轴系设备标准-分析测试百科网

JIS F 4803:1999 造船.船用螺旋桨.制造公差.第2部分:直径在0.8至2.5M之间含0.8M、2.5M的螺旋桨

この規格は，直径0.8m以上2.5m以下の船用プロペラの製作許容差について規定する。

Shipbuilding -- Ship screw propellers -- Manufacturing tolerances -- Part 2: Propellers of diameter between 0.80 and 2.50 m inclusive

ICS: 47.020.20
CCS: U48
发布: 1999-03-24
实施

KS V 7141-1998 舱墙用隔离片

? ??? ??? ?? ?? ?? ???? ???? ???? ??? ??? ????.

Distance pieces for ship's hull

ICS: 23.060.00
CCS: U48
发布: 1998-12-07
实施: 1998-12-07

NAVY MS19089 REV A NOTICE 1-1998 767(TNA)型可调整单双圆周陡角度双排滚筒锥形滚筒轴承

MS19089A, dated 13 January 1982, is inactive for new design and is no longer used, except for replacement purposes.

BEARING, ROLLER, TAPERED, DOUBLE ROW OF ROLLERS, STEEP ANGLE, TWO SINGLE CONES, ONE DOUBLE CUP, NON ADJUSTABLE, TYPE 767 (TNA)

ICS
CCS: U48
发布: 1998-04-22
实施

NAVY MS19088 REV A NOTICE 1-1998 764(TNA)型可调整单双圆周通用角度双排滚筒锥形滚筒轴承

MS19088A, dated 13 January 1982, is inactive for new design and is no longer used, except for replacement purposes.

BEARING, ROLLER, TAPERED, DOUBLE ROW OF ROLLERS, NORMAL ANGLE, TWO SINGLE CONES, ONE DOUBLE CUP, NON ADJUSTABLE, TYPE 764 (TNA)

ICS
CCS: U48
发布: 1998-04-22
实施

NAVY MS19087 REV A NOTICE 1-1998 763(TDOS)型可调整单双圆周陡角度双排滚筒锥形滚筒轴承

MS19087A, dated 13 January 1982, is inactive for new design and is no longer used, except for replacement purposes.

BEARING ROLLER, TAPERED DOUBLE ROW OF ROLLERS, STEEP ANGLE, TWO SINGLE CONES, ONE DOUBLE CUP, ADJUSTABLE, TYPE 763 (TDOS)

ICS
CCS: U48
发布: 1998-04-22
实施

ASTM F1309-98(2003) 船用机械基础制动器的安装程序的标准操作规程

This practice provides the three principal methods of fitting chocks to marine machinery foundations to ensure that the machinery is free of vibration and perfectly aligned after installation. 3.1.1 The three principal methods of installing chocks described herein are as follows: 3.1.1.1 Type A—Epoxy-based resin, nonshrinking Chockfast Orange PR 610 TCF by Philadelphia Resin Corp., or equal, and 3.1.1.2 Type B—Two-piece wedge chocks. 3.1.1.3 Type C—Solid, one-piece fitted chocks.1.1 This practice covers the acceptable methods of fitting chocks to marine machinery foundations.1.2 The values stated in SI units shall be regarded as standard. The values in parentheses are for information only.1.3 This standard does not purport to address the safety concerns associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Installation Procedures for Fitting Chocks to Marine Machinery Foundations

ICS: 47.020.20 (Marine engines and propulsion systems)
CCS: U48
发布: 1998
实施

ASTM F1309-98 船用机械基础制动器的安装程序

1.1 This practice covers the acceptable methods of fitting chocks to marine machinery foundations. 1.2 The values stated in SI units shall be regarded as standard. The values in parentheses are for information only. 1.3 This standard does not purport to address the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Installation Procedures for Fitting Chocks to Marine Machinery Foundations

ICS: 47.020.20 (Marine engines and propulsion systems)
CCS: U48
发布: 1998
实施

ASTM F1309-98(2007) 船用机械基座固定楔安装程序的标准实施规程

p>This practice provides the three principal methods of fitting chocks to marine machinery foundations to ensure that the machinery is free of vibration and perfectly aligned after installation. The three principal methods of installing chocks described herein are as follows: Type A—Epoxy-based resin, nonshrinking Chockfast Orange PR 610 TCF by Philadelphia Resin Corp., or equal, and Type B—Two-piece wedge chocks. Type C—Solid, one-piece fitted chocks.1.1 This practice covers the acceptable methods of fitting chocks to marine machinery foundations. 1.2 The values stated in SI units shall be regarded as standard. The values in parentheses are for information only. 1.3 This standard does not purport to address the safety concerns associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Installation Procedures for Fitting Chocks to Marine Machinery Foundations