共找到 884 条与 复合材料与固体燃料 相关的标准,共 59 页
This standard is part of the series of EN metallic material standards for aerospace applications. The general organization of this series is described in EN 4258.
Aerospace series Paints and varnishes Corrosion resistant chromate free two component cold curing primer Part 6: High corrosion resistance for military application
A-A-59317, dated 28 August 1998, has been reviewed and determined to be valid for use in acquisition
CARBON BLACK, POWDERED, DRY
This handbook provides guidance for the ASE(Aircraft Survivability Equipment) data submittals, which will be completed prior to issue of a Safety of Flight(SOF) Release for testing of new/modified ASE equipment installed on U.S. Army aircraft. A combination of analyses, component testing, and ground testing will be used to issue the first release to test the system, which should be stipulated in each contract. The ADS-66 handbook would assist the contractor in determining the exact data/reports needed to assure airworthiness of the system.
GUIDANCE FOR DATA FOR SAFETY OF FLIGHT AIRWORTHINESS RELEASE FOR HELICOPTER AIRCRAFT SURVIVABILITY EQUIPMENT (ASE)
This drawing describes the requirements for IR secure indicator assemblies with panel sealing and panel and rear sealing with filtered type lens designed for sunlight viewing, with tireflection coated lens and available with electrostatic screen.
INDICATOR ASSEMBLIES: IR SECURE LIGHTING; RED, YELLOW, GREEN; PANEL SEALING
A-A-59121, dated 22 September 1997, has been reviewed and determined to be valid for use in acquisition
OXALIC ACID, DIHYDRATE, TECHNICAL
MS35794A remains inactive for new design, however, the document is valid for use
BEARING, SLEEVE, STEEL-BACKED BIMETAL, SPLIT TYPE, ONE PIECE
MIL-W-2902D remains inactive for new design, however, the document is valid for use.
WIRE ROPE ASSEMBLIES, SINGLE LEG, OXYGEN BREATHING APPARATUS SAFETY LINE
A-A-59211, dated 18 May 1998, has been reviewed and determined to be valid for use in acquisition
PARTS CLEANING CAN, SAFETY, BENCH [Superseded: NAVY RR-P-125 B CANC NOTICE 1, NAVY RR-P-125 B VALID NOTICE 1, NAVY RR-P-125 B, NAVY RR-P-125 A]
MS21783 remains inactive for new design, however, the document is valid for use.
BEARING, WASHER, THRUST, SINTERED BRONZE, OIL IMPREGNATED
MIL-B-5687D, dated 21 February 1984, is hereby reinstated as inactive for new design.
BEARINGS, SLEEVE, WASHERS, THRUST, SINTERED, METAL POWDER, OIL-IMPREGNATED, GENERAL SPECIFICATION FOR
MIL-C-440C, dated 17 November 1998, has been reviewed and determined to be valid for use in acquisition
COMPOSITIONS A-3 AND A-4
This specification covers requirements, examinations and tests for an explosive designated as Explosive Composition A-5.
EXPLOSIVE COMPOSITION A-5 [Use In Lieu Of: ARMY MIL-E-0014970 C CANC NOTICE 1]
This drawing describes the requirements for a family of metal card-retainers intended to hold circuit card ssemblies or printed wiring assemblies in their installed positions.
HOLDER, ELECTRICAL CARD, WEDGE RETAINER, 5-PIECE, .225 INCH BY .225 INCH AND .225 INCH BY .260 INCH BODY SIZE
This draft standard is based on European discussions in which the UK took an active part. Your comments on this draft are welcome and will assist in the preparation of the consequent British Standard. If no comments are received to the contrary, then the UK will approve this draft and implement it as a British Standard. Comment is particularly welcome on national, legislative or similar deviations that may be necessary.
Aerospace Series Aluminium Alloy AL-P7075-T73511 - Extruded Bar and Section a or D Less Than or Equal to 150 mm with Peripheral Coarse Grain Control Edition P1
MIL-C-45010A, dated 17 November 1998, has been reviewed and determined to be valid for use in acquisition
COMPOSITION C-4
This standard is part of the series of EN metallic material standards for aerospace applications. The general organization of this series is described in EN 4258. This standard has been prepared in accordance with EN 4500-2.
Aerospace Series Aluminium Alloy AL-P2014A T6511 Extruded Bars and Section a or D Less Than or Equal to 200 mm with Peripheral Coarse Grain Control Edition P 2
This drawing describes the requirements for a family of metal 5 wedge electrical card holders (hereafter referred to as card retainers) intended to hold circuit card assemblies or printed wiring assemblies in their installed positions.
HOLDER, ELECTRICAL CARD, WEDGE RETAINER, 5-PIECE, .250 INCH BY .260 INCH BODY SIZE
The General Services Administration has authorized the use of this commercial item description as a replacement for Military Specifications MIL-V-16720E and MIL-V-16721D which are cancelled.
HASP, HIGH SECURITY, SHROUDED, FOR HIGH AND MEDIUM SECURITY PADLOCK [Superseded: DLA MIL-H-43905 C CANC NOTICE 2, DLA MIL-H-43905 C NOTICE 1, DLA MIL-H-43905 C, DLA MIL-H-43905 B, DLA MIL-H-43905 A, DLA MIL-H-43905]
This industrial standard for the aerospace sector has been drawn up under the responsibility of AECMA
Aerospace Series Technical Drawings Representation of Parts Made of Composite Materials Part 6: Preforms Edition P 1
This "Aerospace Series" Prestandard has been drawn up under the responsibility of AECMA (Association Européenne des Constructeurs de Matériel Aérospatial). It is published on green paper for the needs of AECMA-Members. It has been technically approved by the experts of the concerned Technical Committee following comment by the Member countries.
Aerospace Series Technical Drawings Representation of Parts Made of Composite Materials Part 1: General Rules Edition P 1
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号