97.220.40 标准查询与下载

BS EN 1651:2018+A1:2020 滑翔伞设备 安全带 安全要求和强度测试

What is BS EN 1651 about?    BS EN 1651 discusses paragliding equipment. BS EN 1651 specifies safety requirements and test methods for paragliding harnesses. BS EN 1651 applies only to harnesses for paragliders. The intermediate attachment of the system between the harness and the paraglider does not form part of this standard.   Who is BS EN 1651 for?   BS EN 1651 on paragliding equipment (harnesses) is useful for:  

Paragliding equipment. Harnesses. Safety requirements and strength tests

BS EN 17232:2020 水上游乐设备及特点 安全要求、试验方法和操作要求

What is BS EN 17232 about?    BS EN 17232 discusses water play equipment and features. BS EN 17232 specifies safety requirements, test methods and operational requirements for installed water play equipment, features and structures intended for playing, and in areas intended for water activities for public use (non-domestic), typically in swimming pool facilities, and where water is an integral part in the use of the play equipment/feature/structures.   Play provision should aim at managing the balance between the need to offer risk and the need to keep children safe from serious harm. BS EN 17232 also applies to spray parks.   Note: BS EN 17232   does not apply to floating leisure articles according to EN ISO 25649 series, artificial climbing walls according to EN 12572 series, toys according to EN 71 series, water slides according to EN 1069 series, climbing/bouldering walls used in the swimming pool surround according to EN 17164 , water equipment/features (e.g., ornamental fountains) not intended for playing, water play equipment/features installed in swimming pools for domestic use, playground equipment according to EN 1176 series.  Who is BS EN 17232 for?

Water play equipment and features. Safety requirements, test methods and operational requirements

ASTM F2842-20 用于纯种和四分之一赛马的脊髓标准规范

1.1 The specification describes minimum performance criteria and describes test methods for reins for use in thoroughbred and quarter horse racing activities. 1.2 Except where noted, the values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Reins Used in Thoroughbred and Quarter Horse Racing

ASTM F1956-20 救护车标准规范

1.1 This specification covers six mechanical tests, one corrosion resistance test, and the minimum performance requirements for these tests. This specification applies to carabiners designed specifically for use by rescue personnel during both training exercises and actual rescue operations. This specification does not apply to recreational use carabiners. 1.2 Two different types of carabiners are defined in this specification, a heavy-duty rescue carabiner and a standardduty rescue carabiner. 1.3 Tests contained herein are destructive in nature. Carabiners subjected to any of these tests shall not be used in any way after testing except in evaluation the results of such testing. 1.4 This specification does not imply approval of any method of use of rescue carabiners. In addition, the tests described are laboratory tests and do not duplicate field conditions. Furthermore, the test load values contained herein are not to be interpreted as the forces which a rescue carabiner may be subjected to, or may be expected to sustain, in actual field use. 1.5 Quality control is solely the responsibility of the manufacturer or purchaser, or both, and is not addressed by this specification. 1.6 The values stated in SI units are to be regarded as the standard. 1.7 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Rescue Carabiners

ASTM F2030-11(2020) 彩弹射击缸爆炸盘组件的标准规范

Standard Specification for Paintball Cylinder Burst Disk Assemblies

ASTM F3249-20 Trestands 攀岩棒和三脚架或塔架的标准规格

1.1 This specification covers requirements for treestands, climbing sticks, and tripod/tower stands that are used for hunting, photographing, or general observation. Furthermore, this specification establishes minimum warning and package labeling, instructional content, safety device requirements, and physical testing parameters. This is a performance based specification and is not intended to restrict design. 1.2 Partial utilization of this specification is prohibited. Any statement of compliance with this specification shall be a certification that the product tested meets all of the requirements of the specification in its entirety. A product that fails to meet any one of the requirements of this specification is considered to have failed this specification and shall not be sold with any indication that it meets parts of the specification. 1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Treestands, Climbing Sticks, and Tripod or Tower Stands

BS EN ISO 21853:2020 风筝冲浪 发布系统 安全要求及测试方法

What is ISO 21853 about?    ISO 21853 discusses kiteboarding. While kiteboarding is an enjoyable water sport, it has inherent risks. One way to regain control in such situations is to activate the release system. ISO 21853 specifies the minimum safety requirements and test methods for a release system that reduces the pulling force of the kite and disconnects the user from the kite.   ISO 21853 is applicable for release systems that are operated intentionally by the user or another person and are used for the sport of kite boarding.   Who is ISO 21853 for?   ISO 21853 on kite boarding is useful for:   Kiteboarding equipment manufacturers   

Kite boarding. Release system. Safety requirements and test methods

EN ISO 21853:2020 风筝板.释放系统.安全要求和试验方法

This document specifies the minimum safety requirement and test methods for a release system that reduces the pulling force of the kite and disconnects the user from the kite. This document is applicable for release systems which are operated intentionally by the user or another person, and are used for the sport of kite boarding.

Kite boarding - Release system - Safety requirements and test methods (ISO 21853:2020)

ASTM F887-20 个人攀岩设备的标准规范

Table of Contents Section Title Section/ Paragraph Scope 1 Referenced Documents 2 Terminology 3 Significance and Use 4 Pole and Tree Climbers Classification 5 Ordering Information 6 Pole and Tree Climbers 7 Climber Gaffs 8 Climber Straps 9 Climber Pads 10 Climber Footplates 11 Body Belts, Positioning Devices and Wood Pole Fall Restriction Devices (WPFRD) Classification 12 Ordering Information 13 Two Dee Body Belts, Auxiliary Positioning Belts, and Four Dee Body Belts 14 Two Dee Body Belts 14.1 Auxiliary Positioning Belts and Four Dee Body Belts 14.2 Positioning Devices 15 Wood Pole Fall Restriction Device (WPFRD) 16 Arborist Saddle 17 Harnesses Classification 18 Ordering Information 18.2 Sizing 18.3 Marking 18.4 Energy Absorbing Lanyards Classification 19 Ordering Information 20 Energy Absorbing Lanyards 21 Qualification Testing After Exposure to an Electric Arc 22 Hardware Requirements 23 Test Equipment 24 Qualification Testing 25 Body Belts, Four Dee Body Belts, and Auxiliary Positioning Belts 25.1 Positioning Devices 25.2 WPFRD 25.3 Arborist Saddle 25.4 Harness 25.5 Energy Absorbers 25.6 Instructions 26 Table of Contents Section Title Section/ Paragraph Guarantee and Rejection 27 Keywords 28 1.1 This standard covers the specifications and qualification testing of the following: Climbers, Climber straps, Climber Pads, Climber Footplates, Body Belts, Work Positioning Devices with Locking Snaphooks/ Carabiners, Wood Pole Fall Restriction Devices (WPFRD), Arborist Saddle, Harnesses, Energy Absorbing Lanyards. These devices are used by workers in the climbing of poles, trees, towers, and other structures. Minimum performance criteria for harnesses and energy absorbing lanyards in arresting a fall after exposure to electric arcs are included for workers who may be exposed to thermal hazards of momentary electric arcs or flame. 1.2 Equipment may fall within one of the following categories: 1.2.1 Fall (Travel) Restraint—Prevents a user from reaching a fall hazard (allow 0 fall distance). 1.2.2 Work Positioning—Allows a 2 ft maximum free fall distance. 1.2.3 Fall Arrest—Allows a 6 ft maximum free fall distance with a maximum arrest force of 1800 lb. NOTE 1—Under certain conditions and with the use of equipment designed for such conditions, a 12-ft free-fall distance with a maximum arrest force of 1800 lb is allowed. 1.2.4 Suspension—Allows 0 free-fall distance while supporting the user’s weight. 1.2.5 Fall Restriction—to prevent or limit free fall from a work position or while ascending/descending a wood pole. 1.3 Three types of climbers, (Types A, B, and C) and two types of climber straps, Types (A and B) are covered. 1.4 Two types of body belts, (Types A and B) are covered. 1 This standard is under the jurisdiction of ASTM Committee F18 on Electrical Protective Equipment for Workers and are the direct responsibility of Subcommittee F18.15 on Worker Personal Equipment. Current edition approved Feb. 15, 2020. Published April 2020. Originally approved in 1984. Last previous edition approved in 2018 as F887 – 18. DOI: 10.1520/F0887-20. *A Summary of Changes section appears at the end of this standard Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. 1.5 Eight types of work positioning devices: three positioning straps, (Types A, B, and C), three adjustable-positioning lanyards, (Types A, B and C) and two nonadjustable positioning lanyards, (Types A and B) are covered. 1.6 Two types of WPFRD, (Types A and AB) are covered. 1.7 Arborist saddle, (Type A) Work Positioning and Suspension are covered. 1.8 Two types of harnesses, (Types A and B) are covered. 1.9 Two types of energy absorbing lanyards, (Types A and B) are covered. 1.10 The values stated in United States customary units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.11 The following safety hazards caveat pertains only to the test method portions, 9.2, 10.3, 11.2, 14.1.4, 15.3, 15.4, 16.2, 17.2, 18.4, 21.2, 22, 23, and 25 of this standard: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.12 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specifications for Personal Climbing Equipment

ISO 21853:2020 风筝板.释放系统.安全要求和试验方法

This document specifies the minimum safety requirement and test methods for a release system that reduces the pulling force of the kite and disconnects the user from the kite. This document is applicable for release systems which are operated intentionally by the user or another person, and are used for the sport of kite boarding.

Kite boarding — Release system — Safety requirements and test methods

T/CSGF 006-2020 智能固定式健身器材技术规范

本标准规定了智能固定式健身器材的术语和定义、电气要求、智能要求、信息安全、标识与说明、智能化能力的评价方法。本标准适用于全民健身中心、健身馆等场所安装的固定式健身器材。

Technical specification for smart stationary training equipment

ASTM F1774-20 攀岩和登山卡车的标准规范

1.1 This specification covers six mechanical tests and the minimum performance requirements for carabiners designed specifically for the sports of climbing and mountaineering. 1.2 Two different types of carabiners are defined in this standard, non-locking carabiners and locking carabiners. 1.3 Tests contained herein are destructive in nature. Carabiners subjected to any of these tests shall not be used in any way after testing except in evaluating the results of such testing. 1.4 This specification does not imply approval of any method of use of climbing and mountaineering carabiners. In addition, the test load values contained herein are not to be interpreted as the forces which a climbing and mountaineering carabiner may be subjected to, or expected to sustain in actual field use. 1.5 This specification is limited to carabiners made of steel or aluminum alloys only. 1.6 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Climbing and Mountaineering Carabiners

KS G 5807-2019 登山装备 - 动态登山绳 - 安全要求和试验方法

Mountaineering equipment — Dynamic mountaineering ropes — Safety requirements and test methods

KS G 5812-2019 登山设备连接器安全要求和试验方法

Mountaineering equipment－Connectors－Safety requirements and test methods

KS G 5813-2019 登山设备摩擦锚安全要求和试验方法

Mountaineering equipment－Frictional anchors－Safety requirements and test methods

KS G 5759-2019 游乐场设备－单杠

Playground equipment－Horizontal bars

KS G 5808-2019 登山设备冰爪安全要求和试验方法

Mountaineering equipment－Crampons－Safety requirements and test methods

KS G 5760-2019 游乐场设备双杠

Playground equipment－Parallel bars

KS G 5817-2019 登山设备 - 冰工具 - 安全要求和测试方法

Mountaineering equipment — Ice-tools — Safety requirements and test methods

KS G 5811-2019 登山设备垫块安全要求和试验方法

Mountaineering equipment－Chocks－Safety requirements and test methods