共找到 322 条与 车用仪表及测试设备 相关的标准,共 22 页
Type of rubber Kvalitetsbeteckningar Quality designations
Resin, Impregnation, Heat-Cured Revision A
Freigabemuster, für die diese Vorschrift zutrifft, müssen nach dieser Vorschrift geprüft werden und von der Produktentwicklung und Konstruktion genehmigt sein
Resin, Impregnation, Heat-Cured Revision C
Freigabemuster, für die diese Vorschrift zutrifft, müssen nach dieser Vorschrift geprüft werden und von der Produktentwicklung und Konstruktion genehmigt sein
Resin, Impregnation, Heat-Cured Revision C
Nedanstaende forteckning tar upp material/ytbehandling som anvands i Saab personbilsproduktion, men som annu ej finns som faststalld standard.
Adhesive, Promoter, Barrier
Unbeschadet etwaiger durch den Abnehmer erfolgenden Stichprobenprufungen tragt der Lieferddie Verantwoflung dafür. da? die gelieferte flare die Opel-Zeichnungcvorschriften erfüllt.
Sealer - Pumpable, High Heat Resistant, Expandable Revision A
Materialet ar avsett for formblasta, glasklara, artiklar. The material is intended for blow moulded, crystal-clear,parts.
Preface
Materialet marks med 8772 plus aktuell tillstandssiffra. The material is to be marked with 8772 plus the relevant condition number.
Preface
Road vehicles. Sheath-type glow-plugs with conical seating and their cylinder head housing. Part 2 : M12 X 1,25 glow-plugs.
Road vehicles. Sheath-type glow-plugs with conical seating and their cylinder head housing. Part 1 : M14 X 1,25 glow-plugs.
For behandling av kontaktytor. For treatment of contact surfaces.
Lubricant, Clamp Assembly
8947 -2 For avtackning 8947 -2 As covering
Grease, Seal Lubricant, Brake System
Unbeschadet etwaiger durch den Abnehmer erfolgenden Stichprobenprüfungen tragt der Liefera ie Verantwortung dafür, da? die gelieferte Ware die Opel-Zeichnungsvorschriften erfüllt. Ein Prüfbericht mit zahlenma?igen Ergebnissen aus Prufungen der Lieferung
Nylon 6 - 33% Glass Fiber Reinforced, Heat Stabilized Revision B
-2 Materialet ar extra diffusionstatt och valt for att anvandas som spolarslang i kupen. Materialet har aven hog slagseghet i torrt tillstand samt god utmattningshallfasthet vid laga temperaturer. Beteckning enl ISO 1874 (DIN 16773): PA 6-HI, MHPR, 1
Adhesive, Structural, Sprayable Body Panel Reinforcement
This Standard applies to electronic taximeters, hereinafter referred to by the general term taxime-ters, to be installed on public hire vehicles (taxis or cabs) which, with the aid of electronic devices, calculate and indicate the amount to be paid by the passenger of the taxi. This standard does not apply to taximeters being remotely controlled by external intelligence as far as it concerns the functions described in this standard. This standard does not deal with performance requirements of the taximeter after installation or with the installation itself.
Electronic taximeters
The specified material requirements conform to those indicated in Swedish Standard SS 142172, issue 8, except for the conditions -20, -26 and -28 (which refer to pressure vessels).
Fluid, Cold Climate Power Steering Revision A
Materialet ar avsett for formsprutade artiklar. The material is intended for injection moulded parts.
Preface
Utgava 1 av denna standard utgavs som preliminar 1977-03-29.
Adhesion, Promoter, Rubber
Unbeschadet etwaiger durch den Abnehmer erfolgenden Stichprobenprüfungen tragt der Liefera #/ die Verantwortung dafür, daß die gelieferte Ware die Opel-Zeichnungsvorschriften erfüllt. Ein Prüfbericht mit zahlenmaßigen Ergebnissen aus Prüfungen der Liefer
Adhesive, Promoter, Foam Tape Revision B
Materialet ar avsett for greppytor The material is intended for grip surfaces
Adhesive, Two-Part, Urethane, Hardener
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号