13.040.40 固定源排放限值 标准查询与下载
共找到 1179 条与 固定源排放限值 相关的标准，共 79 页
Stationary source emissions — Sampling and determination of mercury in flue gas using chemical absorption method
- ICS
- 13.040.40
- CCS
- 发布
- 2023-05
- 实施
Stationary source emissions — Determination of mass concentration of particulate matter (dust) at low concentrations — Manual gravimetric method
- ICS
- 13.040.40
- CCS
- 发布
- 2023-05
- 实施
Air quality — Measurement of stationary source emissions — Requirements for measurement sections and sites and for the measurement objective, plan and report
- ICS
- 13.040.40
- CCS
- 发布
- 2023-05
- 实施
Emission Standards of Air Pollutants for Printing Industry
- ICS
- 13.040.40
- CCS
- Z60
- 发布
- 2023-04-24
- 实施
- 2024-01-01
Air Pollutant Emission Standards for Automobile Manufacturing Industry
- ICS
- 13.040.40
- CCS
- Z60
- 发布
- 2023-04-24
- 实施
- 2024-01-01
Technical Specifications for Laboratory Exhaust Gas Pollution Control
- ICS
- 13.040.40
- CCS
- Z 05
- 发布
- 2023-03-23
- 实施
- 2023-04-23
1 Scope This document specifies procedures for establishing quality assurance levels (QAL) for automated measuring systems ( AMS ) installed on industrial plants for the determination of the flue gas components and other flue gas parameters. This document specifies: — a procedure (QAL2) to calibrate the AMS and determine the variability of the measured values obtained by it, so as to demonstrate the suitability of the AMS for its application, following its installation; — a procedure (QAL3) to maintain and demonstrate the required quality of the measurement results during the normal operation of an AMS , by checking that the zero and span characteristics are consistent with those determined during QAL1; — a procedure for the annual surveillance tests (AST) of the AMS in order to evaluate (i) that it functions correctly and its performance remains valid and (ii) that its calibration function and variability remain as previously determined. This document is designed to be used after the AMS has been certified in accordance with the series of documents EN 15267.
Stationary source emissions. Quality assurance of automated measuring systems
- ICS
- 13.040.40
- CCS
- 发布
- 2023-02-28
- 实施
- 2023-02-28
Stationary source emissions — Quality assurance of automated measuring systems
- ICS
- 13.040.40
- CCS
- 发布
- 2023-02-10
- 实施
- 2023-02
Emission Standards of Air Pollutants for Brick and Tile Industry
- ICS
- 13.040.40
- CCS
- Z 60
- 发布
- 2023-02-03
- 实施
- 2023-05-01
本标准规定了玻璃工业废气治理工程的污染物与污染负荷、总体要求、工艺设计、主要工艺设备和材料、检测及过程控制、主要辅助工程、劳动安全与职业卫生、施工与验收、运行与维护等技术要求。 本标准适用于平板玻璃制造的废气治理工程，可作为工程咨询、环境保护设施设计与施工、建设项目竣工环境保护验收及建成后运行管理的参考依据。 玻璃制品制造、玻璃纤维及制品制造、其他玻璃制造的废气治理工程可参考本标准执行。
Technical specifications for waste-gas treatment fromglass industry
- ICS
- 13.040.40
- CCS
- Z25
- 发布
- 2023-02-01
- 实施
- 2023-05-01
BS ISO 7935. Stationary source emissions. Determination of the mass concentration of sulfur dioxide in flue gases. Performance characteristics of automated measuring systems
- ICS
- 13.040.40
- CCS
- 发布
- 2023-01-25
- 实施
- 2023-01-25
Air Pollutant Emission Standards for Thermal Power Plants
- ICS
- 13.040.40
- CCS
- Z 60
- 发布
- 2023-01-05
- 实施
- 2023-03-01
Air Pollutant Emission Standards for Furniture Manufacturing Industry
- ICS
- 13.040.40
- CCS
- Z 60
- 发布
- 2023-01-05
- 实施
- 2023-03-01
Stationary source emissions — Determination of mass concentration of particulate matter (dust) at low concentrations — Manual gravimetric method
- ICS
- 13.040.40
- CCS
- 发布
- 2022-12-30
- 实施
Stationary source emissions — Determination of PM10/PM2.5 mass concentration in flue gas — Measurement at low concentrations by use of impactors
- ICS
- 13.040.40
- CCS
- 发布
- 2022-12-30
- 实施
Stationary source emissions — Determination of mass concentration of particulate matter (dust) at low concentrations — Manual gravimetric method
- ICS
- 13.040.40
- CCS
- 发布
- 2022-12-30
- 实施
Emission Standards of Air Pollutants for Chemical Fiber Industry
- ICS
- 13.040.40
- CCS
- Z60
- 发布
- 2022-12-30
- 实施
- 2023-01-30
Stationary source emissions — Automatic method for the determination of the methane concentration using flame ionization detection(FID)
- ICS
- 13.040.40
- CCS
- 发布
- 2022-12-30
- 实施
Stationary source emissions — Determination of the mass concentration of dinitrogen monoxide(N2O) — Reference method: Non-dispersive infrared method
- ICS
- 13.040.40
- CCS
- 发布
- 2022-12-30
- 实施
Stationary source emissions — Automatic method for the determination of the methane concentration using flame ionization detection(FID)
- ICS
- 13.040.40
- CCS
- 发布
- 2022-12-30
- 实施
