mirror glare at an accepted/acceptable level. The report herein addresses these passenger vehicle mounting height issues.

Headlamp Mounting Height for Passenger and Pickup Truck Vehicles (Stabilized Type)

SAE J2282-2011 分布式照明系统(DLS)

This SAE Recommended Practice applies to motor vehicle distributed lighting systems (DLS) which use light generated by remote sources. It provides test methods, requirements, and guidelines applicable to these systems. This document is intended to be a guide to standard practice and is subject to change dependent upon additional experience and technical advances. This document covers Headlamp, Fog lamp, Auziliary lamp, plus Signal and Marking lamp functions.

Distributed Lighting Systems (DLS) (Stabilized Type)

SAE J581-2011 辅助远光灯

This SAE Standard provides test procedures, performance requirements and guidelines for auxiliary high beam lamps.

Auxiliary High Beam Lamps (Stabilized Type)

SAE J1606-2011 成年驾驶员前照灯设计指南

This SAE Information Report should be used as a supplement to SAE J1383. It is intended to provide additional information which is important to the automotive designer and engineer in the process of designing, developing, and engineering the headlamps of motor vehicles which will take into account the effects of the aging process on the driver.

Headlamp Design Guidelines for Mature Drivers (Stabilized Type)

SAE J591-2011 聚光灯

This SAE Standard provides test procedures and performance requirements for spot lamps.

Spot Lamps (Stabilized Type)

SAE J2087-2011 昼行灯

This SAE Recommended Practice provides test procedures, requirements, and guidelines for a daytime running light (DRL) function.

Daytime Running Light

SAE J584-2010 机动车前大灯

This SAE Standard provides design parameter and general requirements for motorcycle headlamps.

Motorcycle Headlamps

SAE J1373-2010 全长低于9.1 m的电动机车用后角灯

This SAE Recommended Practice provides test procedures, requirements, and guidelines for rear cornering lamps for use on vehicles less than 9.1 m in overall length.

Rear Cornering Lamps for Use on Motor Vehicles Less Than 9.1 m in Overall Length

SAE J593-2010 倒车灯(倒车灯)

This SAE Standard provides installation requirements, test procedures, design guidelines, and performance requirements for backup/reversing lamp.

Backup Lamp (Reversing Lamp)

SAE J1319-2010 后雾灯系统

This SAE Recommended Practice provides test procedures, requirements, and guidelines for fog tail lamp systems.

Rear Fog Lamp Systems

SAE J96-2010 工业设备用闪烁警示灯

This SAE Standard covers the general requirements and the test requirements for a flashing warning lamp for industrial wheeled equipment.

Flashing Warning Lamp for Industrial Equipment

SAE J1383-2010 机动车辆前照灯性能要求

This SAE Recommended Practice is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances. This document establishes performance requirements for headlamps.

Performance Requirements for Motor Vehicle Headlamps

SAE J1432-2010 总体宽度等于或超过2032mm的车辆中使用的背面高安装的停止灯和背面高安装的转弯信号灯

This SAE Recommeded Practice provides test procedures, requirements, and guidelines for high-mounted stop lamps and high-mounted turn signal lamps intended for use on vehicles 2032 mm or more in overall width. This document applies to trucks, motor coaches, van type trailers, and other vehicles with permanent structure greater than 2800 mm high. This document does not apply to school buses, truck tractors, pole trailers, flat-bed trailers, pick-up truck with dual wheels and trailer converter dollies. The purpose of the high-mounted stop lamp(s) and high-mounted turn signal lamp(s) is to provide a signal over intervening vehicles to the driver of following vehicles.

Rear High Mounted Stop Lamps and Rear High Mounted Turn Signal Lamps for Use on Vehicles 2032 mm or More in Overall Width

SAE J567-2010 照明电源固位系统

This SAE Standard references the performance and functional requirements of the International Electrotechnical Commission (IEC) and its U.S. member, the American National Standards Institute (ANSI). By referring to IEC/ANSI and its standards concerning light source (bulb) sockets, light source (lamp) holders, and gages, this document recognizes the need for harmonized standards world-wide for what are typically commodity items. Additional requirements are noted.

Lamp Source Retention System

SAE J2040-2010 总体宽度在2032mm和以上的车辆用尾灯(后位置尾灯)

This SAE Standard provides test procedures, requirements, and guidelines for tail lamps intended for use on vehicles 2032 mm or more in overall width. Tail lamps conforming to the requirements of this document may also be used on vehicles less than 2032 mm in overall width.

Tail Lamps (Rear Position Lamps) for Use on Vehicles 2032 mm or More in Overall Width

SAE J575-2010 总体宽度小于2032mm的机动车辆用照明装置及元件的试验方法和设备

This SAE Recommended Practice is intended as a quide toward standard practice and is subject to change to keep pace with experience and technical advances. This document provided standardized laboratory tests, test methods and equipment, and requirements for lighting devices used on vehicles less than 2032 mm in width. Tests for vehicles larger than 2032 mm in overall width are covered in J2139. Device specific tests and requirements can be found in applicable SAE technical reports.

Test Methods and Equipment for Lighting Devices for Use on Vehicles Less Than 2032 mm in Overall Width

SAE J594-2010 反射板

This SAE Standard provides test procedures, requirements, and guidelines for reflex reflectors.

Reflex Reflectors

SAE J2261-2010 总体宽度等于或大于2032 mm的机动车辆用刹车灯和前后转弯信号灯

This SAE Standard provides test procedures, requirements, and guidelines for stop lamps and turn signal lamps intended for use on vehicles 2032 mm or more in overall width. Stop lamps and front- and rear-turn signal lamps conforming to the requirements of this document may be used on vehicles less than 2032 mm in overall width.

Stop Lamps and Front- and Rear-Turn Signal Lamps for Use on Motor Vehicles 2032 mm or More in Overall Width

SAE USCAR3-2010 机动车小型灯泡的试验标准

The procedures contained in this specification cover the laboratory testing of miniature incandescent bulbs for use in automotive illumination and signaling applications. The following tests shall be run whenever the following occurs: New bulb design; Design or process change made to an existing bulb, which could affect the outcome of the test. The completion of one calendar year as noted in the following Test Schedule Table. Process control data is acceptable.

Standard for testing automotive miniature bulbs

DIN EN 60809:2009 道路车辆灯.尺寸,电气和亮度要求(IEC 60809:1995+A1:1996+A2:2002+A3:2004+A4:2009),德文版本EN 60809:1996+A1:1996+A2:2002+A3:2004+A4:2009

Lamps for road vehicles - Dimensional, electrical and luminous requirements (IEC 60809:1995 + A1:1996 + A2:2002 + A3:2004 + A4:2009); German version EN 60809:1996 + A1:1996 + A2:2002 + A3:2004 + A4:2009